BleBox mremote User Manual

control in the WiFi technology
CONTROL DEVICES WITH A REMOTE CONTROL
The product contains batteries described in Directive
2013/56 / WE, which can not be disposed of with other
household waste.
Avoid mechanical damage. Batteries can explode or cause burns if they
are damaged (e.g. crushed), or exposed to re or high temperature.
Do not remove the device housing. Removal of the housing will cause
permanent damage to the product and will void the warranty.
1
2
3
4
1
The remote control has a multi-colored LED diode and a vibration function. It
is powered from a built-in lithium battery, charged via a micro-usb connector,
with a standard 5V charger or USB connector.
Feature for the remote control is available in devices of the wBox series, with
software version above 0.500
The remote control communicates directly with wBox controllers - no router is
required. Communications of the remote control is two-way, the user receives
feedback information about the execution of the command by the controller
by using a vibration and the signal of the LED. The red LED indicates that an
error has occurred.
2
There are currently four groups (channels) to which drivers can be assigned.
The selection of the group is made by shortly pressing the "menu" button,
which will changes the colors of the LED signaling, indicating the selection of
the group.
miniature universal remote control
1
2
3
4
GENERAL INFORMATION
GROUP SELECTION
User manual
3
Pairing is a procedure aimed at creating a safe connection between the
remote control and the wBox controller.
You need to prepare the controller which is to be paired to the remote control,
by connecting to the phone with the application wBox and going to the
settings menu and next:
1. select a determinated group by scrolling them with a short pressing
of the button (4)
2. press and hold for approx. 2 sec. button (4) - the LED will start
Flashing
3. press (but not simultaneously - with a minimal delay) and hold
(together) for about 2 seconds the central buttons of the remote
control : (2) and (3) - the LED will blink faster
4. press (but not simultaneously - with a minimal delay) and keep
pressed (together) for about 2 seconds thebuttons ofremote control:
(4) and (1) - the LED will blink even faster
5. brie y press the remote control button (1) to enter to the pairing
mode - the LED will be permanently illuminated
6. Within a maximum of 20 seconds, in the controller settings menu,
pleasepress the "Add remote control" button. The correct pairing will
becon rmed by the correct message and a vibration of the control
remote.
An error in the previous procedure will be signaled by a blinking LED in red
color. In thes case youneed to repeat the procedure from the beginning.
4
The unpairing is a procedure aimed at removing the connection between
the remote control and the wBox controller.
The remote control can be unpaired from the controller using two methods,
depending on the situation:
Method 1 – remove the remote control from the list of "remote controls" in
the controller.
This is a standard method in case we have access to the controller but we do
not want to control it anymore with the remote control. In the controller
settings, in the "remote controls" section, delete the determined remote
control from the list. The controller from now on will not respond to the
commands of the remote control, while the remote control at the rst attempt
to control, will automatically remove the association with the device, and will
signal the error with a blink of a red LED and vibration.
Method 2 – remove the controller association in the remote.
This method is recommended when we do not have access to the controller,
and we want to clear the memory of the whole group. Follow the pairing
procedure in accordance with points 1-4. However, in point 5, instead of
pressing the button (1), it is necessary to press the button (2) for a long time
(about 2 seconds). The control remote immediately unpairfrom all the
controllers in this group and will not be able to control them anymore. It
should be noted that in the controller settings, in the "remote controls"
section, the given pilot will still be visible in the device list.
PAIRING
UNPAIRING