Air King 9102 Operating Instructions And Parts Manual

4DA35A/9102A
ENSAMBLADO
1. Incline el cabezal del ventilador hacia atrás. Coloque la Parrilla
Plástica Posterior en el Motor. (Figura 1)
2. Alinee el corte triangular en "∆" en la Parrilla Plástica Posterior
con el poste triangular en la parte superior de la cubierta frontal del
Motor. Encaje totalmente la Parrilla Plástica Posterior y fíjela
con la Tuerca de Plástico, haciéndola girar en el Sentido de las
Manecillas del Reloj. (Figura 2)
3. Deslice la Hélice sobre el Eje del Motor. (Alinee la Ranura en el
bloque de la hélice con la Clavija del eje del motor.) (Figura 3)
4. Para fijar la Hélice, atornille el Girador en el Eje en el
Sentido Contrario a las Manecillas del Reloj hasta
que se encuentre fija en el cubo de la hélice.
5. Con el cabezal del ventilador en posición recta, alinee el Ornamento
de la Parrilla Anterior para que quede en posición horizontal.Inserte
la parte inferior de la Parrilla Anterior dentro de la Parrilla Plástica
Posterior. La Lengüeta en la parte inferior de la Parrilla Plástica
Posterior debería encajar entre los rayos de la Parrilla Anterior.
Encaje la Parrilla Anterior dentro de la Parrilla Plástica Posterior
comenzando desde arriba y progresando en forma descendiente
por ambos lados.
Hélice
Parrilla
Parrilla
Posterior
Posterior
Motor
Girador
Tuerca de
Plástico
Parrilla
Anterior
Figura 1 Figura 2 Figura 3
24
22
23
21*
5
4
1
21*
2
3
29
7
9
9
28
13
10
11
12
15
17
14
8
6
16
18
19
26
25
Rev. C 6/07
y 4DA36A/9106A
FUNCIONAMIENTO
OSCILACIÓN VARIABLE: Jale la perilla de oscilación ubicada
en la parte posterior del motor hacia arriba. Gire el cabezal del
ventilador hacia la izquierda, derecha o hacia delante. Empuje la
perilla de oscilación hacia abajo y el ventilador oscilará describiendo el
ángulo fijado.
ÁNGULOVERTICAL: Para ajustar el ángulo vertical, incline el cabezal
del ventilador hacia arriba o abajo, según prefiera.
VELOCIDAD: La velocidad está controlada por una perilla rotatoria:
(0) Apagado, (3) Alta, (2) Media, (1) Baja.
CABLE ELÉCTRICO: Enchufe el cable eléctrico en un tomacorriente
de pared (CA 120 Voltios, 60 Hz).
MANTENIMIENTO
ADVERTENCIA:
SIEMPRE DESENCHUFE EL CABLE ANTES
DE MOVER O DAR SERVICIO AL VENTILADOR.
ADVERTENCIA:
¡NO SUMERJA EL VENTILADOR EN AGUA!
LIMPIEZA: Utilice un paño suave humedecido con una solución
jabonosa liviana, tal como un detergente líquido para lavar platos.
Seque TODAS LAS PARTES POR COMPLETO antes de rearmar.
Después de dar mantenimiento o servicio, REARME POR COMPLETO
la unidad en la forma descrita en este manual de instrucciones, antes
de volver a conectarla a la fuente de poder.
PRECAUCIÓN:
No utilice gasolina, bencina, acetona,
Clavija
limpiadores abrasivos, etc. puesto que dañarán el Ventilador.
NUNCA use ALCOHOL O SOLVENTES.
LUBRICACIÓN: Los cojinetes de precisión vienen sellados de por
vida en la fábrica y no precisarán ninguna lubricación adicional.
ALMACENAMIENTO: Guarde el Ventilador con estas instrucciones
en un lugar fresco y seco.
Ranura
LISTA DE REPUESTOS
NO. DE PARTE PARA EL MODELO
REF DESCRIPCIÓN 4DA35A/9102A
1 Motor 02030062GL
2 Cubierta del motor (frontal) 2010710
3 Cubierta del motor (trasera) 2010661
4 Tornillo Phillips reforzado 02090040
20
# 7 x 7/16
5 Botón de oscilación 2010119
6 Interruptor 02055087
7 Enlace de oscilación 2010276
8 Conector de alambre 2090529
9 Tornillo de enlace 02090140
10 Cuello 2010285
11 Perno de sujeción 02090516
12 Resorte de elevación —
13 Placa de trinquete 02010162B
14 Eje de elevación 2090521
15 Tuerca hexagonal de 5/16-24 02090033
27
16 Base 2010540P
17 Perilla del Interruptor 2010131
18 Placa inferior 2010312
19 Cordón eléctrico con clavija
02050009AWFPC 02050009AWFPC
20 Rejilla frontal 02096217
21 Tapa 2010058
22 Aspa 2010008
23 Tuerca de montaje de la rejilla 2010359
24 Rejilla plastica trasera 2011212
25 Pata de caucho 2010415
26 Tornillo 2090038
27 Ornamento de la rejilla 02010381A
28 Casquillo de cuello osc. 2010808
29 Tornillo #7 x .8 PPH 02090060
*NOTA: Se suministra 1 solo Tapa con el Ventilador.
4
OPERATING INSTRUCTIONS & PARTS MANUAL
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DE-
SCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY
WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

DESCRIPTION

The Air King 12" (30.4 cm) and 16" (40.6 cm) Oscillating Fans feature
whisper quiet operation with a 3 paddle blade. Fan is powered by a
pre-lubricated permanent split capacitor motor with a 6 ft. (1.8 m) 18/3
cord set. Fan grills meet OSHA requirements. UL listed.

SPECIFICATIONS

Motor ........................................ 120V, 60Hz (12")(30.4 cm)
Blade Size ................................ 12" (30.4 cm) Model(4DA35A/9102A)
Speeds ..................................... 3 Speeds
Control ...................................... Rotary Knob
Air Flow Distribution.................. 90°
MODEL 4DA35A/9102A
SPEED HIGH MED
CFM 930 780
M /s 0.43 0.37
3
RPM 1450 1300
Amps 0.40 0.30
Watts 39 35
dB (A) 45 41
4DA36A/9106A CANT.

GENERAL SAFETY INFORMATION

02030066GL 1
When using electrical appliances, basic
2010710 1
precautions should always be followed to
2010661 1
reduce the risk of fire, electric shock and injury
02090040 1
to person, including the following:
2010119 1
1. Read all instructions before using Fan.
02055087 1
2. Make certain that the power source conforms to the electrical
2010276 1
requirements of the Fan.
2090529 1
3. Use this Fan only as described in this manual. Any other use
02090140 2
not recommended by the manufacturer may cause fire, electrical
2010285 1
shock, or injury to persons.
02090516 1
4. Unplug power cord before installing, servicing, or moving the Fan.
02090586 1
WARNING:
DO NOT DEPEND UPONTHE ON-OFF SWITCH
02010162B 1
2090521 1
ASTHE SOLE MEANS OF DISCONNECTING POWERWHEN
02090033 1
INSTALLING OR SERVICING THE FAN. ALWAYS UNPLUG
2010541 1
THE POWER CORD.
2010131 1
5. This Fan must NOT be used in potentially dangerous
2010316 1
1 locations such as flammable, explosive, chemical-laden
02096214I 1 or wet atmospheres.
6. DO NOT use Fan in or near a window. Rain may create an
2010059 1
electrical hazard.
2011013 1
7. The power cord is equipped with a three-prong grounded plug
2010359 1
that must be inserted into a matching receptacle. Under no
2011200M 1
circumstances must the grounding prong be cut off the plug.
2010415 2
Where a two-prong wall receptacle is encountered, it must be
2090038 1
02010381A 1 replaced with a properly grounded three-prong receptacle installed
in accordance with the National Electrical Code (NEC) and all
2010808 1
applicable local codes and ordinances. This work must be done
02090060 2
only by a qualified electrician, using copper wire only.
WARNING:
USE OF A THREE-PRONG TO TWO-PRONG
Rev. C 6/07
2084067
OSCILLATING FANS
12" (30.4 cm) MODEL 4DA35A/9102A
16" (40.6 cm) MODEL 4DA36A/9106A
ADAPTER IS NOT RECOMMENDED. IMPROPER CONNEC-
TION MAY CREATE THE RISK OF ELECTROCUTION. USE
OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA.
WARNING:
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND
PERSONAL INJURY, DO NOT REMOVE, REPLACE, REPAIR
OR TAMPER WITH THE ORIGINALLY SUPPLIED PLUG. IF
THE FAN DOES NOT FUNCTION PROPERLY, IT MAY BE
120V, 60Hz (16")(40.6 cm)
DUE TO THE SAFETY DEVICE INCORPORATED IN THIS
PLUG. RETURN TO AN AUTHORIZED SERVICE CENTER
16" (40.6 cm) Model(4DA36A/9106A)
OR CALL 800-233-0268, MONDAY - FRIDAY, BETWEEN 8:00
AM AND 5:00 PM EST. IF THE PLUG WARNING LABEL IS
MISSING OR DAMAGED, CALL THE TOLL FREE NUMBER
FOR A REPLACEMENT LABEL.
4DA36A/9106A
8. Where possible, avoid the use of extension cords. If they must be
LOW HIGH MED LOW
used, minimize the risk of overheating by ensuring that they are
620 1710 1500 1330
UL listed. Never use a single extension cord to operate more than
0.29 0.80 0.71 0.63
one Fan.
1090 1545 1394 1244 9. DO NOT operate any Fan with a damaged cord or plug or after the
0.27 0.71 0.54 0.48
Fan malfunctions, has been dropped or damaged in any manner.
32 77 65 57
Return Fan to authorized service facility for examination, electrical
36 53 49 44 or mechanical adjustment or repair.
10.DO NOT insert or allow fingers or foreign objects to enter any
ventilation or exhaust opening as it may cause an electric shock
or fire, or damage the Fan. DO NOT block or tamper with the Fan
in any manner while it is in operation.
11.Always place the Fan on a stable, flat, level surface when operating,
to avoid the chance of the Fan overturning. Locate the Power
Cord so the Fan or other objects are not resting on it. DO NOT
run Power Cord under carpeting. DO NOT cover Power Cord with
throw rugs, runners, or the like. Arrange Power Cord away from
room traffic and where it will not be tripped over.
12.This Fan is NOT intended for use in wet or damp locations. Never
locate a Fan where it may fall into a bathtub or other water container.
13. DO NOT use Fan outdoors.
14.This Fan is NOT suitable for use in agricultural facilities including
areas where livestock, poultry or other animals are confined.
Please refer to National Electric Code (NEC) Article 547-7 (2002),
or applicable state or local codes or standards relating to electrical
requirements for Agricultural Buildings.THIS FAN DOES NOT MEET
THE REQUIRMENTS OF NEC ARTICLE 547-7 (2002).
15.This Fan is NOT suitable for use in hazardous locations. Please
refer to National Electric Code (NEC) Article 500 or applicable
state or local codes or standards relating to electrical requirements
for Hazardous locations. THIS FAN DOES NOT MEET THE
REQUIRMENTS OF NEC ARTICLES 500 (2002)
WARNING:
SHOCK – DO NOT USE THIS FAN WITH ANY SOLID STATE
SPEED CONTROL DEVICES.
SAVE THESE INSTRUCTIONS
1
THIS PLUG IS A SAFETY FEATURE. TO
REDUCE THE RISK OF FIRE OR ELECTRIC
2084067