Summary of Contents for Goepel Easy CON-1000Base-T1
Page 1
Easy CON - 1000Base-T1 Media Converter Manual (Original Documentation)
Page 2
The contents of the manual is subject to change without prior notice and is supplied for information only. Hardware and software might be modified also without prior notice due to technical progress. In case of inaccuracies or errors appearing in this manual, GOEPEL electronics GmbH assumes no lia- bility or responsibility.
Easy CON - 1000Base-T1 Table of Contents 1 Introduction ..........................1 1.1 Notes on this Document ..................... 1 1.2 Intended Use ........................1 1.3 EMC Protection Measures ....................2 1.4 EU Declaration of Conformity ....................2 1.5 General Safety Regulations ....................2 1.6 Liability and Warranty Exclusion ................... 2 1.7 Supplied Accessories ......................
Page 4
Easy CON - 1000Base-T1 List of Figures 1.1 Accessories ..........................3 2.1 Housing Top ..........................4 2.2 Housing Bottom and Outsides ...................... 4...
Page 5
Easy CON - 1000Base-T1 List of Tables 1.1 Symbols ........................... 1 2.1 Components of the Easy CON ...................... 4 2.2 Technical Specifications of the Easy CON ..................5 2.3 Technical Specifications of the Power Supply .................. 5 2.4 Pinout Socket "Automotive Ethernet" .................... 6 2.5 Pinout of the Adapter Cable ......................6 2.6 Keypad ............................
Simple mode-selection by keypad on the top of the device The system is not determined for other usage types than those listed here. Nevertheless, if you use it for any purpose other than stated, then GOEPEL electronics GmbH can not be held liable for result- ing damages.
EMC directives and standards. The system integrator is responsible for compliance with the EMC Direc- tive 2014/30/EU and national EMC laws for installed systems, system accessories and system compo- nents that have not been supplied or tested and approved by GOEPEL electronics as manufacturer of the equipment.
1 Introduction 1.7 Supplied Accessories As accessories to Easy CON you get: • 1 adapter cable RJ45 to D-Sub 9-pin • 1 USB 3.0 cable Figure 1.1 Accessories...
2 Technical Description 2 Technical Description 2.1 Overview Figure 2.1 Housing Top Figure 2.2 Housing Bottom and Outsides Position Designation Device Status Link Status Keypad Speed Mode LEDs Node 3 (Socket "USB") Socket "Supply" Placeholder nameplate Node 2 (Socket "Automotive Ethernet") Node 1 (Socket "Ethernet") Table 2.1 Components of the Easy CON The interfaces on the outside of the Easy CON are marked on the bottom of the device.
Peak to peak Weight Input connector type EU, US, UK, SAA Adapter included Table 2.3 Technical Specifications of the Power Supply The power supply can optionally be purchased to the Easy CON device via the GOEPEL electronics sales de- partment.
2 Technical Description 2.4 Status Indication The Easy CON provides various information about the operational status and status of both Ethernet links. 2.4.1 Device Status LED The Device Status LED indicates the following states: constantly WHITE : Device initialisation (after RESET) •...
2 Technical Description The right 100Mbit/s Phy Status LED (green) indicates the following states: constantly off : No link • constantly on : Link OK • flashing : Data traffic • 2.4.5 Speed Mode LEDs The Speed Mode LEDs (white) indicate the following states: Auto : Auto Negotiation •...
The PHY (Ethernet Physical Layer transceiver) 88Q2112 from Marvell is integrated into the Easy CON device. De- pending on the version, this PHY is revision A0 or A2. To check, which generation is installed in your Easy CON , you can contact GOEPEL electronics Support by indicating the serial number.
4 Service and Support 4 Service and Support 4.1 Spare Parts and Accessories If necessary, please contact our sales department: GOEPEL electronics GmbH ATS-Vertrieb Goeschwitzer Str. 58 / 60 D-07745 Jena Tel.: +49-3641-6896-508 E-Mail: ats.sales@goepel.com http://www.goepel.com...
If the warranty has expired, we will of course also repair your test system in accordance with our general installation and service conditions. If necessary, please contact our support service: GOEPEL electronics GmbH ATS-Support Goeschwitzer Str. 58 / 60 D-07745 Jena Tel.: +49-3641-6896-597...
5 Disposal 5 Disposal 5.1 Disposal of used Electrical / Electronic Equipment The device implements the following EU directives: • 2012/19/EU (WEEE) Waste Electrical and Electronic Equipment and • 2011/65/EU on the restriction of the use of certain hazardous substances in electronic equipment (RoHS directive) At the end of the life of the device, this product must not be disposed of with other household waste.