Subscribe to Our Youtube Channel
Related Manuals for Meccanica Fadini APROLI 480
Summary of Contents for Meccanica Fadini APROLI 480
- Page 1 GB Instructions manual 1 - 16 pages APROLI 480 Oil-hydraulic operator for tilt-up doors with counterbalance EN 13241 EN 12453 EN 12445 the gate opener...
-
Page 2: Installation
CE DECLARATION OF CONFORMITY of the manufacturer: Meccanica Fadini snc (Via Mantova, 177/A - 37053 Cerea - VR - Italy) declares under own responsibility that: APROLI 480 complies with the 2006/42/CE Machinery Directive, and also that it is sold to be installed in an “automatic system”, along with original accessories and components as indicated by the manufacturing company. - Page 3 The operator can be fixed to the door by a specially designed bracket made of galvanized steel along with fitting accessories, galvanized as well. Two types of hardware options are possible with Aproli 480 , either a welding type or a type where no welding is required, which is made possible by components to be assembled together.
-
Page 4: Tools Required For The Installation
ELECTRICAL GENERAL WIRING DIAGRAM AND COMPONENTS LAYOUT Before installing Aproli 480 it is recommended that all of the essential safety and command accessories be prepared. Indicative general layout: it is the installer’s care and responsibility to lay the tubes for the connections in the most suitable way. - Page 5 100 mm, 5/6 mm of thickness, allowing for Aproli 480 fixing bracket to have a stronger support during door operations. Pic. 4 The bracket for the installation of Aproli 480 is to be fixed in the middle of the door. Movement arm of the door...
- Page 6 APROLI 480 Oil-hydraulic operator for tilt-up doors with counterbalance Hardware welding type It is recommended that the Telescopic arms are to be used space between the arms be when there is enough space to 20-25 mm approx. install them next to the existing...
- Page 7 Pic. 8 Proceed now to weld the tubular bar to the telescopic arms, with the door in closed position. To ensure that Aproli 480 can exert a proper hydraulic force on to the door, note the following: the operator is factory preset for mounting a door in closed position;...
- Page 8 Pic. 10 Lateral support to take the tubular bar GREASE GREASE It is recommended that Aproli 480 square shafts be The fastening pins are to be lubricated before being fitted with the tubular bars tightened hard into the cavities Pic. 11...
- Page 9 Once completed all the installation steps and APROLI 480 is fitted correctly onto the door, assess that the movements are performed in a very smooth way without any friction. First make sure that Aproli 480 be released for the first manual test and be well balanced.
- Page 10 Pic. 16 ADJUSTING THRUST POWER Aproli 480 is fitted with screws to control the pressure valves ie. the thrust power to open and close the door. If the door has been properly balanced as explained before, no power adjustment is required.
- Page 11 Pic. 18 INSTALLATIONS WITH PEDESTRIAN DOOR With those installations where a pedestrian door is fitted, two Aproli 480 operators are required and the tubular bars in this case are the shorter type (L = 300 mm). For garage doors with pedestrian access, a NC safety switch is needed and this is to be series connected to terminals 5 and 6 of Elpro 6 exp control board.
- Page 12 APROLI 480 Oil-hydraulic operator for tilt-up doors with counterbalance...
- Page 13 APROLI 480 Oil-hydraulic operator for tilt-up doors with counterbalance...
- Page 14 APROLI 480 Oil-hydraulic operator for tilt-up doors with counterbalance...
-
Page 15: Maintenance Record
APROLI 480 Oil-hydraulic operator for tilt-up doors with counterbalance MAINTENANCE RECORD hand over to the end user of the installation the gate opener Installation address: Maintainer: Date: Installation type: Operator model: Quantity of models installed: Sliding gate Folding door Dimensions per gate leaf:... - Page 16 No. 37/hour Weight of operator 11 kg Annual cycles (with 8 hours of use per day) No. 108.000 Weight of Aproli 480 w/c accessories 24 kg Door surface 7 m² (*) -40 °C with specific optional accessories (Ref. General Catalogue).
Need help?
Do you have a question about the APROLI 480 and is the answer not in the manual?
Questions and answers