1. Manuals
  2. Brands
  3. setro Manuals
  4. Locks
  5. miniK10m
  6. Operating manual

setro miniK10m Operating Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Operating
manual
CABINETS | LOCKERS | BOXES
The easy lock
in every aspect

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the miniK10m and is the answer not in the manual?

Questions and answers

Related Manuals for setro miniK10m

Summary of Contents for setro miniK10m

  • Page 1 Operating manual CABINETS | LOCKERS | BOXES The easy lock in every aspect...
  • Page 2 Index Operating manual Introduction Description Usage Initial setup Assign Master card Selecting Operation option of the miniK10 Assign/Delete Service card / cards Assign User card / cards Deleting User card Operating instructions Personal operation with card (if selected) To Unlock To Lock Locker mode operation with card (if selected) To Lock...
  • Page 3 Index Programming instructions Restore Default Settings: Press 0 - 1 Default Settings are Mute Operation: Press 2 - 0 Audible Operation: Press 2 - 1 Penalty Operation: Press 3 - 1 Delete All Uvser Cards: Press 4 - 0 Reset User Password: Press 4 - 1 Locking with password / card: (1) Press 6 - 0 Automatic Locking (without password/card): Press 6 - 1...
  • Page 4 Back Description: Besides the stylish and enriching design of the miniK10m / miniK10p cabinet lock, there are various features that make the lock different from others, such as allowing to use with wet hands, easy and quick installation at wood and steel cabinets, easy application at existing cabinets, easy application at right/left cabinet doors, higher battery life with very low energy consumption, high reliability and operating with a contactless card.

  • Page 5: Initial Setup

    Usage: Contactless card lock can be used with three types of cards: “User Card, Service Card and Master Card”. Also, the lock can be used with a password by selecting the user card free operation. Service card is passive by default. You should center the card when holding over the keypad to enable accurate reading.
  • Page 6 Assign/Delete Service card / cards: (If you don’t need to use any service card, skip this step) 1- Press , present the master card to the keypad and press green and red leds blink. 2- Press 5 for selecting service card assign / delete option. And then Press 0 for all service cards are deleted.
  • Page 7 Operating instructions: Personal operation with card (if selected) To Unlock: 1- Press any number button for wake the lock up. 2- Present any assigned user card / master card / service card to the keypad in 3 seconds. 3- turn the handle to the unlocked position. To Lock: 1- Press any number button for wake the lock up.
  • Page 8 To Unlock: 1- Press any number button for wake the lock up. 2- Present any card / master card / service card to the keypad in 3 sec. 3- Turn the handle to the unlocked position. Cardless personal operation (if selected) Change Password: (default “1010”) 1- Press...
  • Page 9 To Lock with Password: (default “1010”) 1- Enter the user password. 2- Turn the handle to the locked position. USER PASSWORD To Lock with Card: 1- Press button for wake the lock up. 2- Present master card to the keypad in 3 seconds 3- Turn the handle to the locked position.
  • Page 10 To Unlock with Password: 1- Enter the same password with locking operation. 2- Turn the handle to the unlocked position. LOCKER MODE PASSWORD To Unlock with Cards: 1- Press button for wake the lock up. 2- Present master card / service card to the keypad in 3 seconds 3- Turn the handle to the unlocked position.
  • Page 11 Locker Mode Operation with Card or Password to Lock/Unlock (if selected) To Lock with Password: (default “1010”) 1- Enter the new password. 2- Turn the keypad to the locked posit LOCKER MODE PASSWORD To Unlock with Password: 1- Enter the same password with locking operation. 2- Turn the handle to the unlocked position.
  • Page 12 To Lock with any card: 1- Press button for wake the lock up. 2- Present any card to the keypad in 3 seconds. 3- Turn the handle to the locked position. To Unlock with any card: 1- Press button for wake the lock up. 2- Present any card to the keypad in 3 seconds.

  • Page 13: Programming Instructions

    Programming instructions: 1- Press , present the master card and then press green and red leds blink. 2- Enter the program number to be customized and then enter the selected settings number. (Press Program Number and then Selection Number) Restore Default Settings: Press 0 - 1 Default Settings are: Locker mode operation with card, audible operation, penalty operation is not active, service card is not active, locking with password, door open warning is...
  • Page 14 Locking with password / card: Press 6 - 0 Locking operation require a password / card to lock. Automatic Locking (without password/card): Press 6 - 1 Locking operation does not require a password / card to lock. Warning of open door : Press 7 - 1 After door is open for one minute, lock gives an audible warning to user with 8 beeps every seconds to notify user that the door has been left open.
  • Page 15 Factory Settings: Prog. No 1-1: Locker mode operation with card Prog. No 2-1: Audible beeps and confirmations Prog. No 3-0: Penalty operation PASSIVE Prog. No 4-0: Delete all user card Prog. No 5-0: Service card PASSIVE Prog. No 6-1: Locking with password Prog.

  • Page 16: Maintenance

    Maintenance: Clean front of lock with a mild damp cloth with detergent if needed. Use only Ethanol (Ethyl Alcohol) for disinfecting. Do not use any hard or scratching cleanser. Do not clean with chemical materials that melt plastic (thinner, acetone, etc.) Be careful not to spill water on lock.

  • Page 17: Limited Warranty

    Limited warranty: Vemus Ltd. offers a one year limited warranty all products to be free from man- ufacturing defects in materials and workmanship. This warranty does not cover the battery, lost combinations or damages caused by improper mounting, improper or unreasonable use. Liability limits: This is a limited warranty and is in lieu of all other warranties (including the implied warranties of merchantability and fitness for use) and under no...
  • Page 18 K10p card specifications: Transponder Chip EM4100 Compatible Frequency 125Khz ID Size 64 bit Read Only Encoding Manchester Encoding K10m Appropriate card: MIFARE Classic®, MIFARE® DESFire® cards... Thank you Congratulations for making this eco-friendly choice! By purchas- ing a miniK10, you will prevent additional batteries going to the landfills over the up to 5 years.
  • Page 19 quick info LOCKING / UNLOCKING WITH USER CARD LOCKING / UNLOCKING WITH MASTER CARD If cardless personal operation option or cardless locker mode operation option is selected, you should press button at first to lock and unlock by using the master card.

  • Page 21: Installation

    Installation CABINETS | LOCKERS | BOXES The easy lock in every aspect...

  • Page 22: Installation Overview

    Installation Overview 1. miniK10 2. M16x1,5mm Cylinder Nut 3. Stop Cam 4. Cam 22mm Axle 5. Cam 38mm Axle 6. M4x10mm Cam Screw 7-9. Mounting Screws Locking Position (Be sure before mounting). Hinge at the right side 90° Cover thickness Screw size Rotate Right 0 - 5 mm covers...
  • Page 23 Mounting on Left & Right Door RIGHT LEFT Hinges on Hinges on outside of outside of door are on door are on the Right the Left Peg on stop cam Peg on stop cam is on the right side for is on the left side for right doors left doors...
  • Page 24 Surface Mounting Semi-Flush Mounting...
  • Page 25 70,4 g Assembly set is not. 18mm 18mm 18mm 18mm 24mm 27mm 12mm 27mm 24mm 27mm 12mm 27mm...

  • Page 26: Mounting Template

    Ø 0,16” (4 mm) Mounting Template Upper Mounting Screw Hole Ø 0,63” (16 mm) Cylinder Hole...
  • Page 27 Joint erect lock assembly measurements 22 mm axle cam 38 mm axle cam...
  • Page 28 Recessed cover assembly measurements...
  • Page 29 Overlapping / external cover assembly measurements right cover on the body 4 mm hole 3 mm 27 mm 62 mm 42 mm 16 mm hole 22 mm cam...

  • Page 30: Locked Position

    NOTE: Read instructions, set combination and test lock BEFORE installing!! Replacing existing lock: 1. Place mounting template centered on existing hole and mark upper mounting screw hole. 2. Drill mounting screw hole. 3. Install lock using adaptor if necessary. 4. Thread nut on cylinder. 5.
  • Page 31 Warnings for mounting: Pull the transparent “Remove to Start” tag coming out of battery cap at the back of the lock and activate the lock. Read the user manual and apply password change and opening/closing operations several times before the mounting of the lock. Before mounting of the lock, switch lock handle to closing position.
  • Page 32 Spa and Baths Schools Staff Lockers Sports Halls In Mailboxes Hospitals setro s.r.o. | Majerská cesta 30/A 974 01 Banská Bystrica | Slovakia +421 48 414 45 19...

This manual is also suitable for:

Minik10p

Table of Contents