Summary of Contents for Walther Systemtechnik SMS-17
Page 1
Article number: SMS-17-0.3 SMS-17-0.5 SMS-17-1.0 Figure: Handpen SMS-17 (without suspension bracket) NOTE Please read the Assembly Instructions carefully before first using the incomplete device and strictly adhere to the instructions! The incomplete device may only be worked with and worked on by persons who are familiar with the assembly instructions and the current regulations for industrial safety and accident prevention.
PRAY MAGE YPE OF DEFECT APPENDIX ................................ 14 10.1 SMS-17 ........................... 14 PARE PARTS DRAWING 10.1.1 Spare parts list SMS-17 ......................... 15 10.2 ............... 16 RTICLE NUMBERS FOR AIR CAPS FLAT SPRAY NOZZLES AND NOZZLE NEEDLES 10.3 ............................16 ARTS Walther Systemtechnik GmbH –...
GmbH has a guarantee of 12 months under normal European operating conditions on its own parts (spare parts are excluded); or according to the conditions of the manufacturer. This guarantee can only be granted by Walther Systemtechnik GmbH, if: ...
The supply of atomizing air, control air, and material takes place via two hoses. The SMS-17 Handpen is a high-precision tool. Always keep clean and observe minimum instructions to maintain a long life of the valve.
4 mm PU hose. 4.4 Type label The type designation is etched in on the valve body. The serial number is also inscribed in this area. Walther Systemtechnik GmbH – D 76726 Germersheim Telefon: +49 (0)7274-7022-0 Telefax: +49 (0)7274-7022-91 http://www.walther-2000.de – info@walther-2000.de...
It is harmless to leave fluid in the valve during longer standstills if system stays under pressure (no connection to outside air). Walther Systemtechnik GmbH – D 76726 Germersheim Telefon: +49 (0)7274-7022-0 Telefax: +49 (0)7274-7022-91 http://www.walther-2000.de – info@walther-2000.de...
Accident prevention directions will be strictly followed when applying high material pressures. Please strictly follow the following instructions when planning and constructing application systems! Walther Systemtechnik GmbH – D 76726 Germersheim Telefon: +49 (0)7274-7022-0 Telefax: +49 (0)7274-7022-91 http://www.walther-2000.de – info@walther-2000.de...
Please observe the following procedure when finally shutting down the device: Clean handpene with special dilution. NOTE Please refer to the maintenance notes! Walther Systemtechnik GmbH – D 76726 Germersheim Telefon: +49 (0)7274-7022-0 Telefax: +49 (0)7274-7022-91 http://www.walther-2000.de – info@walther-2000.de...
Before opening the spray valve it must be disconnected from the air and fluid supply. Otherwise, ejected components can cause injuries The SMS-17 Handpens are high precision tools. Always keep clean and observe minimum instructions to maintain a long life of the valve. We recommend lubricating moveable parts regularly and greasing threads, especially the nozzle threads, when replacing or cleaning the nozzle.
9 Troubleshooting 9.1 General information IMPORTANT First check all supply lines for connectivity and serviceability In case of serious problems that cannot be resolved, please contact the Walther Systemtechnik GmbH customer service. 9.2 Malfunctions: Fault Possible Cause Action...
Material too thick Dilute material Increase Too little material material supply Split spray image Pressure flat jet too Increase pressure high for round jet Walther Systemtechnik GmbH – D 76726 Germersheim Telefon: +49 (0)7274-7022-0 Telefax: +49 (0)7274-7022-91 http://www.walther-2000.de – info@walther-2000.de...
Cylindrical pin DIN 6325 2 x12 97190032 Lever, 7 x 4 x 62 mm, nickel-plated 97511393 Main body SMS-17 / SV, ø20 x 100 mm, anodized Needle seal, Teflon®, 5.7 x 5 mm 97640062 97810002 Needle gland nut M7 x 0.75 x 3.5 mm 97640036 O-ring 4,7 x 1.42 / Viton®...