Advertisement
RP5-GM11
Optional Steering Wheel Control Programming
If you wish to re-assign the SWC functions the interface must be programmed in the specific order shown on the chart below. If
you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and release
the programming button on the side of the interface to skip that function. The LED will flash off and on confirming that you have
successfully skipped that function and are ready to proceed to the next one.
Programming
1. Turn the key to the ignition position.
2. Press and release programming button on the side of the interface.
3. Within 7 seconds, press the button that is to be learned on the steering wheel. The LED will turn off when the button is pressed.
4. If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.
If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and
5.
release the program button on the side of the interface to skip that function.
6. Once programming is completed, wait seven seconds. The LED will flash three times indicating end of programming.
7. Test the interface for proper functionality. Whenever a SWC is pressed the LED on the interface should blink. If any function
does not work, repeat the programming steps.
Optional Programming Order
1
Volume +
2
Volume -
3
4
Preset +
5
Preset -
6
7
Track +
8
9
10
Enter / Play
11
Band / Program
12
Receive
13
14
15
Testing and Verification
1. Turn the ignition on. The LED on the interface will turn on and the +12v accessory wire will turn on.
2. Turn on the radio and check balance and fade. Note: Premium Factory amplified Systems will not fade as neither the
aftermarket radio or the RP interface have the ability to control the amplifier's fader.
3. Verify that the factory subwoofer (if present) is playing.
4. Verify that all SWC are functioning properly for both the aftermarket radio and OnStar. To adjust OnStar volume, press the
OnStar button on the mirror then use the volume buttons on the SWC to adjust the level. The volume will raise a total of 8
times before returning to the original level.
5. Pressing the OnStar button on the rearview mirror will turn off the rear speakers and allow the OnStar audio to be heard in
the two front speakers. The OnStar active LED will also turn on. When OnStar disconnects, the radio will un-mute or turn
back on and the OnStar LED will turn off. Pressing the Mute/OnStar button on the steering wheel for 1.5 seconds will also
activate Onstar.
6. Turn off vehicle and remove key. RAP will be active and keep the radio on for 10 minutes or until the drivers door is opened.
Pacific Accessory Corporation
Alpine
JVC
Kenwood
Volume +
Volume +
Volume -
Volume -
Mute
Mute
Source
Source
Track +
Source
Track -
Track +
Band / Disc +
Track -
Track -
Preset / Disc -
Disc / FM +
Power
Select
Disc / AM -
Attenuation
Answer
Phone Receive
Phone Reject
On Hook
End
Voice
Off Hook
Voice
Power
Preset +
* Dual / Axxera, Jensen, Rockford Fosgate
Radio Replacement & Steering Wheel Control Interface
with OnStar Retention for General Motors Vehicles
Clarion
Other *
Volume +
Volume +
Volume -
Volume -
Mute
Mute
Mute
Source
Preset +
Play
Search +
Preset -
Search -
Source
Band
Track +
Send / End
Track -
Send
Band
End
Answer **
Voice
Voice
End **
PTT **
Mute
** Jensen ONLY
Pioneer
Sony
Volume +
Volume +
Volume -
Volume -
Mute
Mute
Preset +
Preset +
Preset -
Preset -
Source
Source / End Call
Track +
Track +
Track -
Track -
Band
Band
Phone Menu
Power / End Call
Answer Call
Voice / Answer / End Call
Voice (Android Auto & Car
End Call
Play) Answer / End Call***
Voice
*** XAV-AX100 / 200 Only
Fusion
Volume +
Volume -
Mute
Source
Track +
Track -
Audio
Power
Rev: 5
Page 3
Date: 050918
Advertisement
