Table of Contents
Advertisement
MAINTENANCE
There are no predetermined maintenance intervals for this appliance
however the following should be observed.
1. Inspect hoses and replace if they are not in order, before us
ing the appliance as cracked and perished hoses can be
dangerous replace if necessary with hoses as detailed in point 5.
2. Allow the appliance to cool sufficiently before attempting any
maintenance.
3. The appliance is fitted with a jet to regulate the correct amount
of gas. The small hole in the jet may become blocked, result
ing in a small flame or no flame on the burner. To clean, unscrew
it from the appliance Clean the jet by blowing the hexagon end,
or by using a jet cleaner. Do NOT attempt to clean the jet with
a sharp object, as this will damage the very small jet aperture
and cause the appliance to malfunction. If the jet still does not
function, replace it with a new jet of the correct size. To
re-assemble, reverse the above procedures.The same procedure
applies if the pilot burner jet becomes blocked
4. Check that the flexible hose is completely connected over the
nozzles at each end of the tubing and that it is held firmly in
place by hose clamps. Examine the flexible hose regularly, at
least each time the gas cylinder is changed and ask your dealer
to fit a new LPG hose if it becomes perished, worn or damaged.
5. Only LPG hose that complies with SANS 1156-2 or BS 3212 may
be used with this appliance.
6. Trouble Shooting
•
A normal flame is blue and may have an orange or yellow tip. If
the flame is completely yellow, it may be that the jet is not
securely fitted. Re-tighten to give a gas tight seal. An over-filled
gas cylinder can also cause large yellow flames. Cylinder should
be returned to filling station and checked by weight.
•
Check that the primary air supply apertures in the burners are
clear and free of obstructions.
•
If the flame power drops or the gas will not light, check that the
gas cylinder still contains gas (shake to hear the noise made by
the liquid).If there is still gas,the jet might have become blocked
or partially blocked.
•
If you suspect a blocked jet, follow the instruction in Section 3
above.
3
MODEL: 9 SLICE PANINI NON-STICK GAS TOASTER
Part
SCE
No.
Part No.
1
3-KNOB-TOAST
2
82-ARM-SS-HPOST
3
82-ARM-SS-HFSHD
4
7-PANINI-SPRING
5
14-M5/50-EB-MS
6
7-PAN-BOTTOM-1
7
82-ARM-MS-SSBKT
8
7-FCUP-TOASTER
9
3-GH-FFA3010
10
7-BNR-LPG
11
82-TSG9-SS-BDYAS
12
7-FOOT-FTA7016
13
82-TSG9-MS-BOTCV
14
82-TSG9-HSHLD
15
4-DL-L-AXIS
16
82-TSG9-SS-BBKT
17
7-CS-TSA9209
18
7-BURNER-TSA9209
19
7-MAN-TSA9209-A
20
7-SV-GGA0004
21
82-NGC-SS-MCLMP
22
3-KNOB-APEX
23
3-KI-APEX
24
7-MAN-TSA9209-B
25
7-CV-GGA0004
26
7-JET-TSA9209-LPG
27
7-TC-GGA0004
28
7-REG-ADP
29
3-TOASTER-HAND
30
82-ARM-SS-HAFRT
31
82-ARM-SS-ASSEM
32
6-TOASTER-HS
33
81-TS9-9S-LID
34
6-TOASTER-LS
35
7-PAN-TOP-1
MODEL CODE : TSA9209
REV.1
Description
HANDLE ADJUSTING SCREW
HANDLE HINGE BRACKET
HANDLE FRONT SHIELD
HANDLE SPRING
M5 PLATED EYE BOLT
ALUMINIUM BOTTOM CASTING
SPRING BRACKET
DRIP CUP
8MM GAS HOSE 1 METER LENGTH
BULL NOSE REGULATOR
BODY ASSEMBLY
GRILLER ADJUSTABLE FOOT CASING
BOTTOM COVER GALVANISED
BURNER HEAT SHIELD
DOMED LOGO LARGE ANVIL AXIS
BURNER BRACKET
COOLING SPACER
TSA9209 U BURNER
INLET MANIFOLD
SAFETY VALVE GGA0004
MANIFOLD CLAMP
CONTROL KNOB APEX
CONTROL KNOB INSERT FOR GAS VALVE
FRONT CROSS MANIFOLD
CONTROL VALVE GGA0004
JET
THERMOCOUPLE GGA0004
ANGLE GAS PIPE BRASS CONNECTOR
PLASTIC TOASTER HANDLE
STAINLESS STEEL HANDLE
9 SLICE TOASTER ARM
TOP HINGE AXLE M8
PRESSED TOASTER STAINLESS STEEL LID
M5 HEX SPACERS
ALUMINIUM TOP CASTING PANINI
10
Advertisement
Table of Contents
