Description; General; Optional Accessories; Controls - Fohhn Easy Port Series User Instructions

4. Description

4.1 General

FP-22 modular
The EasyPort® FP-22 are self powered loudspeakers. A built-in 4
channel mixer with 2-band equalizer lets you connect a CD player
or similar audio source, two wired microphones, and the supplied
wireless microphone for simultaneous operation. Up to 4 built-in
radio receivers are possible.
The FP-22 is equipped with an integrated in CD-player.
The EasyPort® is also available with a pre-installed wireless re -
ceiver that provides highly reliable and excellent audio quality. A
handheld or bodypack transmitter of your choice (optional) makes
the EasyPort® a self-contained sound system for use with hardwire
or wireless microphones.
For mains independent operation, the EasyPort® features a built-in
high quality, leakproof lead gel rechargeable battery that conforms
to the strict standards of the German Association of Casualty
Insurers.
The battery features much lower self-discharge and a better
capacity/volume ratio than nickel-cadmium batteries and has no
memory effect.
Battery capacity is 7.2 Ah for the FP-22 modular.
FP-22 slave
Passive additional speaker can be connect to FP-22 modular with
loadspeaker cable (no integrated electronics).

4.2 Optional Accessories

FP-22 modular and FP-22 slave
• Padded carrying bag for FP-22
• Raincover for FP-22
• SHP-2 stand adapter for FP-22
• WHP-2 wall bracket for FP-22
• WHP-1 wall bracket for FP-22
• Loudspeakerstand
• Microphone stand with boom
• Carrying bag for two stands
• Music-Tray for portable music-playing equipment +
microphone, easy to mount to speaker stands
provits and tilts
,
speaker removable
,

4.3 Controls

(Refer to illustrations on page 30 to 31)
Most controls on the FP-22 are located on the back of the speaker.
The squelch control (10) and the channel selector switch (11) for
the radio receiver, which is fitted as an option, are located under
the flap in the cover.
A sturdy carrying handle is integrated in the rear panel of the
enclosure.
(1) recharge battery
Input jack for charging the integrated battery or operating the
EasyPort® on AC power.
(18) fuse
The power fuse is located below the power input socket. Prior
to replacing the power fuse unplug the FP-22 from power. Make
sure to use replacement fuse of the same type as the original
fuse only for 230 VAC:
1 A MTR (5x20mm)
(2) Power pack charge status display
Quick-charge mode, charging time 6 hours
If the yellow LED lights up continuously, the FP-22 is in quick-
charge mode, the LED then flashes once the power pack starts
charging.
(3) power switch
Switches power to the EasyPort® FP-22 audio section and
amplifier on and off but does not affect the charging circuit.
(4) Status display
Status LED, multi-coloured, charge status of the power pack is
indicated by a flashing sequence.
When the FP-22 is switched on, the LED lights up green if the
power pack is fully charged.
When the power pack falls below 30% capacity, the LED starts
to flash red.
If the power pack voltage is decreasing, the LED flashes red
increasingly quickly until it lights up red continuously.
After the LED is lit for 10 seconds, the FP-22 switches off to
prevent the power pack from an exhaustive discharge.
A signal sounds when the FP-22 switches off.
(20) DC out jack (12 volt output)
DC out jack, 12V 500mA for connecting external equipment
such as radio receivers and playback devices such as CD
players, etc.
The DC out jack is short-circuit proof and has a polarity
inversion protector.
Note:
The FP-22 modular cannot be charged via this jack.
FP-22 | 19