Joranalogue FILTER 8 Manual

Joranalogue FILTER 8 Manual

Multimode filter/8-phase oscillator

Advertisement

INTRODUCTION
Representing the cutting edge in modular
analogue voltage controlled filter (VCF) design,
Filter 8 offers more possibilities and higher
fidelity in 12 HP than ever before.
Starting from the classic OTA-style 4-pole
cascaded lowpass (LP) topology, Filter 8 features
separate LP outputs, each with their own
character.
Additional
achieved by pole mixing: 1-pole highpass, a
special band boost and notch response, phase
shifter and 4-pole bandpass. All outputs are
available simultaneously.
Key to Filter 8's performance is the innovative
resonant feedback circuit. By increasing the
resonance, all outputs will resonate at the filter
frequency, without any low frequency response
loss. At higher resonance levels, self-oscillation is
achieved, turning the module into an excellent
8-phase sine wave voltage controlled oscillator
(VCO) with temperature and switchable gain
compensation,
low
amplitude and accurate frequency tracking over
at least 5 octaves. At sub-audio frequencies,
Filter 8 can function as an 8-output voltage
controlled
slew
modifier
frequency oscillator (LFO).
Simultaneous exponential and linear frequency
modulation is possible, for classic FM tones or
chaotic modulation. A hold feature is also
provided, 'freezing' the output voltages manually
or under gate control. This is useful for halting
modulations, or as a sync-like effect at audio
frequencies. The dedicated 'ping' input allows
you to easily create crisp percussive sounds with
different timbres.
While rooted in the legacy of classic synthesisers,
Filter 8 provides a new approach to musical
signal generators and modifiers: instead of
simply a VCF, VCO, slew modifier or VCLFO, a
single analogue module can now be any of those,
and anything in between.
filter
responses
are
distortion,
constant
or
8-phase
low
MULTIMODE FILTER/8-PHASE OSCILLATOR
CONTENTS
In the Filter 8 box, you'll find:
 Product card, stating serial number and
production batch.
 16-to-10-pin Eurorack power cable.
 Mounting hardware: two black M3 x 6 mm
hex screws, two black nylon washers and a
hex key.
 The Filter 8 module itself, in a protective
cotton bag.
If any of these items are missing, please contact
your dealer or support@joranalogue.com.
1
FILTER 8

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FILTER 8 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Joranalogue FILTER 8

  • Page 1 Additional filter responses  The Filter 8 module itself, in a protective achieved by pole mixing: 1-pole highpass, a cotton bag. special band boost and notch response, phase If any of these items are missing, please contact shifter and 4-pole bandpass.
  • Page 2: Controls And Connections

    MULTIMODE FILTER/8-PHASE OSCILLATOR CONTROLS & CONNECTIONS 1 FREQUENCY RANGE SWITCH This switch determines over which frequency range Filter 8 will operate: low frequency (slew modifier/VCLFO) or audio frequency (VCF/VCO). 2 COARSE AND FINE FREQUENCY KNOBS The filter/oscillator frequency is determined by these knobs.
  • Page 3 To use Filter 8 purely as an oscillator, set the resonance to maximum and leave the input 7 RESONANCE MODULATION INPUT sockets unpatched.
  • Page 4 FILTER 8 MULTIMODE FILTER/8-PHASE OSCILLATOR 10 LOWPASS OUTPUTS 11 POLE-MIXING OUTPUTS These are the outputs from the different stages Using pole-mixing, additional filter responses are inside the 4-pole lowpass filter core. Frequencies derived from the standard lowpass stages. The above the filter frequency (also known as ‘cutoff’, first is a 1-pole highpass output, offering relatively gentle highpass filtering.
  • Page 5 ‘hold’ input. When the socket is used, the switch enables or disables the input. Filter 8’s hold input is uniquely designed to be driven reliably even from weak, slow, bipolar signals. It features Schmitt action, with a +2 V low...
  • Page 6 Should you find your Filter 8 to be out of tune, set it to oscillator mode (no input signal, maximum resonance, range switch to audio, compensation enabled). Set the coarse frequency knob to about 20 % of its range (9 o’clock), and the fine...
  • Page 7: Patch Ideas

    While this is not present on Add interest to your envelopes by processing Filter 8, the sound of an overdriven filter can still them through Filter 8. If the envelope has an be easily created, and with much expanded amplitude of above +5 V, attenuate it first and sonic possibilities, using feedback patching.
  • Page 8: Specifications

    SPECIFICATIONS SUPPORT MODULE FORMAT As all Joranalogue Audio Design products, Filter 8 is designed, manufactured and tested Doepfer A-100 ‘Eurorack’ compatible module 3 U, 12 HP, 30 mm deep (inc. power cable) with the highest standards, to provide the Milled 2 mm aluminium front panel with non- performance and reliability music professionals expect.
  • Page 9 With compliments to the following fine people, who helped to make Filter 8 a reality! Ben ‘DivKid’ Wilson Björn Jauss Boris Uytterhaegen Gregory Delabelle Jan D’Hooghe Jens Van Daele Lieven Stockx Sebastiaan Tulkens Everyone at Wired Electronics Filter 8 User Manual version 2018-10-30 Century Analogue Synthesis—Made in Belgium...

Table of Contents