Larson Electronics DCP-16-DP-HD Instruction Manual

Waterproof Transformer Converts 120V-277V AC to 12/24 Volts DC
Thank you for your purchase of the Larson Electronics DCP-16-DP-HD.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
• INSTALLATION SHOULD ONLY BE CONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
• RISK OF FIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IF NOT QUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
• BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•
TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
•
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY
REFERENCE. THE
ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS PRODUCT.
IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET, CONSULT AN
ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK – DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING. RISK
OF PERSONAL INJURY – FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY. RISK
OF BURN – ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OF THIS DEVICE.
CORD IS INTENDED TO ALLOW OPERATORS TO EXTEND POWER TO EQUIPMENT WHEN STATIONARY OUTLETS ARE NOT
READILY AVAILABLE.
IMPROPER USE OF THIS CORD, PLUG, AND RECEPTACLE CAN LEAD TO SERIOUS INJURIES OR DEATH TO
PERSONNEL.
PERIODIC INSPECTION OF THE CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND,
THE CORD MUST BE REPLACED BEFORE RESUMING USE.
The Larson Electronics DCP-16-DP-HD Waterproof Power Supply converts commonly used 120-240VAC electrical current to 12VDC
@16 Amps. This converter includes a typical straight blade plug on the input end and a 2 prong Deutsch connector on the output end.
This unit takes voltages within the 100-277VAC range and reduces it to 12 VDC or 24 VDC, allowing users to use standard AC power to
operate equipment like our LED light bars and HID Golights that require low voltage DC current.
WIRING
Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product, in all locations especially in outdoor areas
where weatherproofing may be required. Universal voltage driver permits operation at 12V DC or 24V DC.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown in the diagram 
Secure each pair of wires according to the diagram. Utilize a junction box or similar
take precautionary steps
water may come in contact with the unit. Ensure the unit is properly grounded and that wiring is done
according to all local and national electrical/building codes.
Larson Electronics, LLC
16 Amps - Straight Blade Wall Plug
Instruction Manual
BEFORE INSTALLING
DCP-16-DP-HD MUST
for weatherproofing all
Phone: (800) 369-6671
THIS FIXTURE. SAVE
BE WIRED
connections if installed in a location where
Fax: (903) 498-3364
THESE INSTRUCTIONS
IN ACCORDANCE
device and
www.larsonelectronics.com
DCP-16-DP-HD
FOR FUTURE
WITH NATIONAL
THIS LINE
1 of 2