Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Varytec Hero Beam 100
Summary of Contents for Varytec Hero Beam 100
- Page 1 Hero Beam 100 moving head...
- Page 2 Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de 21.04.2021, ID: 477540...
-
Page 3: Table Of Contents
7.6 Gobos..........................25 7.7 Menu overview......................26 7.8 Functions in 6-channel DMX mode................ 26 7.9 Functions in 19-channel DMX mode..............28 Technical specifications....................32 Plug and connection assignment................. 34 Troubleshooting........................35 Cleaning............................ 36 Protecting the environment................... 37 Hero Beam 100 moving head... - Page 4 Hero Beam 100 moving head...
-
Page 5: General Information
The letterings for connectors and controls are marked by square brackets and italics. Examples: [VOLUME] control, [Mono] button. Displays Texts and values displayed on the device are marked by quotation marks and italics. Examples: ‘24ch’ , ‘OFF’ . Hero Beam 100 moving head... -
Page 6: Symbols And Signal Words
This combination of symbol and signal word indicates a possible dangerous situation that can result in mate‐ rial and environmental damage if it is not avoided. Warning signs Type of danger Warning – high-voltage. Warning – dangerous optical radiation. Hero Beam 100 moving head... - Page 7 General information Warning signs Type of danger Warning – suspended load. Warning – danger zone. Hero Beam 100 moving head...
-
Page 8: Safety Instructions
The load capacity of trusses or other fixtures must be suffi‐ cient for the intended number of devices. Not that the movement of the head places additional loads on the load-bearing parts. Hero Beam 100 moving head... - Page 9 NOTICE! Possible damage due to installation of a wrong fuse The use of different types of fuses can cause serious damage to the unit. Fire hazard! Only fuses of the same type may be used. Hero Beam 100 moving head...
-
Page 10: Features
For technological reasons, the light output of LEDs decreases over their lifetime. This effect increases with higher operating temperature. You can extend the service life of the illuminants by providing adequate ventilation and operating the LEDs with the lowest possible brightness. Hero Beam 100 moving head... -
Page 11: Installation
Possible data transmission errors For error-free operation make use of dedicated DMX cables and do not use ordinary microphone cables. Never connect the DMX input or output to audio devices such as mixers or amplifiers. Hero Beam 100 moving head... - Page 12 Safety cables are being threaded through the safety eyelets (B) on the bottom side of the housing. Please note that this device must not be connected to a dimmer. Hero Beam 100 moving head...
-
Page 13: Starting Up
Connect the DMX output of the master device to the DMX input of the first slave device. Then connect the DMX output of the first slave device to the DMX input of the second slave device and so Hero Beam 100 moving head... -
Page 14: Connections And Controls
Closes an open submenu without saving any changes. 8 [DMX In] DMX input, designed as XLR panel plug, 3-pin 9 [DMX Out] DMX output, designed as XLR panel socket, 3-pin 10 [DMX In] DMX input, designed as XLR panel plug, 5-pin Hero Beam 100 moving head... - Page 15 DMX output, designed as XLR panel socket, 5-pin 12 Fuse holder 13 [Power In] Lockable input socket (Power Twist) for mains power supply 14 [Power Out] Lockable output socket (Power Twist) for powering a connected device Output current 12 A max. Hero Beam 100 moving head...
-
Page 16: Operating
If you don't press any button for 60 seconds the display turns off. A short press on [ESC], [SET], [UP] or [DOWN] will then turn it back on. All previous settings are retained even when you switch the device off and discon‐ nect it from the mains. Hero Beam 100 moving head... -
Page 17: Operating Modes
Press [UP] or [DOWN] to select the desired DMX mode and confirm the selec‐ tion with [SET]. The following DMX modes are available: Menu level 2 Description ‘DMX 6CH mode’ 6-channel mode ‘DMX 19CH Mode’ 19-channel mode Hero Beam 100 moving head... - Page 18 To use a device as the master device, select one of the automatic programmes, acti‐ vate the sound control or the manual control. Connect the slave devices to the DMX output of the master device and select the DMX mode. Hero Beam 100 moving head...
- Page 19 ‘0’ … ‘255’ ‘gobo flow Speed for gobo pass counterclock‐ backward’ wise, increasing speed ‘0’ … ‘255’ ‘Frost’ ‘ ON’ Activating frost filter ‘ OFF’ Deactivating frost filter ‘7 color wheel’ ‘ ON’ Activating colour wheel effect Hero Beam 100 moving head...
- Page 20 Deactivating rotation of the linear rotation’ prism ‘Forward’ Setting the rotation speed of the linear prism clockwise, increasing ‘0’ … ‘255’ speed ‘Backward’ Setting the rotation speed of the linear prism counterclockwise, ‘0’ … ‘255’ increasing speed Hero Beam 100 moving head...
-
Page 21: Settings
Blackout on DMX failure ‘Auto Mode’ Automatic programmes mode on DMX failure ‘Manual Control’ Manual mode on DMX failure ‘Sound Mode’ Sound control on DMX failure ‘Dimmer Curve’ Setting the dimmer curve ‘Linear’ linear proportional course Hero Beam 100 moving head... - Page 22 Backlight’ ‘ON’ Illumination permanently on ‘OFF’ Illumination is switched off after 60 seconds ‘Display Reverse’ Display reversal ‘ON’ Text in the display appears upside down ‘OFF’ Text in the display appears normal ‘Autolock’ Key lock Hero Beam 100 moving head...
- Page 23 ‘OFF’ automatic lock switched off ‘Reset Motor’ Resetting the motor ‘YES’ Motor reset ‘NO’ no motor reset ‘Factory Reset’ Reset to factory defaults ‘YES’ Reset to factory defaults ‘NO’ no reset to factory defaults Hero Beam 100 moving head...
- Page 24 Specifying the initial effect wheel setting ‘Focus’ ‘–128’ … ‘127’ Specifying the initial focus setting ‘Prism circular’ ‘–128’ … ‘127’ Specifying the initial circular prism setting ‘Prism linear’ ‘–128’ … ‘127’ Specifying the initial linear prism setting Hero Beam 100 moving head...
-
Page 25: System Information
‘Current Mode’ Displays the current operating mode. ‘Temperature Displays the current head temperature. Head’ ‘Temperature Displays the current temperature of the device base. Base’ ‘Software Version’ Displays the current software version. 7.6 Gobos Static Gobo wheel Hero Beam 100 moving head... -
Page 26: Menu Overview
Rotation (pan) (0° up to the maximum value of the Pan range) 0…255 Inclination (tilt) (0° up to the maximum value of the Tilt area) 0…255 Dimmer intensity from dark (0) to bright (255) Stroboscope Hero Beam 100 moving head... - Page 27 Pan-Tilt auto programme 3 85…110 Pan-Tilt auto programme 4 111…136 Pan-Tilt auto programme 5 137…162 Pan-Tilt auto programme 6 163…188 Pan-Tilt auto programme 7 189…214 Pan-Tilt auto programme 8 215…255 Sound control Pan and Tilt Hero Beam 100 moving head...
-
Page 28: Functions In 19-Channel Dmx Mode
Orange / light blue 30…34 Bright blue 35…39 Light blue / green 40…44 Green 45…49 Green / yellow 50…54 Yellow 55…59 Yellow / pink 60…64 Pink 65…69 Pink / blue 70…74 Blue 75…79 Blue / pink 80…84 Pink Hero Beam 100 moving head... - Page 29 Gobo 8 90…99 Gobo 9 100…109 Gobo 10 110…119 Gobo 11 120…127 Gobo 1 shake, increasing speed 128…135 Gobo 2 shake, increasing speed 136…143 Gobo 3 shake, increasing speed 144…151 Gobo 4 shake, increasing speed Hero Beam 100 moving head...
- Page 30 Linear prism activated Linear prism rotation 0…63 0…400° 64…126 Rotation clockwise, decreasing speed 127…128 Stop rotation 129…191 Gobo wheel rotation counterclockwise, increasing speed 192…255 Circular rotation, increasing speed Frost filter 0…127 No function 128…255 Frost filter activated Hero Beam 100 moving head...
- Page 31 Reset of the effects motor, if the value is transmitted for at least 3 seconds 77…128 Reset of the Pan / Tilt motor, if the value is transmitted for at least 3 seconds 129…255 Reset, if the value is transmitted for at least 3 seconds Hero Beam 100 moving head...
-
Page 32: Technical Specifications
IP20 Mounting options hanging, standing Dimensions (W × H × D) 303 mm × 465 mm × 188 mm Weight 13.0 kg Ambient conditions Temperature range 0 °C…40 °C Relative humidity 20 %…80 % (non-condensing) Hero Beam 100 moving head... - Page 33 Technical specifications Further information Type Beam Colour mixture Colour wheel Number of colour wheels Gobo wheel, static Gobos Rotating gobos Motorized focus Motorized zoom Prism Iris Hero Beam 100 moving head...
-
Page 34: Plug And Connection Assignment
A five-pin XLR socket serves as DMX output, a five-pin XLR plug serves as DMX input. The drawing below and the table show the pin assignment of a matching coupling. Assignment Ground (shielding) Signal inverted (DMX–, ‘cold’) Signal (DMX+, ‘hot’) unused / second connection (DMX–) unused / second connection (DMX+) Hero Beam 100 moving head... -
Page 35: Troubleshooting
DMX interface circuit. If the procedures recommended above do not succeed, please contact our Service Center. You can find the contact information at www.thomann.de. Hero Beam 100 moving head... -
Page 36: Cleaning
Before cleaning, switch off the device and disconnect mains-oper‐ ated devices from the mains. Only use pH-neutral, solvent-free and non-abrasive cleaning agents. Clean the unit with a slightly damp lint-free cloth. Hero Beam 100 moving head... -
Page 37: Protecting The Environment
Dispose of this device through an approved waste disposal firm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility. Hero Beam 100 moving head... - Page 38 Notes Hero Beam 100 moving head...
- Page 40 Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.de...