Advertisement
Quick Links
Advertisement
Related Manuals for red roo SHP400
Summary of Contents for red roo SHP400
- Page 1 No. : 634 : Red Roo SHP400 Stump Grinder Scan Code GT622 SHP400 GT622 StumP grinder GARDEN TILLER Operation, Safety & Maintenance Instructions ™ Commercial Environmental Equipment Commercial Environmental Equipment Online Demonstration Available at: www.redroo.com/products/stumpgrinder...
- Page 2 Congratulations! You are now the proud owner of the Red Roo Model Dear Valued Customer SHP400 Stump Grinder. Please take a moment of your time to look over the Stump Grinder. Please take a moment of your time to look over the following information.
-
Page 3: Table Of Contents
WARRANTY POLICY WARRANTY POLICY WARRANTY POLICY WARRANTY POLICY RED ROO SALES & SERVICE COMPANY PTY. LTD. RED ROO SALES & SERVICE COMPANY PTY. LTD. RED ROO SALES & SERVICE COMPANY PTY. LTD. RED ROO SALES & SERVICE COMPANY PTY. LTD. -
Page 4: About This Manual
Red Roo product. By following these guidelines, you may look forward to years of reliable service from your Red Roo. Information is categorised and denoted by the forward to years of reliable service from your Red Roo. Information is categorised and denoted by the forward to years of reliable service from your Red Roo. -
Page 5: Operating Instructions
Keep rotary hoe. Keep all clothing away from moving of your Red Roo product. By following these guidelines, you may look NEVER allow children or untrained adults to operate the stump grinder. away from moving parts. Item could b vice from your Red Roo. - Page 6 This machine has a high centre of gravity. Use extreme care when operating it on an uneven surface. DUAL WHEEL KIT IS AVAILABLE AS AN OPTIONAL ACCESSORY OPERATION INSTRUCTIONS Remove the stump grinder from its carrying vehicle or trailer. Use caution Familiarize yourself with the machine and its controls.
- Page 7 DO / CORRECT DO / CORRECT DO / CORRECT DO NOT! / INCORRECT DO NOT! / INCORRECT NOTE: SELF PROPELLED UNITS. For more precise control of the wheel while grinding it can be easier to operate one control lever at a time, alternating between the two, making the machine walk, from side to side.
- Page 8 1. aIr fIlter MaIntenance Is crItIcal on stuMp grIndIng MachInes. dIrt IngestIon WIll not be Warranted by the engIne Manufacturer or red roo sales and servIce follow these steps: A. Unhook the two retaining clips and remove the end cap from the air cleaning housing.
- Page 9 2. oIl and aIr fIlter MaIntenance and stayIng WIthIn the lIMIts of the angle of operatIon Is also crItIcal on stuMp grIndIng MachInes. starvIng the engIne for oIl WIll not be Warranted by the engIne Manufacturer or red roo sales and servIce pty. ltd.
- Page 10 – Daily to 200 hours CHECK/ADJUST BELT TENSION CUTTER WHEEL DRIVE BELTS HYDRAULIC PUMP BELT TENSION - Check tension and deflection at midpoint of belt - if it slips, it’s too loose. Tighten. - A new belt should be tensioned to deflect 12mm when a 3-4kg force is applied. - To tension belts, slacken pump mount bolts and slide pump back until correct BELT ADJUSTING BOLT tension on the belt is achieved.
- Page 11 HYDRAULIC OIL TANK Check hydraulic oil level daily. The SHP400 hydraulic tank is equipped with a site glass that shows the level of hydraulic oil. Do not overfill this tank, allow for the expansion of hydraulic fluid. This machine is equipped with Castrol Hyspin 68 hydraulic oil at the time of manufacture.
- Page 12 Detergents that recommend the use of gloves when handling should be avoided as this as a good indication that the detergent is too harsh and therefore unsuitable for cleaning your powder coating. Although some strong solvents are recommended for removing grease, or other stubborn residues these may be harmful to the extended life of the powder coated surface.
- Page 13 REPLACING STUMPGRINDING TEETH BEFORE YOU REPLACE ANY CUTTER Loosen Turn 120° Tighten to 25ft/lbs FOR ALL MOVING PARTS TO STOP. BEFORE YOU REPLACE ANY CUTTERS YOU MUST TURN THE ENGINE OFF AND WAIT MAKE SURE ALL OF THE CUTTERS AR REPLACING STUMPGRINDING TEETH FOR ALL MOVING PARTS TO STOP.
- Page 14 TRANSPORTING THE MACHINE loadIng If the machine is loaded using steep ramps use extreme caution. This unit has a high centre of gravity. OPTIONAL DUAL WHEEL KIT IS AVAILABLE tIe doWn The machine is equipped with a pin lock and hole through the cutter wheel cover. This pin lock is designed to connect to a purpose built bracket fitted to the trailer or truck used to carry the machine.
- Page 15 GROUND DRIVE CONTROLS Ground drive is achieved by two independent drive tyres driven by hydraulic motors. Each of the motors has its own control lever on the handle bar. 1. FORWARD: Push BOTH levers forward equally: machine moves straight ahead. 2.
-
Page 16: Troubleshooting
TROUBLE SHOOTING ENGINE PROBLEM CAUSE SOLUTION Engine won’t turn over Flat battery Check condition of battery and replace if necessary. Dirty battery terminals Disconnect battery cables and clean terminals. Defective ignition switch Replace switch. Defective starter solenoid Replace solenoid. Electric Clutch is turned on Turn clutch switch to ‘off’... - Page 25 1 x 0401-0034 (Large) 0401-0036 (Small) 3 x 0401-0001 1 x 0401-0095 1 x 0401-0081 24129 CMS100 Chipper Mulcher Shredder Manual.indd 23 1 x 0401-0065 1 x 0401-0052 1 x 0401-0078 1 x 0401-0070 1 x 0401-0074 1 x 0401-0038 1 x 0401-0049 1 x 0401-0077 1 x 0401-0050...
- Page 26 PLEASE VISIT AND HAVE A LOOK AT OUR COMPLETE RANGE OF PRODUCTS GT622 GARDEN TILLER RED ROO A LEADER IN Operation, Safety & Maintenance Instructions COMMERCIAL ENVIRONMENTAL EQUIPMENT ™ Commercial Environmental Equipment...
-
Page 27: Warranty Policy
Service Company, P/L, herein referred to as "MANUFACTURER", will, at its option, repair or replace for the original purchasers of new Red Roo equipment, free of charge, any part, or parts of the unit (excluding Power Unit, warranty coverage provided by respective engine manufacturer), found upon inspection and testing by a Factory Authorised Agent, or by the Factory at Keysborough, Victoria, to be defective in material or workmanship or both under normal operating conditions;... - Page 28 GT622 GARDEN TILLER You alone know the operational demands and special conditions affecting the equipment in your situation and therefore assume the responsibility for developing, carrying out, and enforcing the safety concepts which apply to your own operation to effect the greatest safety peration, Safety &...
Need help?
Do you have a question about the SHP400 and is the answer not in the manual?
Questions and answers