Page 1 INSTRUCTIONS Labels and Symbols Important Information — Please Read Before System Tablet Controller Chapter 1 Checking the Package Contents SC-1 Chapter 2 Nomenclature and Functions Chapter 3 Installation and Connection Chapter 4 Inspection Chapter 5 Operation Chapter 6 Reprocessing, Storage, and...
Page 3: Table Of Contents
Setting the system locale ..................40 Setting the language and time zone ..............45 Setting the time zone ......................45 Setting the language for an administrator account .............. 46 Language settings for a standard user account ..............52 SC-1 INSTRUCTION MANUAL...
Page 4 Chapter 7 Battery pack Replacement ..........75 Precautions for replacing the battery pack ............75 Replacing the battery pack ..................76 Chapter 8 Troubleshooting ..............79 Troubleshooting ..................... 79 Troubleshooting guide ................... 79 Returning the tablet for repair ................81 SC-1 INSTRUCTION MANUAL...
Page 5 IC Note (for Canada) ......................97 KC Note (for Korea) ......................98 NCC Warning (for Taiwan) ....................98 FCC RF Radiation Exposure Statement ................98 RF Exposure Information (SAR) ..................99 Windows license ......................100 MICROSOFT SOFTWARE LICENSE TERMS ..............100 SC-1 INSTRUCTION MANUAL...
Page 6 Contents SC-1 INSTRUCTION MANUAL...
Page 7: Labels And Symbols
Labels and Symbols Labels and Symbols Safety-related labels and symbols are attached on the locations shown below. If labels or symbols are missing or illegible, contact Olympus.  Rear Panel of the Tablet (SC-1) Label KC marking Crossed-out wheeled BSMI marking cULus marking bin’...
Page 8 Labels and Symbols  AC Adapter (Packaged with SC-1) Label Manufacturer Product name Polarity Model AC Input DC Output cRUus marking CAUTION (Indoor, medical electrical equipment, information technology equipmet) CE marking EN 60601-1, IEC 60601-1 compliance Efficiency level BIS marking Crossed-out wheeled bin’...
Page 9 Cradle (MAJ-2491) Label Crossed-out wheeled bin’ symbol BSMI marking cULus marking Refer to instruction manual marking Trademark Product name Model Rated voltage, Power input FCC marking CCC marking KC marking Serial number label CE marking Country of origin SC-1 INSTRUCTION MANUAL...
Page 10 Trademark RBRC marking KC marking Model Date manufactured Product name Rating voltage, Capacity Caution Capacity, Clamping voltage Country of origin Manufacturer marking BSMI marking Crossed-out wheeled Taiwan recycle marking bin’ symbol China RoHS marking CQC marking SC-1 INSTRUCTION MANUAL...
Page 11 Labels and Symbols  Back cover of this instruction manual Symbol Description Manufacturer Authorized representative in the European Community Date of manufacture For US Customers only For a Symbols Glossary, visit us: http://www.olympus-global.com/en/common/pdf/symbolsglossary.pdf SC-1 INSTRUCTION MANUAL...
Page 12: Important Information - Please Read Before Use
Keep this instruction manuals in a safe, accessible location. If you have any questions or comments about any information in this manual, contact Olympus.  Terms used in this manual Cradle Holds and charges the tablet.
Page 13: Instrument Compatibility
Chapter 8, “Troubleshooting”. If the problem cannot be solved by the information in Chapter 8, contact Olympus. This instrument is to be repaired by Olympus engineers only. Olympus is not liable for any injury or damage which occurs as a result of repairs attempted by non-Olympus personnel.
Page 14: Precautions
Otherwise it may result in electric shock or fire.  If the power cord or plug is damaged  If any liquid has penetrated in the tablet and/or accessories  If the tablet is exposed to high humidity SC-1 INSTRUCTION MANUAL...
Page 15 • If a battery pack is leaking, make sure that the liquid does not come in contact with your skin or eyes. If the liquid gets in your eye, do not rub it; immediately rinse with clean water, then see an eye doctor. Otherwise it may result in injury. SC-1 INSTRUCTION MANUAL...
Page 16 Otherwise the tablet and cradle may fall or drop and it could cause injury and/or damage to the tablet and accessories. • When placing the cradle on the adjustable arm, consider the range of movement of the cradle. Cradle may hit equipment around and it could cause damage to equipment. SC-1 INSTRUCTION MANUAL...
Page 17 • If updating software with security patch for OS, check the info provided by Olympus on the security patch that has been operationally verified as well as on the version info.
Page 18 Important Information — Please Read Before Use SC-1 INSTRUCTION MANUAL...
Page 19: Chapter 1 Checking The Package Contents
Match all items in the package with the components shown below. Inspect each item for damage. If the tablet and/or accessories are damaged, any component is missing, or you have any questions, do not use the tablet; immediately contact Olympus. ...
Page 20 1.1 Checking the package contents  Cradle (MAJ-2491) Ch.1 Cradle Screw ×4 Access information sheet  Battery Pack (MAJ-2493) Check when purchased a new battery pack for replacement. Battery Pack Replacement screw ×2 Access information sheet SC-1 INSTRUCTION MANUAL...
Page 21: Chapter 2 Nomenclature And Functions
2.1 Symbols and descriptions Chapter 2 Nomenclature and Functions Symbols and descriptions  Ch.2 Tablet Symbol Description Power ON/OFF For US Customers only For a Symbols Glossary, visit us: http://www.olympus-global.com/en/common/pdf/symbolsglossary.pdf SC-1 INSTRUCTION MANUAL...
Page 22: Tablet
Used for operating the tablet. CHARGE LED Indicates charging status. On (Orange): Charging Off: Not charging Blinking (Orange): Abnormal charging POWER LED Indicates system status. Green: Power ON Warm White: Standby Off: Power OFF Microphone Used when inputting sound. SC-1 INSTRUCTION MANUAL...
Page 23  Rear panel Ch.2 Nomenclature Description Speaker Used when outputting sound. Camera Used when taking pictures. Installing a camera application is required. Battery cover Removed when replacing the battery pack. Screw Removed when replacing the battery pack. SC-1 INSTRUCTION MANUAL...
Page 24 Rear panel (inside battery cover) Check when purchased a new battery pack for replacement. Ch.2 Nomenclature Description Battery housing Battery pack to be placed. Connecting terminal To be connected with the connecting terminal on the battery pack. SC-1 INSTRUCTION MANUAL...
Page 25 Protective cover for HDMI terminal to be removed when connecting a HDMI cable. After use, protective cover should be closed completely to assure waterproof performance. Docking connector For connecting to the cradle. Security slot For attaching a security cable (Kensington Lock). SC-1 INSTRUCTION MANUAL...
Page 26: Cradle
2.3 Cradle Cradle  Front Ch.2 Nomenclature Description Holder Used when docking/undocking the tablet. Handle Used to move the cradle to an easy-to-use position. SC-1 INSTRUCTION MANUAL...
Page 27 USB1 terminal For connecting a USB 2.0 compatible device. USB2 terminal For connecting a USB 3.0 compatible device. USB3 terminal USB4 terminal DC IN terminal For connecting the provided AC adapter to supply power to the tablet. SC-1 INSTRUCTION MANUAL...
Page 28: Battery Pack
Nomenclature Description Strap For removing the battery pack from the tablet. Connecting terminal To be connectied with the connecting terminal on the tablet (inside battery housing). Screw holes Used when fixing the battery pack to the tablet. SC-1 INSTRUCTION MANUAL...
Page 29: Chapter 3 Installation And Connection
If equipotentialization is not performed, equipment failure may result. NOTE • Do not throw away the package box to use it for storing the products. • Follow the conditions at each facility when connecting to the network. SC-1 INSTRUCTION MANUAL...
Page 30: Installation Workflow
Section 3.5 on page 28 Create a Windows account.  Section 3.6 on page 30 Set the system locate.  Section 3.7 on page 40 Set the language and time zone.  Section 3.8 on page 45 SC-1 INSTRUCTION MANUAL...
Page 31: Mounting The Cradle
• Refer to instruction manual for system control arm (MAJ-2151). • 4 screw holes on the back of the cradle to be used. • Cradle to be fixed to the system control arm with 4 screws packaged with the cradle. Figure 3.1 SC-1 INSTRUCTION MANUAL...
Page 32: Connection To The Power Supply
Power cord should be plugged in an easy-to-reach outlet, or power supply should be able to be disconnected from the whole system in which the tablet is set. Otherwise it may cause electric shock, fire, and/or damage of equipments. SC-1 INSTRUCTION MANUAL...
Page 33: Connection To The Power Supply
AC adapter should be placed in a horizontal and stable place. Otherwise cable may be pulled by the weight of AC adapter itself and it may cause disconnection. Connect the Olympus specified power cord to the AC adapter. Connect the power cord plug to a power outlet with a grounding electrode.
Page 34: Docking The Tablet
 Docking the tablet Lift the holder on top of the cradle. Figure 3.3 SC-1 INSTRUCTION MANUAL...
Page 35 • When power supply to the tablet is started, charging is to be started and the tablet is to be powered on. • When using the tablet undocked from the cradle, check battery level and charge if necessary. It may take 4 hours or so for full charge. SC-1 INSTRUCTION MANUAL...
Page 36: Creating An Account
Creating an account  Creating an administrator account Before creating an administrator account, log in with the default account. Default account: M008 Password: Olympus2020 Tap the start icon. Ch.3 Start Figure 3.6 Tap the settings icon. Settings Figure 3.7 SC-1 INSTRUCTION MANUAL...
Page 37 3.6 Creating an account Tap “Accounts”. Ch.3 Accounts Figure 3.8 Tap “Family & other users”. Family & other users Figure 3.9 SC-1 INSTRUCTION MANUAL...
Page 38 3.6 Creating an account Tap “Add someone else to this PC”. Ch.3 Add someone else to this PC Figure 3.10 SC-1 INSTRUCTION MANUAL...
Page 39 • At least 8 characters long • Contain at least three types of letters: uppercase letters, lowercase letters, symbols, and numbers • Must be different from the user name • Avoid using the same character more than 3 times Ch.3 Figure 3.11 SC-1 INSTRUCTION MANUAL...
Page 40 3.6 Creating an account Tap “Next”. Ch.3 Next Figure 3.12 SC-1 INSTRUCTION MANUAL...
Page 41 3.6 Creating an account Tap the account you have created. Ch.3 The account you have created Figure 3.13 Tap “Change account type”. Change account type Figure 3.14 SC-1 INSTRUCTION MANUAL...
Page 42 3.6 Creating an account Select “Administrator” from the list of account types. Ch.3 Administrator Figure 3.15 Tap “OK”. Figure 3.16 SC-1 INSTRUCTION MANUAL...
Page 43: Creating A Standard User Account
Take procedure following step 2 through 8 of “ Creating an administrator account” on page 30.  Deleting the default user account Ch.3 CAUTION Delete the default account for security. Tap the start icon. Tap the account icon. Account Figure 3.17 SC-1 INSTRUCTION MANUAL...
Page 44 Sign out Figure 3.18 Ch.3 Log in with an administrator account. Take procedure following step 2 through 5 of “ Creating an administrator account” on page 30. Tap the default account “M008”. Tap “Remove”. Remove Figure 3.19 SC-1 INSTRUCTION MANUAL...
Page 45 3.6 Creating an account Tap “Delete account and data”. Ch.3 Delete account and data Figure 3.20 SC-1 INSTRUCTION MANUAL...
Page 46: Setting The System Locale
3.7 Setting the system locale Setting the system locale NOTE Log in with an administrator account. Tap the start icon. Tap the settings icon. Tap “Time & Language”. Ch.3 Time & Language Figure 3.21 SC-1 INSTRUCTION MANUAL...
Page 47 3.7 Setting the system locale Tap “Region”. Ch.3 Region Figure 3.22 Tap “Additional date, time, & regional settings”. Additional date, time, & regional settings Figure 3.23 SC-1 INSTRUCTION MANUAL...
Page 48 3.7 Setting the system locale Tap “Region”. Ch.3 Region Figure 3.24 Tap “Administrative”. Administrative Figure 3.25 SC-1 INSTRUCTION MANUAL...
Page 49 3.7 Setting the system locale Tap “Change system locale”. Ch.3 Change system locale Figure 3.26 Set “Current system locale” to an appropriate one, then tap “OK”. Figure 3.27 SC-1 INSTRUCTION MANUAL...
Page 50 3.7 Setting the system locale Tap “Restart now”. Restart now Ch.3 Figure 3.28 SC-1 INSTRUCTION MANUAL...
Page 51: Setting The Language And Time Zone
Setting the language and time zone NOTE Set it for each account you create.  Setting the time zone Ch.3 Log in with any account. Tap the start icon. Tap the settings icon. Tap “Time & Language”. Time & Language Figure 3.29 SC-1 INSTRUCTION MANUAL...
Page 52: Setting The Language For An Administrator Account
3.8 Setting the language and time zone Set the time zone to the appropriate region. Ch.3 Figure 3.30  Setting the language for an administrator account Tap the start icon. Tap the settings icon. SC-1 INSTRUCTION MANUAL...
Page 53 3.8 Setting the language and time zone Tap “Time & Language”. Ch.3 Time & Language Figure 3.31 Tap “Region”. Region Figure 3.32 SC-1 INSTRUCTION MANUAL...
Page 54 3.8 Setting the language and time zone Set the country or region appropriately. Ch.3 Figure 3.33 Tap “Language”. Language Figure 3.34 SC-1 INSTRUCTION MANUAL...
Page 55 3.8 Setting the language and time zone Select the desired language. Ch.3 Figure 3.35 Tap “Administrative language settings”. Administrative language settings Figure 3.36 SC-1 INSTRUCTION MANUAL...
Page 56 3.8 Setting the language and time zone Tap “Copy settings”. Copy settings Ch.3 Figure 3.37 Tap “Welcome screen and system accounts” to check it. Welcome screen and system accounts Figure 3.38 SC-1 INSTRUCTION MANUAL...
Page 57 3.8 Setting the language and time zone Tap “OK”. Ch.3 Figure 3.39 Tap “Restart now”. Restart now Figure 3.40 SC-1 INSTRUCTION MANUAL...
Page 58: Language Settings For A Standard User Account
Take procedure following Step 1 through 7 of “ Creating an administrator account” on page 30. Close the settings window. Tap the start icon. Tap the power icon. Ch.3 Power Figure 3.41 Tap “Restart”. Restart Figure 3.42 SC-1 INSTRUCTION MANUAL...
Page 59: Chapter 4 Inspection
• Before each use, inspect as instructed below. Should any irregularity be observed, do not use and refer to Chapter 8, “Troubleshooting”. If the irregularity is still Ch.4 observed after consulting Chapter 8, contact Olympus. Otherwise improper performance, an electric shock, burn, and/or a fire may result. SC-1 INSTRUCTION MANUAL...
Page 60: Inspection Workflow
Section 4.5 on page 55 Ch.4 Check the battery level and power supply.  Section 4.6 on page 56 Set the tablet to sleep mode. (if not used for a while after checking)  Section 4.7 on page 57 SC-1 INSTRUCTION MANUAL...
Page 61: Checking If The Cradle Is Properly Mounted On The System Control Arm
(POWER LED turns Green). POWER Figure 4.1 NOTE When peripheral devices are connected with the cradle, communication between the tablet and peripheral devices will be disconnected if the tablet is removed from the cradle, SC-1 INSTRUCTION MANUAL...
Page 62: Checking The Battery Level And Power Supply
Log in with the desired user account. Check the battery icon to see remaining battery level. Battery icon Ch.4 Figure 4.2 Check the battery icon to see if the tablet is connected to the power supply. Battery icon Figure 4.3 SC-1 INSTRUCTION MANUAL...
Page 63: Sleep Mode
If you press and hold the power button too long, tablet will be powered off. Make sure that the display turns off and the POWER LED turns Warm White a few seconds later. Press the power button to wake up the tablet. Power button Ch.4 POWER Figure 4.4 SC-1 INSTRUCTION MANUAL...
Page 64 4.7 Sleep mode Ch.4 SC-1 INSTRUCTION MANUAL...
Page 65: Chapter 5 Operation
Otherwise improper performance, equipment damage, an electric shock, burn, and/or a fire may result. • Do not use a humidifier near the tablet and accessories as condensation may occur and cause a fire and/or tablet and accessories failure. Ch.5 SC-1 INSTRUCTION MANUAL...
Page 66: Operation Workflow
(If not using the tablet temporarily)  Section 4.7 on page 57 Ch.5 Charging.  Section 5.4 on page 62 Power off. (If shutting down)  Section 5.5 on page 63 Care and store after use.  Chapter 6 on page 65 SC-1 INSTRUCTION MANUAL...
Page 67: Adjusting The Tablet Position
Adjusting the tablet position Hold the handle to adjust the tablet to any position. NOTE The system control arm allows you to move the arm horizontally and tilt the tablet up, down, left, or right. Ch.5 Figure 5.1 SC-1 INSTRUCTION MANUAL...
Page 68: Charging
If around the battery cover of the tablet is too hot, undock the tablet from the cradle and wait until the tablet cools down, then try charging again. Ch.5 SC-1 INSTRUCTION MANUAL...
Page 69: Power Off
5.5 Power off Power off Tap the start icon. Start Figure 5.2 Tap the power icon. Ch.5 Power Figure 5.3 Tap “Shut down”. Shut down Figure 5.4 SC-1 INSTRUCTION MANUAL...
Page 70 5.5 Power off Ch.5 SC-1 INSTRUCTION MANUAL...
Page 71: Chapter 6 Reprocessing, Storage, And Disposal
1 hour after the patient procedure. Patient debris will begin to dry and solidify, hindering effective removal and reprocessing efficacy. • Insufficiently reprocessing for this instrument may pose an infection control risk to operators who touch it. SC-1 INSTRUCTION MANUAL...
Page 72: Detergent Solution And Disinfectant Solution
• When patient debris enters a hole or gap of this instrument, contact Olympus without disinfecting it. If you try to disinfect by force, the disinfectant solution will get inside this instrument, causing fire and malfunction of this instrument.
Page 73: Preparing Equipment For Reprocessing
*2 Lint-free cloths are recommended for reprocessing to prevent lint or cloth fibers from lodging or being trapped in the instrument’s components. If gauze is used to reprocess the container, ensure that fibers do not get caught on. SC-1 INSTRUCTION MANUAL...
Page 74: Reprocessing Procedure
1. Confirm the appearance of the tablet Ch.6 2. Patient debris directly or indirectly adheres to this instrument 3. Disinfection is necessary according to national, local, or facility standards Disinfection Cleaning (“ Disinfection”) (“ Cleaning”) Figure 6.1 SC-1 INSTRUCTION MANUAL...
Page 75 Ch.6 Lint-free cloth moistened with detergent solution detergent solution Figure 6.2 Wipe off all patient debris from this instrument using the moistened lint-free cloth. Make sure that you wipe LCD lightly so LCD will not be damaged. SC-1 INSTRUCTION MANUAL...
Page 76 Ensure that the surfaces are completely wet for the contact time instructed by the disinfectant solution manufacture. If any surface of this instrument remains wet, wipe it with a dry lint-free cloth and let it dry thoroughly. Ch.6 SC-1 INSTRUCTION MANUAL...
Page 77 Make sure that you wipe LCD lightly so LCD will not be damaged. If any surface of this instrument remains wet, wipe it with a dry lint-free cloth and let it dry thoroughly. Ch.6 SC-1 INSTRUCTION MANUAL...
Page 78: Storage
Put the tablet and accessories in the package box. Store the tablet and accessories in a clean, dry place where the tablet can be placed horizontally and where there is no risk of scratching the surface of the tablet. SC-1 INSTRUCTION MANUAL...
Page 79: Disposal
6.3 Disposal Disposal When disposing the tablet and accessories, follow all applicable national and local laws and guidelines. Ch.6 SC-1 INSTRUCTION MANUAL...
Page 80 6.3 Disposal Ch.6 SC-1 INSTRUCTION MANUAL...
Page 81: Chapter 7 Battery Pack Replacement
Chapter 7 Battery pack Replacement Precautions for replacing the battery pack Always use the battery pack designated below. To order a new battery pack, contact Olympus. • Battery Pack MAJ-2493 WARNING Do not use a battery pack not specified for your tablet. Using the wrong type of battery could result in an explosion, fire, or smoke.
Page 82: Replacing The Battery Pack
Loosen the 10 screws which secure the battery cover, then open the battery cover. Figure 7.1 CAUTION If any screw for the battery cover is missing, due to any damage, contact Olympus. NOTE Ch.7 Do not remove those 10 screws from the battery cover.
Page 83 Do not touch the terminals on the battery pack and on the tablet battery housing. If terminals are damaged, charging will not be possible. Connect and fix the terminals on the battery pack and on the tablet battery housing. Figure 7.5 SC-1 INSTRUCTION MANUAL...
Page 84 • Make sure that no foreign object is stuck under the battery cover. Otherwise gap will be found and watertightness will not be assured. Dock the tablet in the cradle following Section 3.5, “Docking the tablet” to check whether charging is possible or not. SC-1 INSTRUCTION MANUAL...
Page 85: Chapter 8 Troubleshooting
Section 3.5, “Docking the tablet”. Wire in the USB cable is disconnected. Replace the USB cable. USB device has broken down. Try the USB device with other equipment to see if the USB device would be recognized or not. SC-1 INSTRUCTION MANUAL...
Page 86 Section 5.5, “Power off”. Problem occurring in Windows system. Press and hold the tablet power button Ch.8 (5-6 seconds) to power off. When it is off, follow Section 4.5, “Power on” to make sure tablet starts properly. SC-1 INSTRUCTION MANUAL...
Page 87: Returning The Tablet For Repair
8.3 Returning the tablet for repair Returning the tablet for repair When returning the tablet for repair, contact Olympus. With the tablet, include a description of the malfunction or damage and the name and telephone number of the individual at your location who is most familiar with the problem.
Page 88 8.3 Returning the tablet for repair Ch.8 SC-1 INSTRUCTION MANUAL...
Page 89: Appendix
The recommended combinations of equipment that can be used with the tablet and accessories are listed below. New products released after the introduction of the tablet and accessories may also be compatible for use in combination with it. For further details, contact Olympus. System Control Arm...
Page 90: Specifications
(10.2 – 15.4 psia) Transportation Ambient temperature –20 to +60C (–4 to +140F) environment Relative humidity 10 – 95% (conditions during Atmospheric 700 – 1060 hPa transportation and pressure (0.7 – 1.1 kgf/cm short-term storage) (10.2 – 15.4 psia) App. SC-1 INSTRUCTION MANUAL...
Page 91: Specifications
EMC standard for medical electrical equipment edition, the EMC characteristics could be vulnerable. • CISPR 11 of emission: App. Group 1, Class B RoHS Directive This device complies with the requirements of Directive 2011/65/EU concerning electrical and electronic equipment. SC-1 INSTRUCTION MANUAL...
Page 92 Electrical and Electronic Equipment, this symbol indicates that the tablet must not be disposed of as unsorted municipal waste, but should be collected separately. Refer to your local Olympus distributor for return and/or collection systems available in your country. Display LCD Size 11.6”...
Page 93 This expected lifetime is effective only if the tablet is properly used following the conditions as below: • Inspection before each use as well as periodic inspection described in the “Instruction Manual” to be operated. • To be repaired if it is decided necessary after inspection. App. SC-1 INSTRUCTION MANUAL...
Page 94 Specifications App. SC-1 INSTRUCTION MANUAL...
Page 95 Electrical and Electronic Equipment, this symbol indicates that the tablet must not be disposed of as unsorted municipal waste, but should be collected separately. Refer to your local Olympus distributor for return and/or collection systems available in your country. SC-1 INSTRUCTION MANUAL...
Page 96 Electrical and Electronic Equipment, this symbol indicates that the tablet must not be disposed of as unsorted municipal waste, but should be collected separately. Refer to your local Olympus distributor for return and/or collection systems available in your country. SC-1 INSTRUCTION MANUAL...
Page 97: Fcc (For The Tablet, And The Cradle) (For The Usa)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. App. SC-1 INSTRUCTION MANUAL...
Page 98: Emc Information
IEC 61000-4-2 hardly produces static. If floors Air: Air: 2, 4, 8, 15 kV 2, 4, 8 kV are covered with synthetic material that tends to produce static, the relative humidity should be at least 30%. SC-1 INSTRUCTION MANUAL...
Page 99 Same as left It is recommended to use this (50/60 Hz) (50 Hz or 60 Hz) (50 Hz, 60 Hz) instrument by maintaining magnetic field enough distance from any IEC 61000-4-8 equipment that operates with high current. SC-1 INSTRUCTION MANUAL...
Page 100 • These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. App. • Electromagnetic interference may occur in the vicinity of high-frequency electrosurgical equipment and/or other equipment marked with the following symbol: SC-1 INSTRUCTION MANUAL...
Page 101 If abnormal performance is observed, additional measures may be necessary, such as re-orienting or relocating this model. Over the frequency range 150 kHz to 80 MHz, field strength should be less than 3 V/m. App. SC-1 INSTRUCTION MANUAL...
Page 102 Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of the tablet and the cradle, including cables specified by Olympus. Otherwise degradation of the performance of this equipment could result.
Page 103: Fcc Note (For The Usa)
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Cet appareil et son antenne (s) ne doivent pas être situés ou fonctionner en conjonction avec une autre antenne ou émetteur. SC-1 INSTRUCTION MANUAL...
Page 104 (i)the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (For devices installed in vehicles point i. is not required.) (ii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p.
Page 105: Kc Note (For Korea)
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment for body-worn configuration in direct contact to the phantom. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. SC-1 INSTRUCTION MANUAL...
Page 106 FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: X4D-SC-1 低功率電波輻射性電機管理辦法第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、...
Page 107: Windows License
You must comply with that policy, which might require you to return the software with the entire device on which the software is installed for a refund or credit, if any. SC-1 INSTRUCTION MANUAL...
Page 108 Updating or upgrading from non-genuine software with software from Microsoft or authorized sources does not make your original version or the updated/upgraded version genuine, and in that situation, you do not have a license to use the software. SC-1 INSTRUCTION MANUAL...
Page 109 This section does not mean, however, that you have the right to install the software, or use the primary function of the software (other than the features listed in this section), on any of these other devices. SC-1 INSTRUCTION MANUAL...
Page 110 Windows label including the product key. Before any permitted transfer, the other party must agree that this agreement applies to the transfer and use of the software. SC-1 INSTRUCTION MANUAL...
Page 111 Neither the device manufacturer or installer, nor Microsoft, is obligated to supply earlier versions to you. You must obtain the earlier version separately, for which you may be charged a fee. At any time, you may replace an earlier version with the version you originally acquired. SC-1 INSTRUCTION MANUAL...
Page 112 These are your only remedies for breach of warranty. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state or country to country. SC-1 INSTRUCTION MANUAL...
Page 113 (iii) Australia. If you acquired the software in Australia, contact Microsoft to make a claim at 13 20 58; or Microsoft Pty Ltd, 1 Epping Road, North Ryde NSW 2113 Australia. (iv) Other countries. If you acquired the software in another country, contact the Microsoft affiliate serving your country (aka.ms/msoffices). SC-1 INSTRUCTION MANUAL...
Page 114 (or, if a business, your principal place of business) or our principal place of business?King County, Washington USA if your dispute is with Microsoft. SC-1 INSTRUCTION MANUAL...
Page 115 Section 11 will be unenforceable in its entirety. h. Conflict with AAA rules. This agreement governs if it conflicts with the AAA’s Commercial Arbitration Rules or Consumer Arbitration Rules. SC-1 INSTRUCTION MANUAL...
Page 116 You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. To learn more about your rights under the Australian Consumer Law, please review the information at (aka.ms/acl). SC-1 INSTRUCTION MANUAL...
Page 117 H.264/AVC and MPEG-4 visual standards and VC-1 video standards. The software may include H.264/MPEG-4 AVC and/or VC-1 decoding technology. MPEG LA, L.L.C. requires this notice: SC-1 INSTRUCTION MANUAL...
Page 118 If you provide Microsoft comments, suggestions or other feedback about the preview (“submission”), you grant Microsoft and its partners rights to use the submission in any way and for any purpose. SC-1 INSTRUCTION MANUAL...
Page 119 There are also informational links in this agreement. The links containing notices and binding terms are: • Microsoft Privacy Statement (aka.ms/privacy) • Microsoft Services Agreement (aka.ms/msa) • Adobe Flash Player License Terms (aka.ms/adobeflash) App. SC-1 INSTRUCTION MANUAL...
Page 120 ©2019 OLYMPUS MEDICAL SYSTEMS CORP. All rights reserved. No part of this publication may be reproduced or distributed without the express written permission of OLYMPUS MEDICAL SYSTEMS CORP. OLYMPUS is a registered trademark of OLYMPUS CORPORATION. Trademarks, product names, logos, or trade names used in this document are generally registered trademarks or trademarks of each company.
Page 121 Manufactured by 2951 Ishikawa-cho, Hachioji-shi, Tokyo 192-8507, Japan Fax: (042)646-2429 Telephone: (042)642-2111 Distributed by 3500 Corporate Parkway, P.O. Box 610, Center Valley, PA 18034-0610, U.S.A. Fax: (484)896-7128 Telephone: (484)896-5000 5301 Blue Lagoon Drive, Suite 290 Miami, FL 33126-2097, U.S.A. Fax: (305)261-4421 Telephone: (305)266-2332 (Premises/Goods delivery) Wendenstrasse 14-18, 20097 Hamburg, Germany (Letters) Postfach 10 49 08, 20034 Hamburg, Germany Fax: (040)23773-4656 Telephone: (040)23773-0...

Olympus SC-1 Instruction Manual

Chapter 1 Checking the Package Contents

Chapter 2 Nomenclature and Functions

Chapter 3 Installation and Connection

Chapter 4 Inspection

Chapter 5 Operation

Chapter 6 Reprocessing, Storage, and Disposal

Chapter 7 Battery Pack Replacement

Chapter 8 Troubleshooting

Appendix

Quick Links

Related Manuals for Olympus SC-1

Summary of Contents for Olympus SC-1

Table of Contents