Warn Ascent-HD 10718X Installation Instructions Manual
Warn Ascent-HD 10718X Installation Instructions Manual

Warn Ascent-HD 10718X Installation Instructions Manual

Front bumper for ford sd f450/f550 2017-20

Advertisement

Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have
provided installation and operating instructions and other information on labels and in this guide. This information
alerts you to potential hazards that could hurt you or others. It is not possible to warn you about all potential hazards
associated with this product, you must use your own good judgment.
CARELESSINSTALLATION AND OPERATIONCANRESULTINSERIOUSINJURY OR EQUIPMENTDAMAGE. READ AND
UNDERSTANDALLSAFETYPRECAUTIONSANDOPERATINGINSTRUCTIONSBEFOREINSTALLINGANDOPERATING
THIS PRODUCT.
This guide identifies potential hazards and has important safety messages that help you and others avoid personal injury
or death. WARNING and CAUTION are signal words that identify the level of hazard. These signal words mean:
WARNING signals a hazard that could cause serious injury or death, if you do not follow recommendations.
signals a hazard that may cause minor to moderate injury, if you do not follow recommendations.
This guide uses NOTICE to call attention to important mechanical information, and Note: to emphasize general
information worthy of special attention.
Always Know Your Winch. Take time to fullyreadtheInstructionsand/orOperationsGuide,and/orBasicGuidetoWinchingTechniques,inorderto understand your winch and its operations.
Never work under vehicle before properly securing vehicle.
Always use appropriate and adequate care in lifting components into place.
Never work under vehicle before properly securing vehicle.
Always use appropriate and adequate care in lifting components into place.
Never use a jack to support the vehicle.
Always use jack stands in pairs to support the vehicle.
Always use jacks or jack stands only on a hard, stable, and level surface.
Never exceed the rated capacity of a jack or jack stands.
Always verify that the parking brake is set, the transmission is in park(automatic)or reverse(manual)and the rear wheels are blocked before working on vehicle.
Never work under vehicle before properly securing vehicle.
Always use appropriate and adequate care in lifting components into place.
Always insure components will remain secure during installation and operation.
Always tighten all nuts and bolts securely, per the installation and operation.
Always perform regular inspections and maintenance on the winch, winch mount and related hardware.
Always replace all worn or damaged parts before operating.
Never operate this WARN product with damaged or missing parts.
Always use extreme caution when drilling on any vehicle. Make sure that all fuellines,brakelines,electricalwires,andotherobjectsarenotpuncturedordamagedwhen/ if drilling on the vehicle .Thoroughl y
inspect the area to be drilled(on both sides of material)prior to drilling, and relocate any objects that maybe damaged. Failure to inspect the area to be drilled may result in vehicle damage, electrical
shock, fire or personal injury.
Always use extreme caution when cutting and trimming during fitting.
Always wear safety glasses when installing this kit. A drilling operation will cause flying metal chips. Flying chips can cause eye injury.
Always remove jewelry and wear eye protection.
Never lean over battery while making connections.
Never route electrical cables across any sharp edge, through or near moving parts, near parts that become hot.
WARN INDUSTRIES, INC. 12900 S.E. Capps Road,
Clackamas, OR USA 97015-8903, 1-503-722-1200, FAX: 1-503-722-3000
Customer Service: 1-800-543-9276
Dealer Locator Service: 1-800-910-1122
International Fax: 1-503-722-3005
©2019 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
Ascent-HD Front Bumper
Application: 2017-20 Ford SD F450/F550
G E N E R A L S A F E T Y P R E C A U T I O N S
W A R N I N G
IMPACT AND MOVING PARTS ENTANGLEMENT HAZARD
Failure to observe these instructions could lead to severe injury or death
Read installation and operating instructions thoroughly.
Part Number: 10718X
1
CAUTION
107229A0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Ascent-HD 10718X and is the answer not in the manual?

Questions and answers

Summary of Contents for Warn Ascent-HD 10718X

  • Page 1 This information alerts you to potential hazards that could hurt you or others. It is not possible to warn you about all potential hazards associated with this product, you must use your own good judgment.
  • Page 2 (N.m) lb-ft (N.m) 1/4" (11) 5/16" (23) (4.5) 3/8" (40) (7.5) 7/16” (66) (18) 1/2" (100) (37) 9/16” (144) 5/8" (200) 3/4” (364) ©2019 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc. 107229A0...
  • Page 3 M14-2 Hex head nut 100974 M14 Lock washer 100511 M14 Flat washer 100601 ½-13 Hex head nut 4.10 100604 ½” Lock washer 4.11 100606 ½” Flat washer ©2019 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc. 107229A0...
  • Page 4 I N S T A L L A T I O N I N S T R U C T I O N S Start by removing four bolts around tow hook on each side of vehicle. This will require an 18mm socket. (Fig. 1) Figure 1 Next, with the help of someone holding the bumper in place, remove the four 15mm bolts from the bumper supports on both sides of vehicle.
  • Page 5 Next, using 18mm socket remove the two nuts on either side of the frame attaching frame horns to frame. Set bolt strips and nuts aside as they will be used in the installation of WARN bumper. (Fig. 4) Figure 4...
  • Page 6 I N S T A L L A T I O N I N S T R U C T I O N S Optional: If you are installing a winch with this bumper installation, do so now. Use the bracket or clamps supplied with the winch to mount the control pack;...
  • Page 7 With the bumper in place loosely install using the bolt strips and 1/2" flat and lock washers with nuts (50246-HW). (Fig.8) Figure 8 Next hold the bumper into desired position on the truck. NOTE: WARN recommends a MINIMUM gap of 3/8” at the outer fenders and headlights to prevent paint damage in normal operation.
  • Page 8 I N S T A L L A T I O N I N S T R U C T I O N S M A I N T E N A N C E / C A R E Inspect all parts on the winch, winch mount, and related hardware prior to each use.

Table of Contents