Related Manuals for MSA V-TEC io1 Smart Hook PFL
Summary of Contents for MSA V-TEC io1 Smart Hook PFL
- Page 1 User Instructions V-TEC io1 Smart Hook PFL Fall Protection Order No.: 10215637_r0 Print Spec: CR: 8000000XXXX MSA safety .com...
- Page 2 The warranties made by MSA with respect to the product are voided if the product is not installed and used in accordance with the instructions in this manual. Please protect yourself and your employees by following the instructions.
-
Page 3: Table Of Contents
Contents Safety Regulations Correct Use Warnings Description Physical Contents Specifications Physical Specifications Electrical Specifications Installation Installing the V-TEC io1 Operation Using the V-TEC io1 System Status Indicators Inspection Troubleshooting Warranty V-TEC io1 Smart Hook PFL... -
Page 4: Safety Regulations
Use in other applications including, but not limited to, material handling, recreational or sports related activities, or other activities not described in these user instructions, are not approved by MSA and could result in serious injury or death. Failure to follow this warning can result in serious personal injury or death. - Page 5 Ensure the V-TEC PFL is attached to a compatible anchor – flexible anchors, such as anchor lines or cantilever structures can affect the ability of the V-TEC PFL to lock-on in the case of a fall. For further clarification, contact MSA .
-
Page 6: Description
Part Number V-TEC io1 Smart Hook PFL Charging Line Components includes battery, wires, connector/adapter, cable ties, peel and stick cable tie mounts Carabiner RFID Tag/Screws V-TEC PFL User Instructions 63011-96EN-03 V-TEC io1 Smart Hook PFL User Instructions 10215637 V-TEC io1 Smart Hook PFL... -
Page 7: Specifications
USB-A / 1A and 2.1A Inputs: USB Micro Weight: 8.2 oz Dimensions: 5.16 x 2.76 x 0.59 inches 15' USB Cable Interface: USB 3.0/3.1 Gen 1 (5 Gb/s) Connector 1: USB Type-C Male Connector 2: USB Type-A Male V-TEC io1 Smart Hook PFL... - Page 8 USB C 5V Hook Battery Capacity: 350mAh LiPo/nom. 3.7V Charge Current: 350mA (1C Charging) Charge Threshold: 35mA For PFL, Rescue, Training, and Inspection content related to the lanyard itself please reference included PFL manual, MSA P/N 63011-98EN V-TEC io1 Smart Hook PFL...
-
Page 9: Installation
Locate a place for the charging line holder on one of the overhead vertical slats that allows the applicable>> charging line to hang freely. WARNING! Hook must hang freely Failure to follow this warning can result in serious personal injury or death. V-TEC io1 Smart Hook PFL... - Page 10 (18) Reconnect the PIT electrical system to the battery. <<image if applicable>> NOTE: Be sure power reaches the power pack by looking for the charging lights on the pack. <<image if (19) Replace the access panel(s) over the control area. applicable>> V-TEC io1 Smart Hook PFL...
-
Page 11: Operation
If after several tries the smart device on the snaphook is still red when the attached to the D-ring, use a paperclip to reset the device as shown, or contact MSA Customer Service . NOTE: While the snaphook and D-ring are connected the smart device will pulse green in X second intervals. -
Page 12: Inspection
Inspect labels to ensure they are present and all information is legible. The labels should be free from abrasions or peeling. See MSA V-TEC PFL Manual, MSA P/N 63011-98EN (included in box) for Retractable Lanyard portion. V-TEC io1 Smart Hook PFL... -
Page 13: Troubleshooting
If the V-TEC io1 is not working, perform a hard reset. See Table 1 for status indicators. Press the reset button on the side of the Smart Hook plastic housing with a small paperclip to turn it off. Do this again to turn the Smart Hook back on. V-TEC io1 Smart Hook PFL... -
Page 14: Warranty
Exclusive Remedy – It is expressly agreed that the Purchaser’s sole and exclusive remedy for breach of the above warranty, for any tortious conduct of MSA, or for any other cause of action, shall be the repair and/or replacement, at MSA’s option, of any equipment or parts thereof, that after examination by MSA are proven to be defective.