Chapter 1: Introduction CAUTION! This UPS series is ONLY intended to be installed in an indoor temperature-controlled environment that is free of conductive contaminants. This UPS series is not intended for use in a computer room Thank you for purchasing this power protection product. It has been as defined in the Standard for the Protection of Electronic Computer/Data designed and manufactured to provide many years of trouble-free service.
Page 4
Manual at any time without obligation to notify any person of such revision or changes. Para Systems will make all possible efforts to NOTE: These UPSs are shipped with the batteries disconnected. The batteries secure the accuracy and the integrity of this Manual. Para Systems must be connected before putting these UPSs into service.
Chapter 2: Controls and Indicators LCD FLOWCHART The following information is available on the LCD screen: CONTROL PANEL 1. Pressing the Enter button saves the changes made to the UPS settings. 2. The Escape button will exit the current screen. 3.
Page 6
The LCD screen's Home Page has four sections: Output Voltage: Set the Battery mode output voltage 120V (Default) / Status 125V. Once set hit the enter key to save the changes. Configuration Event Log Load Shedding: Turn off Load Bank 1 and/or Load Bank 2. Once set About hit the enter key to save the changes.
REAR PANEL Chapter 3: Installation INSTALLATION PLACEMENT This UPS series is ONLY intended to be installed in an indoor temperature- controlled environment that is free of conductive contaminants. DO NOT operate the UPS in extremely dusty and/or unclean areas, locations near heating devices, water, or excessive humidity, or where the UPS is exposed to direct sunlight.
Page 8
CONNECTING THE BATTERY RACKMOUNT CONFIGURATION (QUALIFIED SERVICE PERSONNEL ONLY) This UPS series comes with mounting brackets for the standard 19" Please read all the WARNINGS and CAUTIONS before attempting to connect (46.5cm) rack pre-installed on the UPS. The mounting brackets to fit a 23" the battery.
Page 9
TOWER CONFIGURATION The LCD panel can be rotated to read in the upright position. Use a small The tower configuration allows the user to install the UPS in the upright flat blade screwdriver on the right-hand side of the LCD panel and gently pop out the LCD panel.
CONNECTING YOUR EQUIPMENT POWER MONITORING SOFTWARE Plug the equipment into the output receptacles on the rear panel of the UPS. This UPS series supports Minuteman's SentryHD power monitoring software. Ensure that you do not exceed the maximum output rating of the UPS (refer to the Please go to our website at www.minutemanups.com/minuteman-software- information label or the Electrical Specifications in this manual).
Page 11
NOTE: The input circuit breaker MUST be in the on position for the 208V models. INVERTER (ON-BATTERY) OUTPUT VOLTAGE ADJUSTMENT When a blackout, brownout, or an overvoltage condition occurs; the UPS will transfer The Inverter (On-Battery) output voltage setting can be either 120VAC (208VAC) to the battery mode, the On-Battery icon will illuminate, and the audible alarm will default or 125VAC (240VAC).
Page 12
EXTERNAL BATTERY PACK DETECTION PORT Chapter 5: Configurable Parameters Connecting the External Battery Detection cable from the UPS to the Battery and Settings Pack allows the UPS to automatically detect the External Battery Pack. Once the UPS detects that there is an External Battery Pack connected it will automatically recalculate the estimated runtime based on the number of External (These items may require optional software or hardware) Battery Packs detected and the attached load on the UPS.
PLS check input connection wiring. UPS is overloaded - Check the specifications and remove part of the Para Systems Inc. UPS will shutdown load. If, the UPS shuts down because of an MINUTEMAN UPS Overload, the UPS must perform an Inverter 1809 W.
Chapter 8: Replacing the Battery BATTERY REPLACEMENT PROCEDURE (QUALIFIED SERVICE PERSONNEL ONLY) QUALIFIED SERVICE PERSONNEL ONLY PLEASE READ CAUTIONS WARNINGS BEFORE ATTEMPTING TO REPLACE THE BATTERY MODULE Please read all the WARNINGS and CAUTIONS before attempting to service Hot-swappable batteries mean that the battery modules can be replaced the batteries.
Chapter 9: Specifications Grasp the battery pull tab and gently pull the battery module out of the UPS and set aside. (FIG. 5) NOTE: Use Caution, the battery module is heavy. SYSTEM SPECIFICATIONS Slide the new battery module into the UPS. Reinstall the battery retaining bracket.
Specifications are subject to change without prior notice. No employee, salesman, or agent of Para Systems is authorized to add to or vary the terms of this warranty. Please go to our website at www.minutemanups.com/warranty/ to fill out the Warranty...