Advertisement
Quick Links
Advertisement
Related Manuals for Circuit-test PSB-4332
Summary of Contents for Circuit-test PSB-4332
- Page 1 CIRCUIT-TEST Power Supply Control Software PSB-4332 PSB-4618 USER MANUAL...
- Page 2 PSB-4332_4618 08R18...
- Page 3 1. Introduction The PC software feature allows remote access of the Circuit-Test power supplies with USB or Ethernet connectivity. Following Circuit-test power supply models are compatible with this PC software. Supported Power Supply Models PSB-4332 PSB-4618 Supported OS System Windows 7 (32-bit and 64-bit), Windows 10 (32-bit and 64-bit) USB driver installation Unzip the downloaded file and run “VCP_V1.4.0_Setup.exe”...
- Page 4 PC Software Installation Please download the PC control software for the respective power supply model from the website www.circuittest.com a) Run file “PC Control software.exe” and click to continue. b) Select the destination location for software installation and click to continue.
- Page 5 c) Select Start Menu Folder and click to continue. d) Click the check box if you would like to create a desktop icon. Then click to continue. e) Click to start installing the software.
- Page 6 2. PC Software Usage 2.1 Main Display The Main interface is divided into 6 panels. 1. Display panel – use to display real-time information of power supply. 2. Main configuration and data log display panel – use to change general setting of program and display data log.
- Page 7 2.2 Connect to Power Supply Before edit any connection setting, the software will not connect to power sup- ply. It just show following display. The first thing you need to do is to edit correct connection for your system. If there are saved connection setting in software. The software will search power supply and connect automatically.
- Page 8 ii. Click on to start edit connection. The connection edit panel come up. iii. Enter connection name for this connection setting and description. e.g. PS-1 iv. Select connection type for your system. It allow configure for USB, Ethernet and RS485.
- Page 9 v. Enter addition connection parameters. For Ethernet, enter IP address and remote port number. (It can be check in menu Display Information LAN Information. → → Please refer to hardware manual). For USB, enter COM port. The COM port can be find in device manager of Windows system after driver installed.
- Page 10 2.3 Display Panel The display shows following information Output Voltage value Output Current value Output Power value Output On/Off status C.V./ C.C. Model Setting values...
- Page 11 2.4 Set output voltage value, current value and ON/OFF status It allow direct input voltage value and current value in setting area or use slide bar to adjust value. After adjust the value, then click button to confirm setting. 2.5 Internal Preset Memory If the power supply models has internal preset memory, this tab will be shown.
- Page 12 2.6 External Timed Program Select External Timed Program tab to operate with 20 user define steps program. It can define Voltage, Current, running time and Output ON/OFF for each step. User can setting running cycle for the Timed Program. External Timed Program is completely controlled by PC, PC counts the time and changes voltage and current of power supply.
- Page 13 Select running cycle between 0-999. You can use slide bar to select or directly input value in text box. Input 0 means run the program forever. Click button to start running cycle. In between program running cycle, click button to stop program. Click to clear the setting.
- Page 14 2.8 Calibration If the power supply support calibration, you will find the Calibration tab is shown. Enter password. The default password is “password” Click “Start calibration” to start calibrate power supply. The system will show setting value for voltage and you input actual output value which measured by multi-meter.
- Page 15 Notes:...
-
Page 16: Circuit-Test
CIRCUIT-TEST E L E C T R O N I C S Division of R.P. Electronic Components Ltd. BURNABY, BC CANADA V5J 5M8...