1. Manuals
  2. Brands
  3. Koukaam Manuals
  4. Accessories
  5. NETIO-230B
  6. Instruction manual

Koukaam netio-230B Instruction Manual

Hide thumbs Also See for netio-230B:
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the netio-230B and is the answer not in the manual?

Questions and answers

Related Manuals for Koukaam netio-230B

Summary of Contents for Koukaam netio-230B

  • Page 2 Warning Unauthorized modification of this device can cause its damage! The manufacturer is not responsible for possible damage caused by improper usage or usage in unsuitable environment. Device has been designed for indoor use only. Do not use the device during the strong vibrations. If your device does not work properly, please contact your local dealer.

  • Page 3: Table Of Contents

    Contents 1 Introduction 1.1 Features ..........1.2 Specifications .

  • Page 4: Introduction

    1 Introduction NETIO-230B is a power controller device that can be controlled remotely via Internet browser, Telnet, or CGI commands. Thanks to the network management technology based on the IP protocol the user can easily control or check power status of his devices (appliances) using the computer connected to local network or the Internet.

  • Page 5: Minimum System Requirements

    Latency: 300x60x90 mm (WxHxL) Network interface:10/100 Mbit/s 1.3 Minimum System Requirements Computer with installed Internet browser (Microsoft Internet Explorer, Opera, Mozilla Firefox, . . . ) 2 Interface Description 2.1 Side View Figure 1: side view 1. Fuse housing for main fuse 2.

  • Page 6: Installation

    Before the first use, please make sure that: the power supply is 230 V AC. 3.1 Hardware connection of the device 1. Connect your NETIO-230B to the computer network (switch, router) using the Ethernet cable with RJ-45 connectors. Use cross cable when the device is directly connected to the PC.
  • Page 7 Figure 3: device set-up 3. Choose the proper device from the list and click Device setup. Window appears for set-up of network parameters - IP address, Subnet mask and Gateway. (Fig- ure 4) Figure 4: set-up of network parameters After input of requested changes based on your network environment, click Change IP. Changes are made to the device settings.

  • Page 8: Operation And Settings

    Click on Manual Control the Menu on the left side. Output Manual control page will show up.(figure 6) NETIO-230B can control all four outputs at the same time. Choose which ports should be turned ON/OFF and click Apply. If you would like only to restart the devices connected to the specific ports, tick Interrupt and then click Apply.

  • Page 9: Output Status And Configuration

    Figure 6: manual control not, the device does not accept manual output control requests and only scheduled switching and the Watchdog feature are in operation. PressingAll off button will turn all outputs OFF. 5.1.2 Output status and configuration On the left side of the window, click Status & configuration, the list of ports and status information appears in the right window.
  • Page 10 Figure 7: set-up ports Figure 8: output configuration...

  • Page 11: System Configuration

    event will be triggered once per week. ON time: date and time for switching the output ON, if you select DAILY mode, this is the date and time of first execution OFF time: Date and time to switch the output OFF. If you select the DAILY mode, this is the date and time of first execution Week schedule: Select in which weekdays the Timer control should be in operation.

  • Page 12: Configuration Of Network Parameters

    5.2.1 Configuration of network parameters Click Configuration link in the menu to change the system configuration. Here, you can set up IP Address, Subnet Mask, Default Gateway and DNS Server according to your network parameters. If you do not wish to setup the network parameters manually, you can Enable DHCP to obtain requested parameters automatically from the DHCP server in your network.

  • Page 13: Date And Time Settings

    Click Date & time in the menu and the system date and time settings will appear on the right. NETIO-230B supports two methods of getting the right date and time values. It can be entered manually or obtained automatically from the SNTP server.

  • Page 14: Manage Users

    Synchronized: time successfully synchronized with SNTP server Not Synchronized: time successfully synchronized with SNTP server Local time offset: Manual set-up of your time zone – time shift against GMT time in minutes. Daylight saving time: Enables daylight saving time. Daylight saving time start: Daylight saving time begin Daylight saving time end : Daylight saving time end Local time: mManual local time set-up with SNTP server synchronization off.

  • Page 15: Firmware Update

    Remove: removal of the selected user 5.2.5 Firmware update The page Firmware Update is used to upload the new firmware into your NETIO-230B. After you click the Firmware Update link in the menu, a warning message will appear on the right.

  • Page 16: Communication Via Kshell Interface

    . It is 128-bit number transmitted as 32-digit hexadecimal number. 5.3.2 Communication via KSHELL interface To connect to your NETIO-230B please follow these steps: 1. Open command prompt 2. Enter the command telnet 192.168.10.100 1234 (replace the address with the address of your...

  • Page 17: List Of Commands For Control Via Kshell

    If you entered correct name and password the device should reply 250 OK. Now you are logged in and you can use commands to control your NETIO-230B. Each communication session via KSHELL interface has limited validity. In case of no response for about one minute, the session is terminated automatically.
  • Page 18 Example: Command port list 01ui will turn output 1 OFF, turn output 2 ON, output 3 will remain unchanged and output 4 will be interrupted for a short while. port setup output [ output name mod:manual/timer interrupt delay PON status ] Command for change of output parameters - significance of parameters is as follows: output name - Entered in quotation marks (also without them if it does not contain whites- paces).
  • Page 19 wd ip addr - IP address of monitored device in seconds wd timeout - maximum response time of monitored device wd POn delay - Time (in seconds) for which the Watchdog feature will be inactive after output restart. During this interval, the monitored device should recover to its normal opera- tion after being restarted.

  • Page 20: Cgi Commands

    5.3.4 CGI commands NETIO-230B can easily be integrated into your applications using CGI commands. CGI command device control uses the following command format: http:// IPaddress /tgi/control.tgi? command Replace the IP address of your device with the string IP address .

  • Page 21: Manual Control

    html 553 INVALID LOGIN /html - Incorrect user name / password. html 554 ALREADY LOGGED IN /html - You are trying to log in although you are already logged in. quit= quit Logout. Return value is html 110 BYE /html . port=list / xxxx Parameter list shows output status in the format html port1 port2 port3 port4...

  • Page 22: Firmware Upgrade Problem

    5.2.5. 5.6.3 Fuse replacement If your NETIO-230B will not work and the main switch is not lighted, it is possible that the fuse has blown. Before you proceed to fuse replacement, check whether the NETIO-230B device is TURNED OFF and DISCONNECTED FROM THE NETWORK.

Table of Contents