Advertisement
Quick Links
1. ADJUST
DOLLY AXLES
2. PROPER
AXLE
ADJUSTMENT
Overextending your axle results in increased stress on axle and dolly, which could result in personal injury!
3. PREPARE
DOLLY AXLES
& SIDE FRAMES
FOR MORE INFORMATION: www.intheditch.com | (208) 587-7960 | sales@intheditch.com
TM
IT IS THE OPERATOR'S RESPONSIBILITY TO INSPECT DOLLIES BEFORE EACH USE. INSPECTION SHOULD BE A PART OF THE OPERATOR'S DAILY
!
CIRCLE CHECK OF THE VEHICLE.
!
FAILURE TO FOLLOW THE SAFETY GUIDELINES LISTED MAY RESULT IN VOIDING ANY APPLICABLE WARRANTY, SERIOUS BODILY INJURY, OR DEATH.
IT IS VERY IMPORTANT THAT YOU PROPERLY FILL OUT YOUR PRODUCT REGISTRATION FORM AT REGISTRATION.INTHEDITCH.COM TO REGISTER YOUR EQUIPMENT.
BY SUBMITTING THE INFORMATION WITHIN 15 DAYS OF YOUR PURCHASE, YOUR WARRANTY WILL BE VALIDATED, ENSURING THAT YOUR EQUIPMENT WILL BE
!
PROTECTED SUBJECT TO THE TERMS AND CONDITIONS SET OUT HEREIN. IN THE EVENT WE NEED TO CONTACT YOU CONCERNING YOUR REGISTERED EQUIPMENT,
PRODUCT UPDATES, SERVICE BULLETINS, OR PRODUCT RECALLS, THE INFORMATION YOU HAVE PROVIDED ON THE PRODUCT REGISTRATION FORM WILL ENSURE
YOUR IMMEDIATE NOTIFICATION. DO YOUR PART AND LET US HELP YOU BY FILLING OUT YOUR PRODUCT REGISTRATION FORM.
DOLLY OPERATION
Depress
Extend axles to the minimum length required to span the width of the vehicle, ensuring
the snap button re-engages at the extended setting.
4" or less
4" or less
PROPER AXLE
ADJUSTMENT
Top View
Place the dolly axles and side frames on the
ground in the configuration shown below with
dollies centered and parallel to vehicle tires.
TM
LOADING
Extend
GOOD
More than 4"
More than 4"
IMPROPER AXLE
ADJUSTMENT
SNAP BUTTON MUST BE FULLY ENGAGED BEFORE USE OR TRANSPORT
FAILURE TO ENGAGE SNAP BUTTON MAY RESULT IN PERSONAL INJURY
SERIES
DOLLIES
Engaged
Snap Button
BAD
Top View
WARNING:
PAGE 1 OF 6
ITD0791
Advertisement
Related Manuals for In The Ditch X Series
Summary of Contents for In The Ditch X Series
- Page 1 SERIES DOLLIES DOLLY OPERATION LOADING Depress Engaged Extend Snap Button 1. ADJUST DOLLY AXLES Extend axles to the minimum length required to span the width of the vehicle, ensuring the snap button re-engages at the extended setting. 2. PROPER AXLE GOOD More than 4”...
- Page 2 4. POSITIONING DOLLY SIDE Cam-Locks in detents Disengage FRAMES Storage Position with tires on ground Cam-lock A.Rotate cam locks to release tires from storage position. B. Allow wheel pivot arms to rotate until the tires hit the ground. C. Position the dolly side frames while the cam locks stay in detents. 6.
- Page 3 ALWAYS KEEP BOTH HANDS ON THE BREAK-OVER BAR WHILE RAISING THE DOLLY! EXTRA CAUTION SHOULD BE USED IF LOADING OR UNLOADING ON UNEVEN PAVEMENT, LOOSE GRAVEL, SNOW, WATER, OR ICE! THE SAME OPERATOR MUST LOAD AND UNLOAD THE DOLL. CHANGES IN OPERATORS WILL RESULT IN UNFAMILIAR LOADS. WHICH MAY RESULT IN SERIOUS INJURY! Engaged Disengaged...
- Page 4 UNLOADING THE SAME OPERATOR MUST 1. REMOVE 3. INSERT LOAD & UNLOAD THE DOLLY. CHANGES IN OPERATORS WILL RATCHET STRAPS BREAK-OVER BAR RESULT IN UNFAMILIAR LOADS, WHICH MAY RESULT IN SERIOUS INJURY. With the vehicle secured in the wheel lift of the tow truck, remove ratchet straps on dolly.
-
Page 5: Tips And Tricks
TIPS & TRICKS THE CRUNCH ZONE A simple little tip when you find yourself in the crunch zone. The crunch zone is anytime you are up against an obstacle such that you cannot fully raise the dolly using the break-over bar. The following are the steps to get out of the “Crunch Zone”... -
Page 6: Tie Downs
STEP 7 SECURE WITH TIE DOWNS 7. Load dolly as normal and attach tie downs. WALKING THE DOLLY With the ability to lock the dolly wheels in the stowed position, the ITD dollies have the unique feature of “walking” using the break-over bar.