Advertisement
Quick Links
WARNING: Because of the possible danger to persons(s) or property from accidents which may result from the improper use of products,
it is important that correct procedures be followed: Products must be used in accordance with the engineering information specified in the
catalog. Proper installation, maintenance and operation procedures must be observed. The instructions in the instruction manuals must be
followed. Inspections should be made as necessary to assure safe operation under prevailing conditions. Proper guards and other suitable
safety devices or procedures as may be desirable or as may be specified in safety codes should be provided, and are neither provided by
Baldor Electric Company nor are the responsibility of Baldor Electric Company. This unit and its associated equipment must be installed,
adjusted and maintained by qualified personnel who are familiar with the construction and operation of all equipment in the system and the
potential hazards involved. When risk to persons or property may be involved, a holding device must be an integral part of the driven
equipment beyond the speed reducer output shaft.
www.baldor.com www.ptplace.com
Baldor Electric Company Headquarters
P.O. Box 2400, Fort Smith, AR 72902-2400 U.S.A., Ph: (1) 479.648.5792, Fax (1) 479.648.5792, International Fax (1) 479.648.5895
DODGE/Reliance Division
6040 Ponders Court, Greenville, SC 29615-4617 U.S.A., Ph: (1) 864.297.4800, FAX: (1) 864.281.2433
Copyright © 2007 Baldor Electric Company
04/07
Parts Replacement Manual
HYDROIL
TORQUE-ARM
Speed Reducers
Taper Bushed
For Char-Lynn H, S, T and 2000 Series
6B Spline Motors
SIZES: HXT305A
www.dodge-pt.com
All Rights Reserved. Printed in USA.
1M-K
For
HXT405A
HXT505A
www.reliance.com
This material is not intended to provide operational instructions. Appropriate instruction
manuals and precautions should be studied prior to installation, operation or maintenance
of equipment.
Advertisement
Related Manuals for Dodge HXT305A
Summary of Contents for Dodge HXT305A
- Page 1 Speed Reducers Taper Bushed For Char-Lynn H, S, T and 2000 Series 6B Spline Motors SIZES: HXT305A HXT405A HXT505A WARNING: Because of the possible danger to persons(s) or property from accidents which may result from the improper use of products, it is important that correct procedures be followed: Products must be used in accordance with the engineering information specified in the catalog.
- Page 3 REDUCER INSTALLATION The running position of the reducer in a horizontal application is not limited to the four 1. On sizes HXT305A, HXT405A, and HXT505A use positions shown in Figure 1. However, if running lifting lug to lift reducers. position is over 20º either way from sketches, the oil level, plug cannot be safely used to check the 2.
- Page 4 Quarts Ounces Quarts Ounces Quarts Ounces Quarts (Approx) (Approx) (Approx) (Approx) (Approx) (Approx) (Approx) (Approx) (Approx) (Approx) (Approx) (Approx) HXT305A 1½ 1.42 1.30 1.30 HXT405A 1½ 1.42 2¼ 2.13 2.01 1.77 HXT505A 3.19 4¼ 4.02 3.67 3¾ 3.54 † Refer to Fig. 1 on page 2 for mounting positions.
- Page 5 Note: The two-digit numbers are for reference only. Order parts by the six-digit numbers in the Parts List. Each six-digit number is a complete identification of the part or assembly.
- Page 6 419047 Recommended spare parts Includes parts listed immediately below marked “ .” HXT505A housing ß On size HXT305A for 1 " thru 1¾" bores; HXT405A for 1 " thru assembly also includes a two-piece housing. Bushing assemblies include 2 " bores; HXT505A for 1 "...
-
Page 7: Ordering Parts
REPLACEMENT OF PARTS A DODGE TORQUE-ARM Speed Reducer can be WARNING disassembled and reassembled by careful attention to External loads may cause machine movement. the instructions following, using tools normally found Block machine before removing any drive train in a maintenance department. - Page 8 7. Using the same procedure as in step 6, adjust the input shaft bearings, except the axial end play should be .002" to .004". Table 7 — Bolt Tightening Torque Values Reducer Housing Bolts Seal Carrier Bolts Size (in.-lbs.) (in.-lbs.) HXT305A HXT405A HXT505A...
- Page 9 Viscosity Classification Equivalents...