Advertisement
5.3.
OPERATING THE AUTO VALET MACHINE
WARNING! Test materials for colour fastness, test on an area not normally noticed (i.e. under a car seat).
#
5.3.1. Plug the machine into the mains power supply.
5.3.2. Switch the BLACK MOTOR SWITCH "ON" to start the vacuum (fig 20).
DO NOT PRESS THE PISTOL TRIGGER AT THIS STAGE.
5.3.3. Place the cleaning head on the material to be cleaned and press the
GREEN PUMP SWITCH "ON" (fig 20).
5.3.4. Press the trigger (fig 21) and move the tool slowly across the material by drawing
the head towards you. Work in small areas at a time. The pump produces pressure which
forces detergent into the fabric pile. During this first pass approximately 60% of the
dirty fluid will be sucked back up into the waste tank.
5.3.5. Make a second pass WITHOUT pressing the trigger (fig 22). This will extract
the remainder of the fluid from the material, leaving the fabric almost dry.
5.3.6. Allow the fabric, or upholstery to dry completely before walking, or sitting on it.
6. AFTER USE
6.1.
Remove the plug from the mains.
6.2.
Remove the motor head.
6.3.
Empty tank of dirty liquid into a suitable waste receptacle or drain.
6.4.
Empty and rinse out the detergent tank.
6.5.
Fill the detergent tank with clean water, and flush the system by operating into a bucket, or drain.
Continue to flush until all the dirty fluid has been expelled.
6.6.
Rinse the tank clean.
6.7.
Wipe the tank and fittings and leave to dry.
6.8.
Check the filter at the end of the detergent pick-up pipe to ensure it is not clogged.
If it is, remove and rinse under running water (fig 23).
6.9.
Remove the main motor head filter and clean as in chapter 7.
NOTE: Before next use, check that the correct filter is fitted for the job you are going to perform.
Use of wrong filter will invalidate your warranty.
7. MAINTENANCE
# # WARNING ENSURE YOU DISCONNECT FROM THE MAINS POWER SUPPLY BEFORE OPENING THE UNIT, OR CARRYING OUT ANY MAINTENANCE.
7.1.
General Machine Maintenance.
7.1.1. Remove plug from the mains power supply before carrying out service or maintenance.
7.1.2. Regularly check and clean the filter connected to the end of the detergent pick-up pipe by running under a cold water tap (fig 23).
7.1.3. After having used the appliance as a wet cleaner, empty the contents. Clean and dry the tank and accessories to avoid scaling.
7.1.4. Periodically check to ensure the valet machine and accessories are not blocked or damaged, and are in good working order.
Any damaged parts must be replaced immediately. Blocked hoses or tubes will impair performance and may damage the machine.
Such damaged motor units returned for repair will not be accepted under the warranty and may incur expensive repair bills.
7.2.
Cleaning Filters.
For optimum performance, all types of filters should be cleaned regularly. Unclean, damaged, or wrongly fitted filters will impair your
machine's performance and may damage it. Such damaged motor units returned for repair will not be accepted under the warranty, and
may incur expensive repair bills. Never use the machine without a filter. Dirt in motor will cause failure and will invalidate the warranty.
7.2.1. CLEANING FOAM FILTER. Used for wet cleaning.
a)
Wash the foam filter in a suitable container of lightly soapy water (DO NOT use solvents).
b)
Allow to dry before use. Check to see if the filter is worn, in which case it must be replaced with a new one.
7.2.2. CARTRIDGE FILTER CLEANING. Used for dry cleaning.
a)
Remove the filter cartridge from the motor head (fig 24).
b)
Regularly clean the cartridge filter by dusting with a soft bristle brush (fig 25).
c)
DO NOT get the filter wet or wash filter in water or any other cleaning liquids as the filter will disintegrate (fig 26).
NOTE: Inspect filters regularly, if large amounts of un-removable deposits are obvious, or if the filter is worn or damaged it must be replaced.
We recommend that you keep a spare of each filter.
fig 24
fig 25
fig 20
fig. 21
fig 23
fig 26
VMA911 - VAM912 - 4 - 051006
fig. 22
Advertisement
