Page 1
IC:23451-T8210 Quick Start Guide Battery-Powered Video Doorbell (Add-on Unit) Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners.
Page 2
TABLE OF CONTENTS What’s Included Mounting The Bracket Product Overview Mounting The Doorbell How The System Works Detaching The Doorbell Verifying Your Homebase Charging The Doorbell Adding The Doorbell To Your Existing System Powering The Doorbell With Existing Doorbell Wires Determining The Power Option Notice Finding A Mounting Spot...
HOW THE SYSTEM WORKS STEP 1 VERIFYING YOUR HOMEBASE How the System Works Verify Your HomeBase The video doorbell system includes 2 parts. One is the video doorbell at your door. The other is The battery video doorbell cannot work without a HomeBase or eufyCam series system. Make the HomeBase in your house.
STEP 3 DETERMINING THE POWER OPTION Option 2 - Doorbell Wire Powered 1. If you have existing and working doorbell wiring at the front door, the doorbell will be powered by the wires constantly. So you don’t need to detach and charge it after installation. Option 1 - Battery Powered 2.
Page 6
STEP 4 FINDING A MOUNTING SPOT Place the Screw Hole Positioning Card against the wall to mark the position. Find a Mounting Spot Take the video doorbell to your front door and check the live view on the App at the same time. Find a location where you can get the desired field of view.
STEP 5 MOUNTING THE BRACKET Mount the Doorbell on Surfaces Made Out of Hard Materials 1. If you’re mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco, drill 2 holes through the Screw Hole Positioning Card with a 15/64”(6mm) drill bit. Mount the Doorbell on a Wooden Surface 2.
Page 8
STEP 6 MOUNTING THE DOORBELL Mount the Doorbell Align the doorbell on top and then snap it on the bottom. Press it down until it clicks into place. Wall Mounting Mounting Wall Mounting Wedge Bracket Bracket Without 15° Mounting Wedge With 15°...
APPENDIX 1 DETACHING THE DOORBELL APPENDIX 2 RECHARGING THE DOORBELL Detach the Doorbell Recharge the Doorbell What is required: Doorbell Detaching Pin Doorbell Detaching Pin Charging: Steady blue LED indication Fully charged: Off Charging time 6 hours 14 English English 15...
APPENDIX 3 POWERING THE DOORBELL What is required: Philips-Head Screwdriver WITH EXISTING DOORBELL WIRES 3.1 Verify whether the doorbell wires are working 1. Ring the existing doorbell to check if it is working. 2. Shut off power at the breaker. Turn the lights on / off in your home to make sure the Phillips-Head Screwdriver electricity in your house is properly shut off.
3.4 Mount the Bracket If you’re mounting the doorbell on a wooden surface, you don’t need to pre-drill pilot holes. Use the provided screws to secure the Mounting Bracket on the wall. The Screw Hole Positioning 15° Card indicates the position of the screw holes. 1.76m(5’9”) 1.2m (48") What is required: Power Drill, Mounting Bracket, 15°...
Page 12
If you’re mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco: ① Drill 2 holes through the Screw Hole Positioning Card with 15/64”(6mm) drill bit. ② Insert the provided anchors, and then use the provided screws to secure the Mounting Bracket on the wall.
Page 13
3.5 Connect the Doorbell Wires to the Doorbell 3.6 Mount the Doorbell on the Bracket Connect the wires to the terminals at the back of the doorbell, then tighten the terminal screws. Align the doorbell on top and then snap it on the bottom. Wire can connect to any terminal.
Declaration of Conformity FCC Statement Hereby, Anker Innovations Limited declares that this device is in compliance with the essential This device complies with Part 15 of the FCC Rules. Operation is subject to the requirements and other relevant provisions of Directive 2014/53/EU.For the declaration of following two conditions: (1) this device may not cause harmful interference, and (2) conformity, visit the Web site:https://www.eufylife.com/.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. IC RF Statement: Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements.