Related Manuals for Swatch SWISS TIMING AQUATICS OSB 12
Summary of Contents for Swatch SWISS TIMING AQUATICS OSB 12
- Page 1 OSB 12 Swimming Starting Block User’s Manual 3454.507.02 Version 1.4 Edition March 2020...
- Page 2 Caution and safety precautions Never use any other charger than the supplied or a type approved by Swiss Timing. This could destroy the battery, cause damage to unit, and possible cause personal injury due to fire or/and electrical shock. ...
-
Page 3: Table Of Contents
Swimming Starting Block / OSB12 TABLE OF CONTENTS INTRODUCTION......................1 Construction of the OSB12-RBD starting platform (Relay Break Detection) ....2 Construction of the OSB12 starting platform simple ............2 Fixation material for the platform ................... 3 INSTALLATION ......................4 Fixation of the OSB12 platform .................. -
Page 5: Introduction
Swimming Starting Block / OSB12 1 INTRODUCTION OBS12 presents a powerful new patented feature, revolutionising the way the swimmers start from their blocks. Diving from the starting block with the body propelled by the knee at a 90° angle drastically increases the explosiveness of the start. Physical tests undertaken by top level swimmers showed faster races versus a standard block. -
Page 6: Construction Of The Osb12-Rbd Starting Platform (Relay Break Detection)
1.1 Construction of the OSB12-RBD starting platform (Relay Break Detection) 1. 3454.041 OSB12 Platform 2. 3454.600 RBD (Relay Break Detection) 3. 3393.024 Intermediate plate 1.2 Construction of the OSB12 starting platform simple 1. 3454.041 OSB12 Platform 2. 3454.019 Intermediate plate 3. -
Page 7: Fixation Material For The Platform
Swimming Starting Block / OSB12 1.3 Fixation material for the platform 1. 3454.018 Drilling gauge Drill 8 2. 9051.9806 3. 9039.8579 Pegs M6 x 15 (6x) 4. 9582.1504 Stainless steel washer M6 (6x) 5. 9507.1566 Hexagon head stainless steel screw M6 x 20 (6x) Version 1.4 3454.507.02 Page 3... -
Page 8: Installation
2 INSTALLATION 2.1 Fixation of the OSB12 platform Page 4 3454.507.02 Version 1.4... -
Page 9: Technical Characteristics Of The Osb12-Sw With Relay Break Detection (Rbd) And Without Start Control
Swimming Starting Block / OSB12 3 TECHNICAL CHARACTERISTICS OF THE OSB12-SW WITH RELAY BREAK DETECTION (RBD) AND WITHOUT START CONTROL OSB12-RBD OSB12-Simple DIMENSIONS Plateform 740mm x 520mm x 38mm (165mm with footrest) WEIGHT (KG) 21.2 19.5 Platform white RAL 9010 with non-skidding surface COLOURS dark blue RAL 5002 / RAL 5017 since 2019 Closing at the moment of the... -
Page 10: Control And Maintenance Of The Starting Platform
4 CONTROL AND MAINTENANCE OF THE STARTING PLATFORM 4.1 Control without application of pressure Connect the buzzer to the connection cable. If there is no pressure on the platform (1), the buzzer remains silent. If the buzzer emits a sound, proceed as described in paragraph 4.5. -
Page 11: Service
Swimming Starting Block / OSB12 4.4 Service Once a month: clean the starting platform with soft water and remove the outside sediments of oxidation. Every 6 months: check cable connections. Once a year: check rigidity of platform and footrest fixation. 4.5 Troubleshooting (detection of a short circuit) If the buzzer emits a sound while there is no pressure on the platform, proceed as follows: Unscrew the 4 nuts M8 on the platform (1). -
Page 12: Dismantling Of The Footrest
4.8 Dismantling of the footrest Instruction for dismantling the footrest Unscrew the platform by removing the 6 screws located on the platform. Position the footrest on number 3 to access the screws between the footrest and the guides. Page 8 3454.507.02 Version 1.4... - Page 13 Swimming Starting Block / OSB12 Rotate the top to access the lateral screws. Unscrew the 4 screws (2 on each side). Pull to remove the footrest then remove the guides. To reassemble the footrest, start from this point and follow the instructions backwards. Version 1.4 3454.507.02 Page 9...
-
Page 14: Prevention And Maintenance
PREVENTION AND MAINTENANCE Equipment installed in aquatic complex, often sealed with a high moisture level, require special attention in regards to their maintenance. In fact, the stainless steel parts found on ladders, fences or swimming starting blocks can have corrosion if they are not frequently cleaned. Stainless steel is an excellent product that needs to be very clean to keep its stainless quality. - Page 15 Swimming Starting Block / OSB12 A weekly basic cleaning is required. A thorough cleaning must be done regularly, several times a year. You must use fresh water for cleaning. Never use abrasive material to clean the stainless steel parts. ...
-
Page 16: Appendix
APPENDIX 6.1 Version history Version Date Modifications since last version 05/11/09 Initial version 20/02/14 Addition of chapter 5 Prevention and Maintenance 24/04/14 Correction action force chapter 3, 4.2 and 4.7 26/06/14 Improvement of prevention and maintenance chapter (addition of silicon type B 431) 18/03/20 New blue RAL5017... - Page 17 Swimming Starting Block / OSB12 NOTES Version 1.4 3454.507.02 Page 13...
- Page 19 SWISS TIMING LTD P.O. Box 138, rue de l'Envers 1 Phone +41 32 488 36 11 2606 Corgémont www.swisstiming.com Switzerland info@swisstiming.com SWISS TIMING LTD...
Need help?
Do you have a question about the SWISS TIMING AQUATICS OSB 12 and is the answer not in the manual?
Questions and answers