Table of Contents
Advertisement
Quick Links
Original Instructions, Revision 1 August 2020
ROTOR METER 65 & 130
i-CON
Original Operating Manual and parts list
Read carefully before installation and
operation
This document must not be copied duplicated or distributed without prior consent .
All and patent rights apply
STOCKS AG LIMITED, CROMWELL ROAD, WISBECH, CAMBRIDGESHIRE, UK.
Tel: 00 44 (0) 1945 464 909 Email: sales@stocks-ag.co.uk www.stocks-ag.co.uk
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Stocks AG i-CON 65
Summary of Contents for Stocks AG i-CON 65
- Page 1 Read carefully before installation and operation This document must not be copied duplicated or distributed without prior consent . All and patent rights apply STOCKS AG LIMITED, CROMWELL ROAD, WISBECH, CAMBRIDGESHIRE, UK. Tel: 00 44 (0) 1945 464 909 Email: sales@stocks-ag.co.uk www.stocks-ag.co.uk...
- Page 2 Index Section Page No. Index General information Technical data Intended use Unintended use Contents of the EC Declaration of Conformity Contents of the UKCA Declaration of Conformity Machine identification Warranty Safety Emergency Stop Instructions Maintenance Safety warning decals and safety signs 11-1 Clearing a blockage 11-2...
-
Page 3: General Information
3-1 General information Congratulations on your Rotor Metre purchase; Please check the machine for any transport damage upon receipt and advise your supplier of any problems immediately. Late claims regarding any damage may be rejected. IMPORTANT This Operating Manual forms part of the machine and must be readily available for the operator who must read and follow the points covered before use 3-2 Technical data Model: Rotor Meter (Gravity Fed) - Page 4 Safety of machinery – Safety distances to prevent hazard zones aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaabeing reached by the upper and lower limbs. The manufacturer stated above holds the technical file for this machine. Signed on behalf of Stocks Ag Ltd Name: J Woolway Date:...
- Page 5 Safety of machinery – Safety distances to prevent hazard zones aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaabeing reached by the upper and lower limbs. The manufacturer stated above holds the technical file for this machine. Signed on behalf of Stocks Ag Ltd Name: J Woolway Date:...
-
Page 6: Machine Identification
ROTOR METER MK 2 MODEL 217200 SERIAL No MANUFACTURED 2021 BY:- STOCKS AG LIMITED CROMWELL ROAD WISBECH, CAMBS. PE14 OSD, UK The machine the serial number decals are mounted on the steel chassis to one side of the hopper 6-2 Warranty We provide a 12 month warranty as of the date of invoice (your invoice for the machine which will serve as a warranty certificate). - Page 7 After working the machine ensure that any unused product is returned safely to its original packaging Stocks AG Ltd. does not accept any liability for the storage and use of the material being applied If unsure contact the material supplier for more information.
- Page 8 8 Emergency stop instructions 1. Power down the control system immediately by pressing and holding down the left-hand rubber end cap on the instrument control panel for approx. 2 seconds — then release to power off. 2. Disconnect the power supply by unplugging the power cable or removing the inline 40amp fuse.
-
Page 9: Maintenance
9 Maintenance WARNING Always ensure the power supply is disconnected before any maintenance work or cleaning of this machine. Suitable protective clothing must be worn (See page 7) The machine must be checked regularly by the operator for any damage loose bolts or electrical connec- tions, vibrations, unusual sounds, and to ensure they function correctly. -
Page 10: Safety Warning Decals
10 Safety Warning Decals Important ; observe this safely decals on the machine WARNING Read and understand the Operators Manual instructions before operating this machine Operator errors can result in serious injury WARNING Danger moving parts Risk of serious injury whilst the machine is in operation WARNING Risk of injury... -
Page 11: Clearing A Blockage
11-1 Clearing a blockage Disconnect the main power supply Ensure the parent machine is stationary, switched off, and parked on level ground Ensure the main power switch on the control panel is off and unplug the power supply cable or disconnecting the power cable from the vehicle battery. -
Page 12: Machine Mounting
12 Machine Mounting Mount the machine using the Base Plate. This has 4 holes in the base to take M12 bolts (see below) use these to attach to the parent vehicle and is attached to the chassis by 2 bolts and spacers which act as the pivot, and a removable steel pin secured by an ‘R’... -
Page 13: Wiring Diagram
13-1 i-CON Control system All control system components integral to the applicator unit are factory fitted. The Instrument has a 4.3" Colour Touch Screen which has 4 basic menu keys (see page 16) Separate power cable and head unit leads interconnect the tractor and the Seed Applicator Unit. The following components need to be installed during fitment (packed in hopper from factory) ... -
Page 14: Machine Components
The 6m instrument lead connects to the junction box mounted on the machine, and runs to the i-Con instrument panel connector lead in the tractor cab. NOTE Extension power and instrument cables are available if required. Please contact your local Stocks AG dealer for more information. - Page 15 15-1 i-CON Instrument functions Applica on Rate (kg/ha or Seeds/m ) and Forward Speed / Area and % Nudge from Target Opera ng Range (0-100%) Indicator Nudge – Increase Manual Pre-Start Nudge – Decrease Forward Speed or Area display Set Applica on Rate Metering On/Off...
-
Page 16: Changing The Feed Rollers
The assembled rollers and spacers should not be under compression. NOTE. You should be able to rotate the feed shaft with your fingers – if it feels excessively tight, check the feed roller and spacer composition or call Stocks AG for advice. WARNING... - Page 17 17 5mm feed roller combinations Feed rollers and spacer arrangement for 1 outlet machines 1 24mm Black Spacer Stainless Shim Washer A 5mm Feed Rollers (see page 14) Feed rollers and spacer arrangement for 3 outlet machines and 2 outlet opera on 3mm White Spacer Stainless Shim Washer 24mm Black Spacer...
- Page 18 18 8 section feed roller combinations Feed roller and spacer arrangement for 1 outlet machines fi ed with 1 feed roller 1 3mm White Spacer 2 28mm Spacer 5mm Black Spacer Feed Roller 6.5mm white Spacer Feed rollers and spacer arrangement for 1 outlet machines fi...
- Page 19 19 i-CON Calibration (Page 1 of 2) You will need a suitable container to collect the product or seed when calibrating, and an accurate set of scales which weighs in grams At the machine 1. Air Force Models only switch the fan OFF at the junction box 2.
- Page 20 20 i-CON Calibration (Page 2 of 2) 1. For a Manual Calibration Press and hold the Prime button on the junction box, the larger the quantity dispersed the higher the accuracy the final calibration factor will be, release the prime button once sufficient product has been dispensed 1.
-
Page 21: Parts Drawing
21 Rotor Meter i-CON 65L & 130L Parts drawing Please refer to pages 15 and 16 showing feed roller and spacers combinations 9, 10a & 10b 7, 8a & 8b Air-Force Control... - Page 22 22 Rotor Meter i-CON 65L & 130L Parts list (page 1) Item Part # Description Remarks FJ003A-Ass. Hopper Bracket 65L hopper FJ003A-Ass. Hopper Bracket 130L hopper FJ017D Hopper Base Plate FJ017S Base Plate Seal FJ026A-Ass. 65 Litre Hopper FJ026B-Ass. 130 Litre Hopper FJ027A-Ass.
- Page 23 23 Rotor Meter i-CON 65L & 130L Parts list (page 2) Item Part # Description Remarks M5–012 M5 x 25 Slot Head CSK Screw Qty x 6 on 130L M5-014 M5 Flat Washer Qty x 6 on 130L M5-017 M5 Nyloc Nut Qty x 6 on 130L M6-005 M6x20 Hex Head Screw...
Need help?
Do you have a question about the i-CON 65 and is the answer not in the manual?
Questions and answers