Page 1: Table Of Contents
Contents Important Statement ······················· afety recautions ··················· · · · · User Manual Safe Notice on the Li-Po Battery ·············· Charging Method of Li-Po Battery ············· Flyer Warnings ··························· Deﬁnition of the Flyer and the Controller ········ Flying Operation ·························· Function of the Flyer ···················...
Page 2: Important Statement
(4)Do not look straight into the highlighting nevigation LED lights , which may cause Important Statement discomfort to the eyes. Thank you for purchasing the item with Potensic. This is a toy drone, not a professional (5) Keep away form humid environment drone, but also need skills to control/play it.
Page 3: Charging Method Of Li-Po Battery
Deﬁnition of the Flyer and the Controller *Use Potensic original charger only. *Check the charger wire, plug, fuselage and other components on a regular basis to Name of Parts make sure they are in good condition. If any of those parts damaged, please do not use them until they are repaired.
Page 4 1. Antenna Transmit Signal to the drone Replace/Install the Drone Battery 1.Open the bottom battery cover of the drone(Picture 1). 2. Side Lights On/Off Turn on or turn off the side lights of the drone 2.Take out the battery carefully, avoid using too much force,it may damage the power 3.
Page 5: Flying Operation
Calibration Instruction Please follow the below steps to calibrate the drone if the drone wouldn't hover after taking off, and can not be adjusted by trim button and cause difﬁcult operation. 1.Turn off the drone switch and then turn off the transmitter switch. 2.Turn on the transmitter switch, then power on the drone switch and put it on the horizontal ground, after successful frequency piaring, press the ﬁp button (Picture11), you will hear "beep,beep,beep"...
Page 6: Function Of The Flyer
4.Forwards/Backwards Flying Function of the Flyer 1.Take Off: Turn on the transmitter and then power on the drone, push the left throttle to the utmostcontrol distance and then to the low end, release the throttle, the side Push the Left/Right/Forward/Back Flying lights stop ﬂash and stay solid, which indicates successful frequency pairing.
Page 7: Flip Mode
Flip Mode Method of Using the Phone APP Press ﬂip mode button of the transmitter(Picture 17) when ﬂying and the transmitter 1. Download and Install the APP:VS-UFO(Picture 19). This App is suitable for mobile phone with IOS8.0+ or Android 4.4+ system, please will issue sound of "beep beep...”which indicates the drone enters ﬂip mode.
Page 8: Icon Function Introduction
Icon Function Introduction Throttle Control Icon: 3.1 Phone Control Interface Icon Move the center touch point to adjust throttle response. Direction Control Icon: Reback Icon: Directly return to the entering interface of the APP by clicking this Icon. Take Photo Icon: Move the center touch point to control Click once to take photo, and saved directly on your phone.
Page 9: One-Hand Operation
One-hand Operation 3D Flip 1.Click speed adjustment icon to adjust the speed rate to 100%. 1. With the phone and App paired successfully, turn on joystick interface, click start icon to make the propeller spin, then the drone is ready to ﬂy. 2.Keep the drone at an altitude of no less than 2 meters to ensure that there are no obstacles around.
Page 10: Installation Blades
Problems Guidance Installation Blades Problem phenomenon Cause Solution F181 Blades Installation One or more blades One or more motors were damaged Swap with new motors 1.Remove the screws by counterclockwise rotate the screwdriver. stop spinging 2.Upwards pull out the blades. The larger white gear and the mental 3.Install the blades with the same rotate direction,then tighten the screws by clockwise blades spin slowly or...

This manual is also suitable for:

F181wh

Potensic F186WH User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Potensic F186WH

Summary of Contents for Potensic F186WH

This manual is also suitable for:

Table of Contents