C-HR
ZYX10
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD FRONT HALF SPOILER FOR TOYOTA ZYX10 C-HR.
PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION.
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
ATTENTION
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
FRONT HALF SPOILER
【BEFORE PAINTING】
1) Temporarily install WALD Front Spoiler to the body.
※ Adjust the details of WALD Front Half Spoiler to fit the body by rasps or sandpapers.
2) Mark the location of the holes for the attached tapping screws after checking the balance.
3) Take off WALD Front Half Spoiler, then make holes according to the marked positions.
4) Paint WALD Front Half Spoiler according to the picture.
【AFTER PAINTING】
5) Completely degrease the installation position,
then use calking glue to install WALD Front Half Spoiler to the body.
6) Fix the attached brackets and rubber moldings on WALD Front Half Spoiler.
7) Temporarily install WALD Front Spoiler to the body with the attached double-sided tape.
※ Fold the both ends of release paper to adjust the location.
8) Check all the details of the fitment, then tighten the attached bolts.
9) Fix the attached chrome accents on WALD Front Half Spoiler with the double-sided tape and caulking glue.
10) Leave it till completely fixed.
※WALD SHOWCAR IS PAINTED LIKE THE PICTURE (STEP 4)
MATTE BLACK
MATTE BLACK
ATTENTION
※ MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK. DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ DEGREASE ALL THE INSTALLATION POSITIONS, AND REMOVE THE BODY PROTECTION COATING BEFORE THE INSTALLATION.
※ ADJUST ALL THE DETAILS OF OUR PRODUCTS TO FIT ON A CAR PERFECTLY.
WALD. INTERNATIONAL
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
(2017y )
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
■HOW TO FIX THE ATTACHED
RUBBER MOLDINGS (STEP 6)
Priming the surface,
then fix the attached
rubber moldings.
RUBBER MOLDING
ADHESIVE SURFACE
BRACKET
ATTACHED BOLTS
(M5 X 15)
ATTACHED BOLTS
(M5 X 15)
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
INSTALLATION MANUAL
FRONT SPOILER
FRONT HALF SPOILER
CHROME ACCENTS
RUBBER MOLDING
TAPPING SCREWS (M5 X 16)
BRACKETS
BOLTS (M5 X 15)
Use caulking glue
to fill the gap
between the product
and the body.
ATTACHED
DOUBLE-SIDED TAPE
OEM BOLTS
OEM BOLTS
NEED TO ADJUST WITH THE BODY LINE CAREFULLY
CHROME ACCENT
※USE CAULKING GLUE AND ATTACHED DOUBLE-SIDED TAPE
QUANTITIES
PARTS
1
1 SET
1
4
2
2
ATTACHED TAPPING SCREWS (M5 X 16)
2018/01