Advertisement
Quick Links
12/02/13
U:\Instructions - CURRENT\Lifts\A3 LIFT INST 1265 V FLB.doc
PG. 1 OF 11
PORTA-DOCK, INC.
210A FLB VERTICAL 1265V LIFT W/ GEAR DRIVE WINCH
Thank you for purchasing our product!
Please read these instructions and follow them step by step.*
STEP 1. Separate and group like parts and fasteners together. Locate the winch side member with the longer upright
tube and diagonal braces (REF. # 1). Lay this side member on its side with the corner angles up. Slide the leveling
legs (REF. # 4) into the side member uprights. Secure in place with 1/2" X 3/4" set screws (REF. # 19). Repeat with
the anchor side member.
STEP 2. Locate the two 2 X 2" X 64 1/2" bottom cross tubes (REF. # 5) Using two people stand the side member up
on it's leveling legs. With one person balancing the side member, bolt the bottom cross tube to the corner angles
using 1/2" X 3" bolts, washers, and nuts (REF. # 24, 25, & 26). Leave nuts finger tight.
Advertisement
Related Manuals for Porta-Dock 1265V
Summary of Contents for Porta-Dock 1265V
- Page 1 U:\Instructions - CURRENT\Lifts\A3 LIFT INST 1265 V FLB.doc PG. 1 OF 11 PORTA-DOCK, INC. 210A FLB VERTICAL 1265V LIFT W/ GEAR DRIVE WINCH Thank you for purchasing our product! Please read these instructions and follow them step by step.* STEP 1. Separate and group like parts and fasteners together. Locate the winch side member with the longer upright tube and diagonal braces (REF.
- Page 2 12/02/13 U:\Instructions - CURRENT\Lifts\A3 LIFT INST 1265 V FLB.doc PG 2 OF 11 STEP 3. Locate the 2” X 3” X 68 1/8” top bed cross tubes. The tube with a single cable protruding from each end is the winch bed cross tube (REF. # 6). The other one with the two cables on each end is the anchor cross tube (REF. # 7).
- Page 3 12/02/13 U:\Instructions - CURRENT\Lifts\A3 LIFT INST 1265 V FLB.doc PG 3 OF 11 STEP 5. Bolt the winch to the inside of the winch upright with a 3/8”x 3” bolts, washers, fender washer, and nuts (REF. # 16, 21, 20, & 23) NOTE: the 3/8” fender washer goes against the tube on the top hole only. Find the end of the lift cable, thread the end of the cable through the hole in the side of the winch drum and secure with the cable clip, carriage bolt, and nut.
- Page 4 12/02/13 U:\Instructions - CURRENT\Lifts\A3 LIFT INST 1265 V FLB.doc PG 4 OF 11 STEP 7. Find the four bunk mounting angles (1 ¾” X 1 ¾” X 9” angle with multiple holes), (REF. # 12). Bolt the angles to the bed as shown using 3/8” X 3” X 3 1/6” U-Bolts, washers, & nuts (REF. # 28. 21 & 23). Leave loose at this time.
- Page 5 12/02/13 U:\Instructions - CURRENT\Lifts\A3 LIFT INST 1265 V FLB.doc PG 5 OF 11 STEP 9 Bolt the four diagonal braces (REF. # 14) into the four bottom corners of the lift by placing a 3/8” X 3” bolt and washer (REF. # 16 & 21) thru the round hole of the brace and into the hole of the bottom cross tube and finger tighten with washer &...
- Page 6 12/02/13 U:\Instructions - CURRENT\Lifts\A3 LIFT INST 1265 V FLB.doc PG 6 OF 11...
- Page 7 12/02/13 U:\Instructions - CURRENT\Lifts\A3 LIFT INST 1265 V FLB.doc PG 7 OF 11 210A 1265V FLB VERTICAL LIFT CHAIN DRIVE WINCH REF. # PART NO. DESCRIPTION SIDE MEMBER WINCH SIDE MEMBER ANCHOR 3180 WINCH DL 1200 LEVELING LEG 20032 BOTTOM CROSS TUBE...
- Page 8 REF. # Part # Description Side Bed Tube Left 1265V Side Bed Tube Right 1265V Winch End Bed Cross Tube Sgl Cable 1265V Anchor End Bed Cross Tube Dbl Cable 1265V 3319 2 1/2” Nylon Single Pulley 4317 Brass Spacer Bushing 5092 Hitch Pin 1/8”...
- Page 9 12/02/13 U:\Instructions - CURRENT\Lifts\A3 LIFT INST 1265 V FLB.doc PG 9 OF 11 1265V WINCH & ANCHOR BED CROSS TUBE...
- Page 10 12/02/13 U:\Instructions - CURRENT\Lifts\A3 LIFT INST 1265 V FLB.doc PG 10 of 11 1265V SIDE BED TUBE LEFT & RIGHT...
- Page 11 Porta-Dock, Inc.
Need help?
Do you have a question about the 1265V and is the answer not in the manual?
Questions and answers