NEC Express5800/R110f-1E Getting Started

Getting Started!
Be sure to read this guide carefully before using this
server and retain it for reference.
This document provides information required to use your server safely and properly.
Keep this document nearby so that you may refer to it as necessary. Before using this server, be sure to
read this guide and " User's Guide " (in the DVD provided with this server). For details of names in this
document, refer to Names and Functions of Parts in the " User's Guide ".
Safety precautions
Follow the instructions in this guide for the safe use of the NEC Express server.
This guide describes dangerous parts of the server, possible hazards, and how to avoid them.
Server components with possible danger are indicated with a warning label placed on or
around them.
In this guide or on warning labels, WARNING or CAUTION is used to indicate a degree of
danger. These terms are defined as follows:
Indicates there is a risk of death or serious personal injury
Indicates there is a risk of burns, other personal injury, or
property damage
Precautions and notices against hazards are presented with one of the following three
symbols. The individual symbols are defined as follows:
Attention This symbol indicates the presence of a hazard if the
instruction is ignored.
An image in the symbol illustrates the hazard type.
Prohibited This symbol indicates prohibited actions. An image
Action in the symbol illustrates a particular prohibited
action.
Mandatory This symbol indicates mandatory actions. An image
Action in the symbol illustrates a mandatory action to avoid
a particular hazard.
(A label example used in this document)
Symbols to draw attention Description of a warning Term indicating a degree of danger
Use only the specified outlet
Use a grounded outlet with the specified voltage. Use of an improper power
source may cause a fire or a power leak.
Symbols used in this document and on warning labels
Attentions
Indicates the presence of electric shock Indicates the presence of mechanical
hazards. parts that can result in bodily injury.
Indicates the presence of a hot surface Indicates the presence of mechanical
or component. Touching this surface parts that can result in pinching or
could result in bodily injury. other bodily injury.
Safety precautions (continued)
Do not pull out a cable by gripping the cable part.
Pull a cable straight out by gripping the connector part. Pulling a cable by
gripping the cable part or applying extra pressure to the connector part may
damage the cable part, which may cause a fire or electric shock.
Insert the power plug into the outlet as far as it goes.
Heat generation resulting from a halfway inserted power plug (imperfect contact)
may cause a fire. Heat will also be generated if condensation is formed on dusty
blades of the halfway inserted plug, increasing the possibility of fire.
Do not use any unauthorized interface cable.
Use only the interface cables provided with the server. Electric current that
exceeds the amount allowed could cause fire. Also, observe the following
precautions to prevent electrical shock or fire caused by a damaged power cord.
• Do not stretch the cord harness • Do not bend the power cord.
• Do not twist the power cord • Do not step on the power cord.
• Uncoil the power cord before use
• Do not secure the power cord with staples or equivalents
• Do not use a damaged power cord (replace the damaged power cord with a
power cord of the same standard. For information on replacing the power cord,
contact the store where you purchased the product or a sales representative.
• Do not pinch the power cord • Keep chemicals away from the power cord
• Do not place any object on the power cord
• Do not alter, modify, or repair the power cord
Do not use the attached power cord for any other devices or usage.
The power cord that comes with your server is designed aiming to connect with
this server and to use with the server, and its safety has been tested. Do not use
the attached power cord for any other purpose. Doing so may cause a fire or an
electric shock.
Installation, relocation, storage, and connection
Do not attempt to lift the server by holding the front bezel.
Securely hold the server by the base to move or lift. Do not attempt to lift it by
holding the front bezel. Doing so may cause the front bezel to come off, which
may cause not only breakage of the server but also cause the server to fall on to
persons resulting in personal injury.
Do not install the server in any place other than specified.
Do not install the server in the following places or any place other than specified
in this User's Guide. Failure to follow this instruction may cause a fire.
• A dusty place • A humid place such as near a boiler
• A place exposed to direct sunlight • An unstable place
Do not use the server in an environment where corrosive gas is present
Do not install the server in a place subject to corrosive gases including sodium
chloride, sulfur dioxide, hydrogen sulfide, nitrogen dioxide, chlorine, ammonia,
or ozone. Do not install the server in an environment that contains dust,
chemicals that accelerate corrosion such as NaCl or sulfur, or conductive
materials. Failure to follow this warning may cause the wiring on the printed
wiring board to short-circuit, leading to fire. If you have any questions, contact
the store where you purchased the product or a sales representative.
Do not install the server while the cover is removed
Do not install the server to a rack while the cover or other relevant items removed. Not
only will the cooling effect within the server decrease, causing the server to malfunction,
but also may allow dust to enter the server, resulting in fire or electrical shock.
Do not get your fingers caught in the rails
When mounting/removing the server onto/from the rack, be careful to avoid
getting your fingers caught in the rails or cutting your fingers on the rails.
Do not apply any weight on the server when it is extended from the rack
Do not apply force on the server when it is extended from the rack. Doing so
cause the frames to bend, which makes it impossible to be mounted on the rack.
It also may cause the server to fall, resulting in personal injury.
Do not attempt to connect or disconnect the interface cable while the power
cord is plugged into an outlet
Be sure to unplug the power cord from a power outlet before connecting/
disconnecting any interface cable to/from the server. If the server is off-powered
but its power cord is plugged to a power source, touching a cable or connector may
cause an electric shock or a fire resulted from a short circuit.
R110f-1E R110f-1E
Indicates there is a risk of explosion.
Indicates there is a risk of fire or fumes.
Indicates there is a risk of electric shock
for the multiple receiving.
First Edition, July
2013
Prohibited actions
Do not disassemble, repair, or modify
the server. Otherwise, an electric shock
or fire may be caused.
Do not touch the component specified
by this symbol. Otherwise, an electric
shock or burn may be caused.
Do not place the server near the fire.
Otherwise, a fire may be caused.
Mandatory actions
Unplug the power cord of the server.
Otherwise, an electric shock or fire may
be caused.
Make sure equipment is properly
grounded. Otherwise, an electric shock
or fire may be caused.
Safety notes
General
Do not use the server for services where human life may be at stake or high
reliability is required.
This server is not intended for use in medical, nuclear, aerospace, mass transit or
(Example)
other applications where human life may be at stake or high reliability is required, nor
(Electric
is it intended for use in controlling such applications. We disclaim liability for any
shock risk)
personal injury and property damages caused by such use of this server.
(Example)
Do not use the server if any smoke, odor, or noise is present.
(Do not
If smoke, odor, or noise is present, immediately turn off the server and
disassemble)
disconnect the power plug from the outlet, then contact the store where you
purchased the product or your maintenance service company. Using the server
(Example)
(Disconnect a in such conditions may cause a fire.
plug)
Do not insert needles or metal objects.
Do not insert needles or metal objects into ventilation holes in the server or
openings in the optical disk drive. Doing so may cause an electric shock.
Use a rack that conforms to the designated standard
This server can be mounted onto a 19-inch rack that conforms to EIA standards.
Do not mount the server onto any rack that does not conform to EIA standards.
Doing so may cause a server malfunction, personal injury, or damage to
peripheral devices. For more information about racks that can be used with the
server, consult with your sales representative.
Use the server only under the specified environment
Do not install the server rack in any environment that is not suitable for installation.
Installation in an unsuitable environment is harmful for the server and other
systems installed in the rack and may cause fire or personal injury due to the
rack falling. For a detailed explanation on installation environments or seismic
reinforcement, see the instruction manual supplied with the rack or consult with
your sales representative.
Keep water or foreign matter away from the server.
Do not let any liquid such as water or foreign materials including pins or paper clips enter
the server. Failure to follow this warning may cause an electric shock, a fire, or failure of the
server. When such things accidentally enter the server, immediately turn off the power and
disconnect the power plug from the outlet. Do not disassemble the server, and contact the
store where you purchased the product or your sales representative.
Use only the specified interface cable.
Use only interface cables provided by NEC and locate a proper device and
connector before connecting a cable. Using an authorized cable or connecting a
cable to an improper destination may cause a short circuit, resulting in a fire.
Also, observe the following notes on using and connecting an interface cable.
• Do not use any damaged cable connector. • Do not step on the cable.
• Do not use the server with loose cable connections.
• Do not use any damaged cable.
Cleaning and working with internal devices
Do not disassemble, repair, or alter the server.
Never attempt to disassemble, repair, or alter the server on any occasion except
as described in this document. Failure to follow this warning may cause not only
malfunction of the server but also an electric shock or fire.
Do not look into the optical disk drive
A laser beam used in the optical disk is harmful to the eyes. Do not look into or
insert a mirror into the drive while the drive is powered on. If a laser beam (which
is invisible) enters your eyes, you may lose your eyesight.
Do not attempt to remove lithium, NiMH, or Li-ion batteries by yourself.
The server contains the lithium, NiMH, or Li-ion battery (some optional devices
have a lithium, NiMH, or Li-ion battery installed). Do not remove the battery by
yourself. Placing a battery close to a fire or in the water may cause an explosion.
When the server does not operate appropriately due to the dead battery, contact
the store you purchased the product or your sales representative. Do not attempt
to disassemble the server to replace or recharge the battery by yourself.
Danger of explosion if battery is incorrectly replaced. Replace only with same or
equivalent type recommended by the NEC. Do not dispose of batteries in a fire or
with household waste. Contact your local waste disposal agency for the address
of the nearest battery deposit site.
Disconnect the power plug before cleaning the server.
Be to power off the server and disconnect the power plug from a power outlet
before cleaning or installing/removing internal optional devices. Touching any
internal device of the server with its power cord connected to a power source
may cause an electric shock even of the server is off-powered.
Occasionally disconnect the power plug from the outlet and clean the plug with a
dry cloth. Heat will be generated if condensation is formed on a dusty plug, which
may cause a fire.
High temperature
Components including internal hard disk drives in the server are extremely hot just
after the server is turned off. Allow the surface to cool before installing/removing.
Secure cables or cards in place
Be sure to secure the power cord, interface cables, and cards in place.
Incomplete installation causes a loose connection, resulting in smoke or fire.
Electric shock
The hard disk drives support hot swapping. If replacing a component when the
electrical current is being supplied, use extreme caution not to get electric shock
by touching terminal parts of the internal components.
During operation
Do not pull out or remove the server from the rack.
Do not pull the server out of the rack or remove it from the rack. In addition to causing
equipment to not function properly, separating the server from the rack may result in
personal injury.
Avoid contact with the server during thunderstorms.
Do not touch any part of the server including the cables when a thunderstorm is
approaching. Also, do not connect or disconnect any devices. There may be a
risk of electric shock from lightning strike.
Keep animals away from the server.
Keep animals such as pets away from the server. Pet hair or other waste enters
the server, which may cause a fire or electric shock.
Rack installation
Indicates the presence of laser beam
that cause blindness.
Indicates a general notice or warning
that cannot be specifically identified.
Do not touch the server with wet hand.
Otherwise, an electric shock may be
caused.
Do not use the server in the place where
water or liquid may pour. Otherwise, an
electric shock or fire may be caused.
Indicates a general prohibited action
that cannot be specifically identified.
Indicates a mandatory action that
cannot be specifically identified. Make
sure to follow the instruction.
Power supply and power cord use
• Do not place any object on the cable.
Warning labels
Warning labels are attached on or near the components
with potential dangers. Be sure to read and keep them.
(Do not remove or black out this label). If no label is
attached or printed on the server, or if there is a label
coming off or stained, contact your sales representative.
Transfer, movement, and disposal
Observe the following precautions when you transfer (or sell) the server or software provided
with the server to a third party.
ⓦ Server
When transferring (or selling) the server to a third party, be sure to provide this manual
(including electronic data) to the third party.
Be sure to completely delete all important data from Hard Disk Drive. (Even if you
cannot see the data on OS, the data might remain in the HDD.) NEC is not
responsible for any data leakages when transferring or selling the server to a
third party.
ⓦ Provided software
Observe the following precautions when transferring (selling) the provided software to a
third party.
- All provided software applications must be transferred and no backup copies must be retained.
- Transfer requirements listed in the " Software License Agreement " that comes with each
software application must be satisfied.
- Software applications that are not approved for transfer must be uninstalled before
transferring the server.
ⓦ Disposal of server and consumables
Dispose of the server, accessories (such as power cord), HDD, DVD, option board, and
battery according to laws and regulations of the central and/or local government. For
details about how to discard (and replace) the battery installed in this product, contact your
sales representative.
Regarding the transportation of this server
This server and/or some of the associated optional devices uses lithium metal batteries or
lithium ion batteries. Regulations for air/ocean transportation apply when transporting lithium
batteries. Conform to the regulations if you want to transport this server or optional devices by
air or ship.
Do not attempt to carry or install the server alone
More than two people are required to carry or install the rack. Otherwise, the rack
may fall, resulting in personal injury or damage to peripheral devices. In particular,
tall racks such as a 44U rack become unstable unless steadied with a stabilizer.
Make sure that two or more people hold the rack to carry or install the rack.
Do not install with the load weight distributed unevenly
To avoid unevenly distributing the load of the rack and server, install a stabilizer
or connect multiple racks to distribute the weight. Otherwise, the rack may fall,
resulting in personal injury.
Do not install components alone, and check the door hinge pins of the rack
Two or more people are required to install the rack components such as the door
or rails. When installing the door, make sure that both upper and lower hinge pins
are held in place. Incomplete attachment may cause components to fall off as
well as personal injury.
Do not extend any device from the rack that is not stabilized
When extending a device from the rack, make sure that the rack is stable (by
using a stabilizer or seismic reinforcement). Otherwise, the rack may fall,
resulting in personal injury.
Do not extend more than one device out of the rack
Extending multiple devices from the rack may cause the rack to fall, resulting in
personal injury. Extend only one device at one time.
Do not exceed the rated capacity of the power supply when connecting devices
To prevent burn injuries, fire, and damage to the server, make sure the load on
the branch circuit that supplies power to the rack will not exceed the rated load.
For inquiries regarding the installation or wiring of the power supply system,
consult with the company that performed the installation or wiring, or the power
company that services your area.
Do not hold the power plug with a wet hand.
Do not disconnect/connect the plug while your hands are wet. Failure to follow
this warning may cause an electric shock.
Do not connect the ground wire to a gas pipe.
Never connect the ground wire to a gas pipe. Failure to follow this warning may
cause a gas explosion.
Power supply cord
This server may be shipped with multiple power supply which requires more than
one connector to AC mains.
The AC power cord(s) is consider as the mains disconnected device for the server,
always disconnect the power supply cord(s) before opening up or servicing the server.
Power supply
The power supplies in your system may produce high voltages and energy
hazards, which can cause bodily harm. Unless you are instructed otherwise, only
trained service technicians are authorized to remove the covers and access of
the components inside the system.
Plug in to a proper power source.
Use a grounded outlet and observe the specified voltage. Use of an improper
power source may cause a fire or a power leak.
Do not install the server where you need an extension cord. Use of a cord that does not
meet the power specifications of the server may heat up the cord and cause a fire.
If you want to use an AC cord set with a ground wire of class OI, be sure to connect
the ground wire before inserting the power plug into the outlet. Before disconnecting
the ground wire, be sure to disconnect the power plug from the output.
Do not connect many cords into a single outlet by using extension cords.
The electric current exceeding the rated flow overheats the outlet, which may
cause a fire.
Do not leave the optical disk drive tray open.
Dust may get in the server when the tray is open, which may result in a
malfunction. In addition, bumping the open tray could cause personal injury.
Do not remove the server from the rack while it is operating.
Do not pull out or remove the server from the rack while the server is running. In
addition to causing equipment to not function properly, separating the server
from the rack may result in personal injury.
Do not place any object on top of servers.
Separating the server from the rack may result in personal injury and damage to
nearby personal belongings.
Do not get yourself caught in the fan
Keep your hands and hair away from the cooling fan at the rear of the server
during operation. Failure to observe this warning may cause your hands or hair
to catch in the fan, resulting in personal injury.
3.5-inch drive model
Label location