Summary of Contents for J&M SpeedTender Hydraulic Jack
- Page 1 Manual HYDRAULIC JACK S E R V I C E A N D I N S T A L L A T I O N M A N U A L J&M Manufacturing Co, Inc 284 Railroad Street - P.O. Box 547 | Fort Recovery, OH 45846 | Ph: (419) 375-2376 | Fax: (419) 375-2708 www.jm-inc.com...
-
Page 3: Table Of Contents
Table Of Contents 4 ..................General Information 4 . -
Page 4: General Information
General Information TO THE OWNER: The purpose of this manual is to assist you in operating and maintaining your seed tender in a safe manner. Read it carefully. It furnishes information and instructions that will help you achieve years of dependable performance and help maintain safe operating conditions. If this machine is used by an employee or is loaned or rented, make certain that the operator(s), prior to operating: 1. -
Page 5: Safety Rules
Safety Rules ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be erased by an operator’s single careless act. In addition, hazard control and accident prevention are dependent upon the awareness, concern, judgment, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment. -
Page 6: Hydraulic Jack Parts
Hydraulic Jack Parts U-Bolts used only on A-Frame Description Part No. 3” x 24” x 1-1/2” Welded Cylinder (JD324) JM0019644 Seal Kit 3” x 24” Cylinder (JD324-1) (JD480) JM0037895 5/8”-11 x 1-1/2” Gr5 Z Hex Bolt JM0002103 5/8”-11 Gr2 Z Centerlock Hex Nut JM0002146 Outside Tube Weldment (Hydraulic Jack) JM0074387... -
Page 7: Hydraulic Jack Hydraulics Schematic
Hydraulic Jack Hydraulics Schematic Existing Hose Description Part No. 3/8” Male NPT x 3/8” Male JIC; 90 Degree Elbow JM0026121 Serviceable Pilot Check Valve JM0061684 Check Valve Cartridge JM0074412 3/8” Male NPT x 3/8” Male ORB; Straight JM0061726 3/8” x 25” Hydraulic Hose 25inch6M3K-6G-6FJX-6G-6FJX JM0049162 3/8”... -
Page 8: Set Up Instructions
Set Up Instructions Attach Hydraulic Jack to SpeedTender Gooseneck • Use (4) 5/8” x 1-1/2” hex bolts and (4) 5/8” centerlock hex nuts to fasten jack to mounting bracket. • Tighten hardware. A-Frame • Use (2) and (2) 5/8” centerlock hex nuts to fasten jack to side of A-Frame leg. 5/8”-11 x 6-1/16”... - Page 9 Set Up Instructions Move the Manual Canister • Remove both 1/4” x 1” hex bolts and hex nuts which fasten the manual canister to the SpeedTender. • Use the manual canister as guide and mark two points on the engine cover. Drill (2) 5/16” holes using the points as guides. •...
- Page 10 Set Up Instructions Install Hoses • Install the hoses as shown below. • Hose “16” is an “Existing Hose” connected to the “Bottom Port” • Unhook “16” from the bottom port of the valve bank, and connect directly to hose “15” shown below. •...
- Page 11 Set Up Instructions Test Functions • Ensure all fittings and hardware are tight. • Use zip ties to secure all hydraulic hoses to the SpeedTender. • Turn motor on. • Use control valve to raise and lower the hydraulic jack.