Keithley DAS-1800ST Series User Manual page 14

List of Figures
Figure 2-1.
Figure 2-2.
Figure 2-3.
Figure 2-4.
Figure 2-5.
Figure 2-6.
Figure 2-7.
Figure 2-8.
Figure 2-9.
Figure 2-10. Timing for SSHO Signal When Not Used
Figure 3-1.
Figure 4-1.
Figure 4-2.
Figure 4-3.
Figure 4-4.
Figure 4-5.
Figure 4-6.
Figure 4-7.
Figure 4-8.
Figure 4-9.
Figure 4-10. Daisy-Chaining STA-1800U Accessories
Figure 4-11. Daisy-Chaining EXP-1800 Expansion
Figure 4-12. Wiring a Signal Source to a
Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Block Diagram of Basic DAS-1800ST/HR
Series Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Block Diagram of DAS-1800ST-DA
Series Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Block Diagram of DAS-1802HR-DA Boards . . . . 2-4
Timing of Data Conversion Modes
for Channels 4 to 7. . . . . . . . . . . . . . . . . . . . . . . . 2-16
Enabling Conversions with a Software Trigger. . 2-19
Enabling Conversions with a Hardware Trigger . 2-19
Hardware Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
Timing Relationship between Data
from DO0 to DO3 and Latch Strobe DOSTB . . . 2-24
Timing for the TGOUT Signal . . . . . . . . . . . . . . 2-25
for SSH Hardware . . . . . . . . . . . . . . . . . . . . . . . . 2-27
Location of Base Address Switch . . . . . . . . . . . . . 3-5
Connector Layout of an STA-1800U Accessory. . 4-2
Attaching an STA-1800U Accessory
to a DAS-1800ST/HR Series Board . . . . . . . . . . . 4-2
Pin Assignments for the Main I/O Connector
of a DAS-1800ST/HR Series Board . . . . . . . . . . . 4-3
Pin Assignments for Connectors J1 and J2
of the STA-1800U . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Attaching an STP-50 to a DAS-1800ST/HR
Series Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Pin Assignments for Screw Terminals
of the STP-50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Attaching an SSH-8 to a DAS-1800ST
Series Board through an STA-1800U . . . . . . . . . . 4-6
Attaching an MB01 Backplane to a
DAS-1800ST/HR Series Board
through an STA-1800U . . . . . . . . . . . . . . . . . . . . . 4-7
Attaching MB02 Backplanes to an
STA-1800U Accessory . . . . . . . . . . . . . . . . . . . . . 4-8
with Attached MB02 Backplanes . . . . . . . . . . . . . 4-9
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
DAS-1800ST/HR Series Board
Configured for Single-Ended Inputs . . . . . . . . . . 4-13
vii