Advertisement
Quick Links
JEDI RGBW
220/240V 50/60Hz
+40°C
-25°C
In caso di dubbi sulla simbologia,
riferirsi al catalogo o al sito web.
If in doubt about the symbols refer
to catalog or website
RG1 secondo norma IEC/TR 62778:2014 / RG1 in accordance with IEC/TR 62778:2014
RG1 selon la norme IEC/TR 62778:2014 / RG1 nach der norm IEC/TR 62778:2014
RG1 enlight IEC/TR 62778:2014 / RG1 volgens IEC/TR 62778:2014
TARGETTI SANKEY S.p.A. Via Pratese n°164 Florence Italy
RG1 de acordo com norma IEC/TR 62778:2014
cod. 2CU7CS00_101
20W Sorgente Led / Led source
24W Apparecchio / Fixture
COD.1E3099 / 1E3100 / 1E3101 / 1E3102
COD 1E3111 / 1E3112 / 1E3113 / 1E3114
30W Sorgente Led / Led source
36W Apparecchio / Fixture
COD. 1E3103 / 1E3104 / 1E3105 / 1E3106
COD. 1E3115 / 1E3116 / 1E3117 / 1E3118
40W Sorgente Led / Led source
49W Apparecchio / Fixture
COD. 1E3107 / 1E3108 / 1E3109 / 1E3110
COD. 1E3119 / 1E3120 / 1E3121 / 1E3122
PRJ
600mm
2,4
900mm
3,4
1200mm
4,4
IK
Proiettore
08
Projector
Incassato
10
Recessed
INC
3,5
4
6,8
F
IP
/
66
66
20KN
67
www.targetti.com
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Targetti JEDI RGBW
Summary of Contents for Targetti JEDI RGBW
- Page 1 RG1 secondo norma IEC/TR 62778:2014 / RG1 in accordance with IEC/TR 62778:2014 RG1 selon la norme IEC/TR 62778:2014 / RG1 nach der norm IEC/TR 62778:2014 RG1 enlight IEC/TR 62778:2014 / RG1 volgens IEC/TR 62778:2014 RG1 de acordo com norma IEC/TR 62778:2014 www.targetti.com TARGETTI SANKEY S.p.A. Via Pratese n°164 Florence Italy...
- Page 2 L’appareil doit être installer par électriciens qualifies. Targetti ne peut pas être responsable pour toutes les installations qui ne respectent pas les normes de sécurité en vigueur. Das Gerät muss von Elektroinstallateuren montiert werden.
- Page 3 Суммарная мощность светильников при шлейфовом соединении не должна быть больше 1500 Вт. Пожалуйста, учитывайте данные о мощности каждого прожектора, указанные в техническом описании. 灯具串接最大限制功率 为 1500W, 请 核 对 用户手册每款灯具对应的功率 中国 www.targetti.com TARGETTI SANKEY S.p.A. Via Pratese n°164 Florence Italy...
- Page 4 H07RN8-F Ø7mm÷12mm MAX SERRARE PER GARANTIRE LA TENUTA Per cablare il connettore looping TIGHTEN TO occorre rimuovere il tappo. ENSURE To connect the looping plug TIGHTNESS the cap must be removed. www.targetti.com TARGETTI SANKEY S.p.A. Via Pratese n°164 Florence Italy...
- Page 5 SERRARE PER GARANTIRE LA TENUTA TIGHTEN TO ENSURE TIGHTNESS USARE CAVO DMX STANDARD CODICE TARGETTI "1T1932" O SIMILARE Ø7mm÷12mm MAX USE CABLE DMX STANDARD TARGETTI CODE "1T1932" OR SIMILAR Ø7mm÷12mm MAX www.targetti.com TARGETTI SANKEY S.p.A. Via Pratese n°164 Florence Italy...
- Page 6 PER CONNESSIONE DMX OUT RIMUOVERE TAPPO CHIUSURA FOR DMX OUT CONNECTION REMOVED END CAP TAPPO CHIUSURA END CAP www.targetti.com TARGETTI SANKEY S.p.A. Via Pratese n°164 Florence Italy...
- Page 7 SCHEMA DI COLLEGAMENTO PER DMX WIRING CONNECTION SCHEME FOR DMX JEDI RGBW WIRING (BUILT-IN DMX BUFFER NOT USED) GROUND USED DMX "-" USED DMX "+" www.targetti.com TARGETTI SANKEY S.p.A. Via Pratese n°164 Florence Italy...
- Page 8 JEDI RGBW WIRING (BUILT-IN DMX BUFFER USED) GROUND USED DMX "-" USED DMX "+" GROUND DMX "+" USED DMX "-" USED www.targetti.com TARGETTI SANKEY S.p.A. Via Pratese n°164 Florence Italy...
Need help?
Do you have a question about the JEDI RGBW and is the answer not in the manual?
Questions and answers