Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Dell Manuals
  4. Storage
  5. EMC Unity
  6. Quick start manual

Dell EMC Unity Quick Start Manual

Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
EMC Unity
Before you begin
Required:
Create an EMC Online Support account:
❑
https://support.emc.com. You will need this
account later in the installation process to
activate software licenses and configure ESRS
(EMC Secure Remote Services).
If your Unity system arrived pre-racked, begin
❑
installation at Step 4 of this guide.
Obtain the help of a second person to install
❑
the enclosure into the rack, or use a mechanical
lift.
If you have more than one enclosure to install,
❑
Unity Installation Guide
use the
your installation. The installation guide
includes racking and cabling instructions
required for additional enclosures, which are
not covered here. The
is located here: http://bit.ly/unityinfohub.
Purpose of this document
Management
™
Quick Start
to complete
Unity Installation Guide
Launch
Unisphere
8
Assign
7
Address
6
Power Up
Recommended:
Download the Connection Utility at
❑
unityinfohub. You will need this utility if you want to
assign static IP addresses to your system. You will not
need this utility if you plan to use DHCP to
automatically assign IP addresses to your system.
If you are installing your system in a location with
❑
restricted internet access, download the Connection
Utility and your license files before starting the
installation process: http://bit.ly/unityinfohub.
Watch the Unity Quick Start Installation video:
❑
bit.ly/unityinfohub.
What's next
Refer to the
section for important details
❑
about adding enclosures and using the Unisphere
online help.
Unpack
1
Install
Rails
2
3
4
Record SN
5
Cable to
Network
Copyright © 2016 EMC. All rights reserved. P/N 300-000-228 Rev 02
http://bit.ly/
http://
Install
System
>

Advertisement

loading

Related Manuals for Dell EMC Unity

Summary of Contents for Dell EMC Unity

  • Page 1 ™ EMC Unity Quick Start > Before you begin Required: Recommended: Create an EMC Online Support account: Download the Connection Utility at http://bit.ly/ ❑ ❑ https://support.emc.com. You will need this unityinfohub. You will need this utility if you want to account later in the installation process to assign static IP addresses to your system.

  • Page 2: Unpack Your System

    > 1. Unpack your system Verify that you have the following components: 2U Disk Processor Enclosure (DPE) with either 12-3.5” drive slots or 25-2.5” drive slots ❑ Rail kit, including 2 rails with 6 mounting screws ❑ 2 power cables (100-240Vac) ❑...
  • Page 3 > 4. From the rear of the cabinet, secure the rails in place using one M5 screw on each rail: Right Rail Left Rail (viewed from rear) (viewed from rear) CL5775 5. Next, working from the front of the cabinet, align the adaptor with the mounting hole on the front of the rack, as shown in the image below in Step 6.
  • Page 4 > 3. Install the system onto the rails CAUTION The enclosure is heavy and should be installed into or removed from a rack by two people. To avoid personal injury and/or damage to the equipment, do not attempt to lift and install the enclosure into a rack without a mechanical lift and/or help from another person.
  • Page 5 > 4. Record your system serial number Locate and record the product serial number tag on the front of the DPE chassis in either of the locations shown below. You will use this number to obtain product licenses later in the installation process: 12-drive enclosure: The underside of the top edge 25-drive enclosure: Below the power status LED near the right side.
  • Page 6 > 6. Power up 1. Verify that the cabinet’s circuit breakers are in the ON position and power is connected to the cabinet. 2. Connect each DPE power cable to the system power component and to the PDUs. After you plug in the power cables, the system immediately powers up: 3.

  • Page 7: What's Next

    Note: If you receive a certificate error when trying to access Unisphere, refer to your internet browser instructions to either bypass the error or to install the self-signed array certificate. For more detail EMC Unity Family Security Configuration Guide about your system certificate, refer to the •...
  • Page 8 > Copyright © 2016 EMC. All rights reserved. P/N 300-000-228 Rev 02...
  • Page 9 Copyright © 2015 EMC Corporation. All rights reserved. Published in USA. EMC believes the information in this publication is accurate as of its publication date. The information is subject to change without notice. The information in this publication is provided as is. EMC Corporation makes no representations or warranties of any kind with respect to the information in this publication, and specifically disclaims implied warranties of merchantability or fitness for a particular purpose.