Advertisement
Quick Links
2019-01-22 12:43
Wireless AC Sensor manual
Introduction
The Wireless AC sensors are used to measure and calculate PV Inverter current (A), voltage (V), power
(W) and energy (kWh), and show it on a
one gateway per system and one sensor per phase. The gateway connects to the Color Control via
Ethernet, and is the DECT hub for the sensors. Multiple sensors connect to 1 gateway.
Note that it is not possible to use multiple sensors on the same position (AC-Out, AC-In 1, etcetera) in
a system. The CCGX will in such case only show the value of the last-read sensor.
Three phase
For measuring a three phase system, we recommend to use
phase meters does not provide true three-phase metering and measurements.
Required hardware
TIM000100100 - Wireless AC sensor 25A (one for each phase)
TIM000100000 - Wireless Sensor gateway (one for every system)
Included with the gateway:
RJ45 cable 30cm
AC adapter
Note that instead of powering the Wireless Sensor gateway with the AC
adapter, it is also possible to power it from one of the USB ports in the
Color Control GX. Purchase a separate male Micro-USB to male USB
cable, not available from Victron Energy. Note that, due to CCGX-USB
port power limitations, this cannot be combined with a USB-GPS, USB-
WiFi using a non powered USB hub.
Installation
Installing the gateway
1.
Disconnect the AC power
2.
Connect the gateway to the Ethernet/LAN network using the supplied RJ45 cable.
3.
Connect the AC power adapter or the USB cable from the ColorControl GX to the gateway
Victron Energy - https://www.victronenergy.com/live/
1/5
Color Control GX
and the
this
Wireless AC Sensor manual
VRM
Portal. An installation will have
meter instead. Using three single
Advertisement
Related Manuals for Victron energy ET112
Summary of Contents for Victron energy ET112
- Page 1 USB ports in the Color Control GX. Purchase a separate male Micro-USB to male USB cable, not available from Victron Energy. Note that, due to CCGX-USB port power limitations, this cannot be combined with a USB-GPS, USB- WiFi using a non powered USB hub.
- Page 2 Last update: 2019-01-22 10:16 ccgx:ccgx_wireless_ac_sensor https://www.victronenergy.com/live/ccgx:ccgx_wireless_ac_sensor Installing the sensor(s) For each phase, connect the AC sensor according to the schematic below. Neutral on top side. Line on bottom side. Make sure the direction of the current is correct. Gateway and sensor pairing After powering the sensor for the first time, it needs to be paired with the gateway.
- Page 3 When connected for the first time only the ID number will be shown and no location. This needs to be selected for the sensor to work properly. Select a sensor to assign a location to it. For example AC-In1_L3. Victron Energy - https://www.victronenergy.com/live/...
- Page 4 Last update: 2019-01-22 10:16 ccgx:ccgx_wireless_ac_sensor https://www.victronenergy.com/live/ccgx:ccgx_wireless_ac_sensor Sensor readout When all the sensor are configured the measured values can be seen. Go to the Device List and select PV Inverter on AC In1 for example. Specifications Rated voltage V AC Operating Voltage 220-240 V AC Frequency...
- Page 5 2019-01-22 12:43 Wireless AC Sensor manual DISQUS View the discussion thread. From: https://www.victronenergy.com/live/ - Victron Energy Permanent link: https://www.victronenergy.com/live/ccgx:ccgx_wireless_ac_sensor Last update: 2019-01-22 10:16 Victron Energy - https://www.victronenergy.com/live/...