Subscribe to Our Youtube Channel
Related Manuals for Melink Positiv
Summary of Contents for Melink Positiv
- Page 1 Installation Manual Revised June 2020 Rev 1.11 Melink Corporation 5140 River Valley Road, Milford, OH 45150 513-965-7300 melinkcorp.com ...
-
Page 2: Table Of Contents
Step 1: Unboxing and Powering On ......................6 Step 2: Location Identification ........................8 Part 2: Configuration, Installation & Calibration Step 3: PositiV Cx App Configuration and Device Installation ............9 Step 4: Calibration ............................15 Troubleshooting & FAQ ..........................16... - Page 3 Before installing PositiV®, it’s important to verify its compatibility with your site. Because PositiV is a wireless, self-powered device, there are certain parameters that must be met for it to be considered a good fit for your facility. Please review the compatibility criteria prior to installation: •...
-
Page 4: Installation Overview
This step consists of configuring the indoor and outdoor PositiV devices and ultimately installing them at the identified locations from Step 2. For this step, the PositiV Cx app will need to be downloaded from the Google Play or App Store, respectively using an Android or Apple device. -
Page 5: Technical Specifications
PositiV Outdoor Unit PositiV Indoor Unit Weight: 0.38 lb. PositiV Outdoor Unit Weight: 1.18 lb. PositiV Indoor Unit Power & Lighting Requirements: 400 lux for 12 hours per day PositiV Indoor Unit Operating Temperature: 0 C — +50 PositiV Outdoor Unit Operating Temperature: -40 C —... -
Page 6: Step 1: Unboxing And Powering On
Pull the clear tab from the top of the indoor unit. This will power on the unit. Once the tab is pulled, tighten the screws on the back of the unit. Unscrew the 5 screws from the back of the outdoor PositiV unit. - Page 7 PositiV Installation Manual Once the screws are removed, pull the front cover from the outdoor unit to expose the inside. Once the cover is separated from the base, place it to the right of the base (solar collector down) as shown in step 1.5.
-
Page 8: Step 2: Location Identification
PositiV Installation Manual Step 2: Location Identification Identify a suitable installation location for the indoor unit. Key compatibility attributes: • Minimal airflow interference • Limited impact from nearby equipment (Radio frequencies, IoT, metal fixtures and equipment, etc.) • Installed away from high-traffic areas where damage from occupants or employees could occur •... - Page 9 PositiV Installation Manual Step 3: PositiV Cx App and Configuration During this step, the installer will be using his or her phone to configure the PositiV system. During configuration, the installer will enable Bluetooth communication between the devices; sync the devices; range test the connectivity strength between the indoor and outdoor PositiV units;...
- Page 10 The cover is tight enough when there is no longer a gap between the base and cover. Do not overtighten. With the units still next to each other, press and release the Bluetooth button on the indoor unit. On your phone, turn Bluetooth “On” and open the PositiV Cx app.
- Page 11 PositiV Installation Manual A. When prompted to “Choose a Device”, select the PositiV device with a serial number (S/N) that matches the serial number on the back of the outdoor unit (circled in blue). B. Chose the option “Cell Diagnostics”. Then, when asked to “Enter the Pair Code,” enter the BLE # on the back of the outdoor unit (circled in green).
- Page 12 Note: The indoor unit label is found behind the backplate on the indoor unit. The PositiV system may take up to a minute to be located on the app...
- Page 13 3.10 On your phone, select “RSSI Test.” You will then be prompted to “Enter Pair Code.” Enter the BLE# found on the back of your indoor PositiV unit (circled). 3.11 You should now see that the selected device is connected. Begin the RSSI test. Verify that the connection between the units is greater than -95 dBi.
- Page 14 PositiV Installation Manual 3.12 With both units, walk to the desired installation location of the outdoor unit. Mount the outdoor unit by either (a.) banding the unit to an exhaust vent using the provided pipe clamp, (b.) screwing the unit to an RTU / air handling equipment, or (c.) screwing the unit to concrete or masonry.
- Page 15 3.17 Once the indoor and outdoor PositiV units are mounted, click into the “Properties” tab and select the “ALL” option to set up site name, store number, address, block, city,...
-
Page 16: Step 4: Calibration
Click “Pressure Calibration” on the PositiV Cx app. Follow the steps as described on the PositiV Cx app. After calibration has completed, clip the indoor unit to the backplate as shown. Hook Backplate Please note the correct orientation of the PositiV indoor unit in the image above. -
Page 17: Troubleshooting & Faq
What do I do if my PositiV system does not show up when I open the PositiV Cx app? Verify that Bluetooth is enabled on your phone. Then, close and reopen the app. It may take up to a minute for the PositiV units to appear on the app.
Need help?
Do you have a question about the Positiv and is the answer not in the manual?
Questions and answers