Related Manuals for GSi PNEG-765
Summary of Contents for GSi PNEG-765
- Page 1 In-Line Intermediate Discharge Gates Installation Manual PNEG-765 Date: 01-29-14 PNEG-765...
- Page 2 PNEG-765 In-Line Intermediate Discharge Gates...
-
Page 3: Table Of Contents
Cut Out Discharge Hole in Trough Bottom .................... 9 Manual Gate Installation ........................10 Motor Driven Gate Installation ......................11 Install Gate Frame to Trough ......................15 Chapter 4 Wiring Diagram ...........................16 Typical Wiring Diagram ........................16 Chapter 5 Warranty ..............................17 PNEG-765 In-Line Intermediate Discharge Gates... -
Page 4: Chapter 1 Safety
CAUTION, used with the safety alert symbol, indicates a CAUTION hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE is used to address practices not related to NOTICE personal injury. PNEG-765 In-Line Intermediate Discharge Gates... -
Page 5: Safety Instructions
Electrical controls should be installed by a qualified electrician and must meet the standards set by the National Electrical Code and all local and state codes. Disconnect and lock out all power sources before installing wires/cables or servicing equipment. Electric Shock Hazard PNEG-765 In-Line Intermediate Discharge Gates... - Page 6 A respirator may be needed to prevent breathing potentially toxic fumes and dust. Wear a hard hat to help protect your head. Hard Hat Wear appropriate fall protection equipment when working at elevations greater than six feet (6'). Fall Protection PNEG-765 In-Line Intermediate Discharge Gates...
-
Page 7: Chapter 2 Decal
The GSI Group 1004 E. Illinois St. Assumption, IL. 62510 Phone: 1-217-226-4421 WARNING Moving side plate. Auto equipment can start at any time. Disconnect and lockout before servicing. GSI Group 217-226-4421 DC-1248 DC-1248 (Not to scale.) PNEG-765 In-Line Intermediate Discharge Gates... -
Page 8: Chapter 3 Installation
16.00 30.00 68.125 1214 12.00 30.00 68.125 1614 16.00 30.00 68.125 2114 21.00 30.00 68.125 1420 14.00 36.00 81.125 1620 16.00 36.00 81.125 2020 20.00 36.00 81.125 2620 26.00 36.00 81.125 3220 32.00 36.00 81.125 PNEG-765 In-Line Intermediate Discharge Gates... -
Page 9: Cut Out Discharge Hole In Trough Bottom
14.00 36.125 2.00 1620 16.00 36.125 2.00 2020 20.00 36.125 2.00 2620 26.00 36.125 2.00 3220 32.00 36.125 2.00 2626 26.00 36.125 2.00 3226 32.00 36.125 2.00 3232 32.00 36.125 2.00 3632 36.00 36.125 2.00 PNEG-765 In-Line Intermediate Discharge Gates... -
Page 10: Manual Gate Installation
2. Manual gates up to 16" wide are fitted with a single rack. Manual gates larger than 16" wide have a double rack. 3. The slide gate plate rides on 1-3/8" double shielded radial bearings for smooth operation. Figure 3C Ref # Description Hand Wheel Shaft Gate Frame PNEG-765 In-Line Intermediate Discharge Gates... -
Page 11: Motor Driven Gate Installation
Install Motor Bracket 1. Install the motor bracket to the gate. Then attach the motor to the bracket as shown in Figure using the provided hardware. Figure 3D Ref # Description Motor Shaft Motor Bracket Key Way PNEG-765 In-Line Intermediate Discharge Gates... - Page 12 5. Motor driven gates are available in both TEFC and explosion proof configurations. Figure 3E Figure 3F Ref # Description Switch Bracket Limit Switch PNEG-765 In-Line Intermediate Discharge Gates...
- Page 13 Install Limit Switch (Continued) Figure 3G Figure 3H EXPLODED VIEW shown without side for clarity. Ref # Description Ref # Description Limit Switch Side view with side removed clarity. Actuator Arm Slide Gate Tripper Block Cover PNEG-765 In-Line Intermediate Discharge Gates...
- Page 14 3. Installation Install Limit Switch (Continued) Figure 3I GATE CLOSED POSITION shown without side for clarity. Figure 3J GATE OPENED POSITION shown without side for clarity. Ref # Description Actuator Arm Tripper Block Slide Gate PNEG-765 In-Line Intermediate Discharge Gates...
-
Page 15: Install Gate Frame To Trough
4. Adjust the carry-over bar frame so that the top of the carry-over bars are flush to the inside surface of the intermediate bottom. NOTE: Failure to properly adjust the carry-over bar frame will cause severe damage to the chain and/or gate. Figure 3K Ref # Description Trough Section Gate Assembly Carry-Over Bars PNEG-765 In-Line Intermediate Discharge Gates... -
Page 16: Chapter 4 Wiring Diagram
4. Wiring Diagram Typical Wiring Diagram OPEN CLOSE STOP Remove internal jumpers 3 to 6, 5 to 7. Open position switch Closed position switch Break for momentary operation PNEG-765 In-Line Intermediate Discharge Gates... -
Page 17: Chapter 5 Warranty
14 months from arrival at port of discharge, whichever is earlier. The end-user’s sole remedy (and GSI’s only obligation) is to repair or replace, at GSI’s option and expense, products that in GSI’s judgment, contain a material defect in materials or workmanship. - Page 18 Authorities having jurisdiction should be consulted before installations are made. GSI Group 1004 E. Illinois St. Assumption, IL 62510-0020 Phone: 1-217-226-4421 Fax: 1-217-226-4420 www.gsiag.com GSI is a worldwide brand of AGCO Corporation. Copyright © 2014 by GSI Group Printed in the USA CN-310201...
Need help?
Do you have a question about the PNEG-765 and is the answer not in the manual?
Questions and answers