Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Labconco Goldfisch Fat Extraction
Summary of Contents for Labconco Goldfisch Fat Extraction
- Page 1 Goldfisch Fat Extraction Apparatus Models 3500100...
- Page 2 The warranty for the Goldfisch Fat Extraction Apparatus will expire one year from date of installation or two years from date of shipment from Labconco, whichever is sooner. Warranty is non-transferable and only applies to the owner (organization) of record.
-
Page 3: Table Of Contents
CHAPTER 1: INTRODUCTION Components Shipped General Description Component Identification CHAPTER 2: INSTALLATION Preparation Location Utility Connections Initial Start-Up and Check Out Gasket Assembly CHAPTER 3: NORMAL OPERATION & ROUTINE MAINTENANCE Summary of Operation Procedures Maintenance APPENDIX A: REPLACEMENT PARTS APPENDIX B: DIMENSIONS APPENDIX C: SPECIFICATIONS APPENDIX D: WIRING DIAGRAM... -
Page 4: Chapter 1: Introduction
As shipped, the carton should contain the following: Part Number Description 35001 Goldfisch Fat Extraction Apparatus 35051 Beakers, 100 cc (12) 35049 Sample Tubes (6) 35048... -
Page 5: General Description
Chapter 1: Introduction General Description The Labconco Goldfisch Fat Extraction Apparatus is designed for single or multiple fat extractions according to the methods prescribed in the Association of Official Analytical Chemists (AOAC) or other technical methods involved with the use of a continuous extractor. - Page 6 Chapter 1: Introduction Figure 1 Product Service 1-800-522-7658...
-
Page 7: Chapter 2: Installation
Preparation The Goldfisch Extractor is shipped complete and fully assembled. The operating parts shipped with the unit will be installed after the unit has been located in the laboratory area. Location Choose a location in the laboratory which has a convenient 115 volt A.C. outlet, an unrestricted 3/8"... -
Page 8: Gasket Assembly
Chapter 2: Installation Gasket Assembly Remove contents of the operating parts package which should be taped to the unit. Assemble the gasket, wave washer, retaining ring and glassware according to assembly drawing instructions as shown in Appendix A. Hand tighten the retaining rings to achieve vapor seal. -
Page 9: Summary Of Operation
& & Summary of Operation The Labconco extractor reduces extraction time from 16 hours to about four hours through its efficient refluxing system. The operation is carried out by ® using a Pyrex beaker as the solvent chamber. The procedure involves placing the samples between the boiling solvent and a cold surface. -
Page 10: Chapter 3: Normal Operation & Routine Maintenance
Chapter 3: Normal Operation & Routine Maintenance Place solvent of proper type and quantity into beaker. A quantity of 25 to 35 ml of solvent is normally sufficient for an estimate 3 to 4 hours of refluxing. Assemble beaker to retainer ring with the wave washer inserted and twist to lock securely in place. -
Page 11: Maintenance
Use covers when removing or attaching beakers to condenser heads. (15) The Labconco Fat Extractors are suitable for carrying out the indirect Method of Fat Extraction (also known as “Crude Fat Extraction”). This procedure requires the determination of moisture, followed by extraction of the dried material, with the loss reported as the ether extract. -
Page 12: Appendix A: Replacement Parts
6 Req’d. Wave washer – Beaker seal 35191 35120 Spring, compression heater push rod 35172 Condenser assembly *Not furnished as standard equipment, but offered as an accessory. Note: When ordering replacement parts, specify the Labconco equipment serial number. Product Service 1-800-522-7658... - Page 13 Appendix A: Replacement Parts Product Service 1-800-522-7658...
-
Page 14: Appendix B: Dimensions
35.7" 26.9" 9" Product Service 1-800-522-7658... -
Page 15: Appendix C: Specifications
6-unit Goldfisch Fat Extractor Model No. 35001 operates on 115 volts, 50/60 Hz, (max.) at 5.2 amps. It is shipped complete with power cord and grounded (3 wire) plug. Standard features are as follows: 1. Main power on-off. 2. Full range variable heat control switch. Each switch controls two heaters. 3. -
Page 16: Appendix D: Wiring Diagram
Product Service 1-800-522-7658...
Need help?
Do you have a question about the Goldfisch Fat Extraction and is the answer not in the manual?
Questions and answers