Eneo IAM-6MC1001MTA Quick Installation Manual

Quick Installation Guide
Ethernet Coax Transmitter/Receiver,
Data & Power over Coax,
1 x RJ-45, 1 x BNC
IAM-6MC1001MTA
IAM-6MC1001MRA
Please read carefully the instruction manual before use. Depending
on the model, the image and the actual look of the product may vary.
Package
EPoC Extender
(Transmitter / Receiver)
Hardware Overview
Right
NO ANALOG
CAMERA
Bracket
Bracket Hole 브라켓 홀
PoE ON/OFF Switch
PoE ON/OFF 스위치
(Transmitter model only) (ECP-2601T 전용)
Left
ETHERNET
PoE
ON OFF
Bracket
브라켓 홀
Bracket Hole
RJ45
LED Indicators
Indicator Color
PoE-ON PoE Output Status
PD-AUX PoE Input Status
Data-Link Blinks when transmitting Ethernet data
Join-Link EPoC products connected
Power 56VDC or PoE Input connected
Quick
Installation
Guide
Bracket Quick Installation
Guide
& Screw
56V DC
DC Power Jack DC 전원 어댑터
PoE-ON (Transmitter model only)
PoE-ON (ECP-2601T)
PD-AUX (Receiver model only)
PD-AUX (ECP-2601R)
PoE-ON
Data-Link
Join-Link
Power
Join
Join 버튼
Join Button
Status LED Indicator 상태 표시등
Function
(Transmitter model only)
(Receiver model only)
Overview
EPoC Extender is a High-Speed, long distance Ethernet & PoE extender that
makes possible to transmit the Ethernet signal up to 2.4Km and PoE up to
1.2Km via Coax (or UTP, 2wire & Etc.) cables in different situations.
It is cost-effective and time saving solution to migrate existing analog system
to IP based system since EPoC Extender supports easy installation utilizing
the existing cable.
With long distance transmission feature, the device makes to overcome 100
meters distance limitation easily and reduces the construction cost
significantly compared with fiber optic configuration.
Features
 Ethernet over Coax communication following IEEE1901 Standard
 Data + Power over Coax cable (or UTP, 2-Wire)
 Data distance up to 2.4Km
 PoE distance up to 1.2Km
 Max. 95Mbps Bandwidth
 10/100 Full Duplex
 128bit AES network encryption
 Supports Multi-connection (Daisy chain, Star, etc.)
 PoE, PoE+, Extra PoE (Max. 60W output) - Transmitter model only
 Supports UTP, Telephone (2 Pairs), 2-Wire cable communication
(Using BTE Series)
 LED Indication (PoE, Data, Join, Power)
 Plug & Play
 Surge Protection
 Support PoE+ Input (25.5W) from PSE devices (PoE Switch or Injector)
– Receiver model only
 Slim design
Installation Guide
1. Set the IP address on the camera following the instruction manual
of the camera.
If the camera IP is automatically assigned (DHCP, etc.), there is no
Î
need to set the camera IP separately.
2. Connect BNC of the coaxial cable to each Transmitter/Receiver.
3. Connect 56V DC power to Transmitter/Receiver first and then to
AC outlet.
Receiver can be powered by PoE Switch Device (PoE+ PD
Î
Supported) but for safe working, it recommeded to use 56VDC
Power supply on Receiver. When using both PoE switch Device and
power supply at the same time, power supply works preferentially.
In case of 7W camera, the device supports long distance PoE
Î
transmission up to 1,200m over RG6 coaxial cable.
PoE transmission distance can be varied depending on cable type
and Camera's power consumption(W).
Please download full manual for more information about PoE
Î
distance by various cables.
4. When they are connected without any problem, Power / Join Link
LED are on.
5. Adhere the brackets in the package to Transmitter/Receiver and
then fix up the products.
6. Connect the UTP(LAN) cable between Receiver and NVR first and
then between Transmitter and camera.
7. Turn on the PoE switch on Transmitter for PoE IP camera and if the
camera is powered by a separate power source (not powered by
PoE output feature of the Transmitter), turn off the PoE switch on
Transmitter.
Both Transmitter/Receiver send data and power together via BNC
Î
connector. Receiver does not have PoE support so that it can send
data only via RJ45.
8. Ping test is recommended to confirm the whole network after
installation.
9. Check the video signal on the monitor.