Related Manuals for TCS IMM2300
Summary of Contents for TCS IMM2300
- Page 1 Product information Video indoor station for hands-free talking IMM2300 TCS TürControlSysteme AG Subject to technical changes. Mail: info@tcsag.de PI_IMM2300_Art0031160-uk.doc...
-
Page 2: Table Of Contents
09/2011 Table of contents Scope of delivery ......................... 3 Safety instructions........................ 3 General on the conduit in TCS video systems ..............3 Term ..........................3 6-wire operation........................ 3 Principle loop resistance ....................4 Measurement loop resistance ..................4 Device overview ........................5 Technical data ........................ -
Page 3: Scope Of Delivery
With suitable requirements to protect against lightning, it has to be ensured that a vol- tage of each 32 V DC is not exceeded at the TCS:BUS wires a and b. General information on the cable routing in TCS video systems... -
Page 4: Principle Loop Resistance
All other devices do not disturb the measurement and can stay connected. short-circuit a, b here 8 Ohm: around 65 m distance AS-VS by 0.6 mm diameter around 115 m distance AS-VS by 0.8 mm diameter TCS TürControlSysteme AG Subject to technical changes. Mail: info@tcsag.de PI_IMM2300_Art0031160-uk.doc... -
Page 5: Device Overview
I(Pmax) = 155 mA video module TFT-color module screen diagonal 2.4 inch resolution 480 x 234 pixel video signal entrance symmetrical 1 Vss FBAS Only video 6-wire technique possible! TCS TürControlSysteme AG Subject to technical modifications. Mail: info@tcsag.de PI_IMM2300_Art0031160-uk.doc... -
Page 6: Display And Control Elements
Factory setting: AS threshold = 0, limit of the AS address areas can be adjusted with the device configurator configo™ or set ex works on requirement. ** WE = factory setting *** if the light switch function in the front-door station is activated TCS TürControlSysteme AG Subject to technical changes. Mail: info@tcsag.de PI_IMM2300_Art0031160-uk.doc... -
Page 7: Application
The IMM 2300 is an indoor station for hands-free talking, manually controlled simplex communication can be activated It is designed for surface-mounting. It is suitable for the operation in TCS video systems and combined audio/video systems. Brief description Basic module... -
Page 8: Mounting And Installation
Position the flush-mounted sock- et behind the cable gland. Install the lower cover at the at- tachement holes with suitable position screws on the wall (as shown in flush- the illustration). mounted socket TCS TürControlSysteme AG Subject to technical changes. Mail: info@tcsag.de PI_IMM2300_Art0031160-uk.doc... -
Page 9: Connection Of Cables
Make sure that the plug-terminal is plugged in accordance to the illustration! pluggable screw terminal Terminating resistor Remove the terminating resistor if the device is not installed at the end of a TCS:BUS video strand. TCS TürControlSysteme AG Subject to technical modifications. Mail: info@tcsag.de PI_IMM2300_Art0031160-uk.doc... -
Page 10: Snapping-On The Upper Cover Of The Modules
Insert a screwdriver (around 7 mm) with slight pressure straight into this opening. 2. The upper covers can be re- moved at the underside. 3. Lift the upper cover of both upper locking brackets. TCS TürControlSysteme AG Subject to technical changes. Mail: info@tcsag.de PI_IMM2300_Art0031160-uk.doc... -
Page 11: Note On Power Supply
In case of power supply with BVS20 or BVS100 additionally use NGV1011! Wiring example J1 must be plugged, if the device is installed at the end of a TCS:BUS video strand. Remove J1, if the device is not installed at the end of a TCS:BUS video strand. -
Page 12: Commissioning
Note: The AS-addresses of the front-door stations should be allocated via Service Device. For more information see service information within the TCS Installer 5 / 4 (version 1) or TCS Installer 7 / 4 (version 2). TCS TürControlSysteme AG Subject to technical changes. -
Page 13: Volume Internal Communication
The programming takes always place in four steps: Initiate the programming Preselection Final selection End the programming Initiate the programming press call OFF button (8 sec), until release a short acknowledgement tone sounds TCS TürControlSysteme AG Subject to technical modifications. Mail: info@tcsag.de PI_IMM2300_Art0031160-uk.doc... - Page 14 / lift handset control function 8 (at function key) switch on automatic hands-free talking after internal call (if switched off) or switch off (if switched on) TCS TürControlSysteme AG Subject to technical changes. Mail: info@tcsag.de PI_IMM2300_Art0031160-uk.doc...
- Page 15 BVS programming mode of the system. Carry out the steps 1 to 4. Switch off program- ming mode of the system. reload factory settings press door release button for 8 sec TCS TürControlSysteme AG Subject to technical modifications. Mail: info@tcsag.de PI_IMM2300_Art0031160-uk.doc...
-
Page 16: Programming With The Service Device Tcsk-01
End the programming Press call OFF button short or automatically, if no button is pressed for more than 8 sec. Programming with the Service Device TCSK-01 For further information see TCS Installer, 7 Service Device TCSK-01 or programming handbook TCSK-01. searching telephones... -
Page 17: Operation
* When first adjusting the ring tone, also the second front-door station is fitted with the same ring tone as the first one. If the ring tone is adjusted separately (2b) for the second front-door station, it always has to be set independently. TCS TürControlSysteme AG Subject to technical modifications. -
Page 18: Faq
Only with loop through signals are not the last video component of the installed properly. strand requires a terminating re- sistor TCS TürControlSysteme AG Subject to technical changes. Mail: info@tcsag.de PI_IMM2300_Art0031160-uk.doc... - Page 19 Two video sources interfere. Please remove the second video are visible. source from the strand. If necessary, connect this second video source via a video switch to the existing TCS:BUS. TCS TürControlSysteme AG Subject to technical modifications. Mail: info@tcsag.de PI_IMM2300_Art0031160-uk.doc...
-
Page 20: Cleaning
Remove stronger stains with a mild plastic cleaner. Service Please send your questions and inquiries to hotline@tcsag.de headquarters TCS TürControlSysteme AG, Geschwister-Scholl-Str. 7, 39307 Genthin / Germany Tel.: +49 (0) 3933/879910, FAX: +49 (0) 3933/879911, www.tcsag.de TCS TürControlSysteme AG Subject to technical changes. Mail: info@tcsag.de...