Related Manuals for Flash Furniture NAN-FSDC-02-BR-GG
Summary of Contents for Flash Furniture NAN-FSDC-02-BR-GG
- Page 1 PYRAM ID PATIO HEATER Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/NAN-FSDC-01-SL-GG.pdf Customer Service Email: CustomerExperience@belnickinc.com | Phone: 866-552-2810 NAN-FSDC-02-BR-GG / NAN-FSDC-01-SL-GG...
- Page 2 Owner ’s Manual Patio Heater...
-
Page 3: Safety Information
SAFETY INFORMATION Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so WARNING • The installation of this unit must adhere to local codes or Propane Storage and Handling Code, CSA B149.2. • THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY! This product shall be used outdoors, in a ventilated space and shall not be used in any enclosed a rea. - Page 4 • Do not disconnect any part while unit is in use. • Do not sto re a spare propane tank on or near this unit. • If the heating unit is indoors, detach the propane tank and leave outdoors. • •...
- Page 5 SAFETY INFORMATION 48" 48" 48" CAUTION: ANY M ATERIALS OR ITEMS THAT ARE STORED ABOVE, BESIDE OR UNDER THIS HEATER WHILE IN USE WILL BE SUBJECT TO RADIANT HE AT AND COULD BE SERIOUSLY DAMAGED. Combustible materials should not be within inches of the top of the unit, or within 48 inches around the entire unit.
- Page 6 HARDWARE Item Description Bolt M6x10 M6 nut Screw M5x10 Stud Wing nut Flat washer Bracket Screw 3/16” Knob Large flat washer Screw M4 X 8 Philips screwdriver Wrench AA Battery (1.5 V) Ground fixer Ground fixer screws Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list.
- Page 7 CONTENTS Item Description Reflector Top Plate Assembly Glass Tube Upper Support Protective Guard Black Silicone Ring Side Panel Front Panel Gas Hose & Regulator Middle Plate Control Box Assembly Lower Support Wheel Assembly Bottom Plate LP Tank Safety Strap ................................
- Page 8 ASSEMBLY INSTRUCTIONS 1.Attach the wheel assembly (M) to the bottom plate (N) using 4pcs bolt M6x10 (AA) and 4pcs M6 nut (BB). Ha r dware Used Bolt M6x10 M6 nut 2-1. Unscrew the ignition, load AA battery, tighten the ignition. 2-2.
- Page 9 Top Plate Assembly (B) 3. Insert upper support (D) to lower support (L) using 8pcs screw M5x10. Attach top plate assembly (B) to upper support (D) using 8pcs screw 3/16”. Hardware Used screw M5x10 Screw 3/16” 4. Attach the reflector (A) onto the top plate assembly (B).
- Page 10 5. Carefully install the glass tube (C) by lifting up and inserting through the center hole in the top plate assembly (B). Ensure the black silicone ring (F) is attached to the lower edge of the glass tube (C) as illustrated. Slide the To aid in installation glass tube (C) through the hole place black silicone...
- Page 11 7. Assemble three side panels (G) to heater using 18pcs screw 3/16”. Attention: Do not cover the front side where the control knob is. Hardware Used Screw 3/16” x 18 8.Install the knob (II) to screw M4x8 (KK) and large flat washer (JJ). Put the hooks of front panel (H) into the Note: Put screw (KK) through holes of bottom plate (N).
- Page 12 9. Place the propane gas tank (not included) on the base and secure the gas cylinder with LP Tank Safety Strap (O) 10. Turn the cylinder valve on the tank clockwise to close the propane tank. Attach the regulator (J) to the cylinder valve by turning the regulator coupling nut clockwise.
-
Page 13: Operation
OPERATION Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “off” position. Brush a soap and water mixture on all connections. Turn the gas supply on; if bubbles occur on any connection there may be a leak. -
Page 14: Maintenance
MAINTENANCE • Before performing any maintenance always disconnect propane gas tank. • Keep the heating area free and clear from combustible materials. • Visually inspect burner for obstructions and keep tank enclosure free and clear from debris. • Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner is completely cooled down. -
Page 15: Troubleshooting
TROUBLESHOOTING Problem Cause Solution The burner will not light. The burner injector is clogged. Clean the burner injector. There is low gas supply pressure. Call your gas supplier. The burner flame goes off There is low gas pressure. Call your gas supplier. immediately after ignition.