Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAfETy
WARNING! Ensure that Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
WARNING! disconnect from air supply before changing accessories or servicing.
Maintain the grinder in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
9
Before each use check abrasive disc for condition. If worn or damaged replace immediately.
9
ensure that the speed rating (rpm) of the disc is the same as, or greater than, the speed rating of the grinder.
9
ensure that there are no flammable or combustible materials near the work area.
9
WARNING! Always wear approved eye (or face) and hand protection when operating the grinder.
Use face, dust, or respiratory protection in accordance with CoSHH regulations.
9
depending on the task, grinder noise level may exceed 85dB in which case wear safety ear defenders.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
Maintain correct balance and footing. ensure that the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
Check moving parts alignment on a regular basis.
9
ensure that the workpiece is secure before operating the grinder. never hold a workpiece by hand.
9
Check the workpiece to ensure there are no protruding screws, bolts, nuts etc.
9
Avoid unintentional starting.
9
WARNING! ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
9
secure.
Prolonged exposure to vibration from this grinder poses a health risk. It is the owner's responsibility to correctly assess the potential
9
hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
DO NOT use the grinder for a task it is not designed to perform.
8
DO NOT operate grinder if any parts are damaged or missing as this may cause failure and/or personal injury.
8
WARNING! DO NOT grind any materials containing asbestos.
DO NOT carry the grinder by the hose, or yank the hose from the air supply.
8
DO NOT force, or apply heavy pressure to, the grinder, let the tool do the work.
8
DO NOT place air line attachments close to your face and do not point them at other people or animals.
8
DO NOT operate grinder when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT use the grinder where there are flammable liquids, solids or gases, such as paint solvents and including waste wiping
8
or cleaning rags etc.
DO NOT carry the grinder with your finger on the power lever.
8
DO NOT direct air from the air line at yourself or others.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
WARNING! The grinding process can produce streams of sparks which are a potential source of ignition especially when
grinding metal.
DO NOT use the grinder where there are flammable liquids, solids or gases.
8
DO NOT allow grinder sparks to make contact with the operator's clothing or any other fabric such as cleaning rags.
8
fabrics contaminated with inflammable materials such as petrol, oil, grease, paint and solvents are a particular fire hazard.
To reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments treated with a fire
9
retardant in preference to man-made fibres.
© Jack Sealey limited
AIR ANGLE GRINDER 100mm
Model no:
Wear protective
Wear protective
gloves
clothing
DANGER Of fIRE/ExpLOSION hAzARD
Original Language Version
SA152.V2
Wear ear
Wear a mask
protection
SA152.V2 Issue 4 (HF) 30/07/18