Burkert 2510 Operating Instructions Manual
As interface device socket
Hide thumbs
Also See for 2510:
- Operating instructions manual (6 pages) ,
- Operating instructions (5 pages) ,
- Operating instructions (5 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Burkert 2510
Summary of Contents for Burkert 2510
- Page 1 Type 2510, 2511 AS Interface Device Socket Operating Instructions...
-
Page 2: Table Of Contents
OPERATING INSTRUCTIONS Contents These operating instructions contain important information. Operating Instructions ..............2 ▶ Carefully read these instructions and follow the safety information. Intended use ................3 ▶ Keep the instructions and make them available to every user. Basic safety instructions .............. 3 ▶... -
Page 3: Intended Use
BASIC SAFETY INSTRUCTIONS These safety instructions do not take into account any unforeseen The cable plug type 2510/2511 is exclusively used to control DC circumstances or events that occur during installation, operation and coils with power output of ≤ 5 W without external power supply maintenance. - Page 4 NOTE! General hazardous situations. Observe the following to prevent injury: Electrostatically sensitive components / assemblies ▶ Observe the general rules of technical equipment. The device contains electronic components that are susceptible ▶ ▶ Do▶not▶use▶the▶device▶in▶an▶area▶where▶explosions▶are▶possible. to the effects of electrostatic discharging (ESD). Components are ▶...
-
Page 5: General Notes
Sales Centre Christian-Bürkert-Str. 13-17 D-74653 Ingelfingen Tel: +49 (0) 7940 - 10-91 111 Fax: +49 (0) 7940 - 10-91 448 E-mail: info@burkert.com International The contact addresses can be found on the back pages of the printed operating instructions. Also on the Internet at: http://www.burkert.com Figure 1: Cable Plug Type 2511... -
Page 6: Technical Data
Operating conditions slave electronics and a connector diagram according to DIN EN Cable Plug Type 2510 according to DIN EN 43650 - 803, Form C. 175301-803 (Form C and A). Cable Plug Type 2511 according to DIN EN 43650 - 803, Form A. - Page 7 Electrical data Connection of socket and plug Profile S-B.F.F Profile l S-B.A.E M12 socket, 4-pin PIN Assignment Supply voltage 29.5 - 31.5 V according to ASI specifi- + 24 V sensor supply cation (PELV) Sensor input 2 Max. power consumption From AS-Interface With electronics 10 mA 10 mA...
- Page 8 The nominal power of the valve does not correspond to the If there is no data traffic, the output is reset after 50 - 100 ms. rated capacity. This can be much higher. Output Inputs Profile S-B.F.F Profile l S-B.A.E Profile S-B.F.F Profile l S-B.A.E Max.
- Page 9 LED display for device status Programming data I/O configuration B hex (1 output, 2 inputs) ID code F hex (for assignment see below) Default address Profile Assignment of the data bits IN 1 IN 2 Fastening screw M12 connector, AS-Interface connection Figure 3: LED display for device status Item LED Colour On...
-
Page 10: Installation
INSTALLATION WARNING! Risk of injury due to improper installation ▶ Only trained technicians may perform installation work. ▶ Only carry out installations with suitable tools. ▶ Secure the system against unintentional activation. ▶ Following installation, ensure a controlled restart. Screw Seal WARNING! Risk of short circuit if the screw connection is not tight. -
Page 11: Maintenance, Troubleshooting
MAINTENANCE, TROUBLESHOOTING Seal WARNING! Risk of injury due to improper maintenance work. ▶ Only trained technicians may perform maintenance work. ▶ Secure the system against unintentional activation. ▶ Ensure a controlled restart after maintenance is completed. Maintenance work When operated according to the instructions given in this manual, Table 2: Seal seat the appliance inlet functions without maintenance. -
Page 12: Disassembly
DISASSEMBLY NOTE! DANGER! Damage in transit due to inadequately protected devices. ▶ Protect the device against moisture and dirt in shock-resistant Risk of injury from electric shock. packaging during transportation. ▶ Switch off the power supply before working on the device or ▶... - Page 13 Bürkert▶Fluid▶Control▶Systems▶ Sales▶Center▶ Christian-Bürkert-Str.▶13–17▶ D-74653▶Ingelfingen,▶Germany▶ Tel:▶+49▶(0)▶7940▶-▶10▶91▶111▶ Fax:▶+49▶(0)▶7940▶-▶10▶91▶448▶ E-mail:▶info@burkert.com International address www.burkert.com Manuals▶and▶data▶sheets▶on▶the▶Internet:▶www.burkert.com▶ Bedienungsanleitungen▶und▶Datenblätter▶im▶Internet:▶www.buerkert.de▶ Manuels▶d'utilisation▶et▶fiches▶techniques▶sur▶Internet▶:▶www.burkert.fr © Bürkert Werke GmbH & Co. KG, 2021 Operating Instructions 2102/16_EU-en_00801799 / Original DE www.burkert.com...
Need help?
Do you have a question about the 2510 and is the answer not in the manual?
Questions and answers