Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Advertisement
Table of Contents
Related Manuals for 3M SCP716W
Summary of Contents for 3M SCP716W
- Page 1 SCP700 Series Mobile Stand ™ Assembly/Installation Guide Model 78-6969-9999-0 3M Mobile Interactive Solutions Division 3M Austin Center Austin, TX 78726-9000 Phone: (800) 328-1371 www.mmm.com/meetings 9532-999-013-03 78-6971-1445-8 Rev. C...
-
Page 2: Table Of Contents
Assemble the Arm Extension ... 18 Safety Pin Installation ... 19 Technical Specification ... 20 The 3M logo and 3M are trademarks of the 3M Company. Other trademarks used herein are the properties of their respective owners. Table of Contents... -
Page 3: Important Notice
Product. All replaced parts or products become property of 3M. If the product is repaired, 3M will repair the defective part(s) with a new or used part(s). If the 3M Product is replaced, 3M will replace the 3M Product with the same or equivalent model and with a new or refurbished 3M Product. -
Page 4: Safety Information
Use in any other application has not been evaluated by 3M and may lead to an unsafe condition. It is expected that all users be fully trained in the safe operation of this stand. Use of replacement parts, or installation instructions other than described in this manual has not been evaluated by 3M and may lead to an unsafe condition. - Page 5 Always provide proper adult supervision when using the mobile stand around children. Do not climb on, hang on, or place any added weight on the mobile stand other than the 3M approved projector mounts and applicable 3M approved projectors and white boards.
-
Page 6: Parts List
Shelf Pole (Qty 1) [Optional] Set Screw Shelf (Qty 1) - Optional (Qty 1) - Optional Brass Washer (Qty 1) - Optional Caster Wrench #2 Phillips Head Screwdriver (Supplied) (Not Supplied) © 3M 2010. All Rights Reserved. Set Screws (Qty 2) - Optional... -
Page 7: Preface
3M™ SCP700 Series Mobile Stand Preface We are delighted that you have chosen a product from 3M, the 3M SCP700 Series Mobile Stand. These installation instructions will direct you in how to assemble and utilize your 3M SCP700 Series Mobile Stand. -
Page 8: Caster Wheel Installation
Threaded Tip Mounting Point 3M™ SCP700 Series Mobile Stand ground. mounting point for the caster wheels. mounting point and tighten with the supplied wrench. tightened, turn the base back over. remainder of the installation. © 3M 2010. All Rights Reserved. -
Page 9: Shelf Assembly (Optional)
© 3M 2010. All Rights Reserved. Step 1. Unpack the shelf items from the packaging. Step 2. Slide one (1) brass washer down the length Shelf Step 3. -
Page 10: Support Pole Installation
B=Model SCP712, C=Model SCP715/717/740. 3M™ SCP700 Series Mobile Stand Support Poles Base M5 Allen Wrench Support Poles Gas Shock Base Gas Shock Back Plate © 3M 2010. All Rights Reserved. M10 x 35mm Set Screw M10 x 35mm Set Screw Figure A 715/717/740... -
Page 11: Upper And Lower Horizontal Support Arm Installation
3M™ SCP700 Series Mobile Stand Upper and Lower Horizontal Support Arm Installation © 3M 2010. All Rights Reserved. Step 1. Position Upper Hanger Arm against back Back Plate support assembly. Mounting Points Step 2. Using 4 screws M6 x 10mm, align... -
Page 12: Install Mobile Cart Stabilizer
Assembly and Installation Guide Install Center Stabilizer Legs Installation Instructions: 9533-021-E03-00 Visit 3M web site at http://www.mmm.com.com/meetings Step 1 Thread each leveling foot completely into the underside of the leg. Step 2 The mobile cart must be assembled prior to attaching the stabilizer legs. -
Page 13: Attach Hanger To Projection Board
Lock Lever Unlocked Locked Step 5. Tighten top left/right bracket screws. © 3M 2010. All Rights Reserved. Step 2. Tighten bracket lock screw. Step 4. Using two people, hang projection board on horizontal support arms. Step 6. Tighten bottom left/right bracket rub foot screws. -
Page 14: Projector Installation
5 - Mounting Screws M5 x 35mm (back plate) Step 3. Swing the arm up until it locks in place. 3M™ SCP700 Series Mobile Stand Keyhole Slot Folding Wall Mount Back Plate Leveling Screw BackPlate © 3M 2010. All Rights Reserved. -
Page 15: Route Control Cable
Step 4. Using a Phillips (+) screwdriver, remove the three screws holding the cover to the base. Route Control Cable Required with optional 3M I/O Module. 6” (150mm) Step 1. Feed the control cable through the arm. Secure about 6 inches (150 mm) from the end of the existing cable bundle using a cable tie. -
Page 16: Route Cables In Stand
Step 2. Connect the power and audio cables to the connections inside the cover. Step 4. Attach the cover to the base. To reduce the risk of hazardous voltage: Do not stuff excess cables under the wall mount cover. © 3M 2010. All Rights Reserved. -
Page 17: Attach The Projector
Step 3. Using two screws and the thumbscrew, attach the mounting bracket to the end of the arm extension as shown. © 3M 2010. All Rights Reserved. Assembly and Installation Guide Step 2. Remove the three covers from the mounting screw holes. -
Page 18: Assemble The Arm Extension
Step 3. Install the 2 screws into the arm retainer. 3M™ SCP700 Series Mobile Stand Step 2. Insert the arm extension into the arm as shown. Step 4. Pull the cable bundle through the hole at the end of the arm extension. © 3M 2010. All Rights Reserved. -
Page 19: Safety Pin Installation
SCP700 Series Mobile Stand. Lanyard Projector Base Safety Tab Safety Pin © 3M 2010. All Rights Reserved. The optional I/O module attaches to back of stand using M3 x 16 mm screws. See page 11. -
Page 20: Technical Specification
Assembly and Installation Guide Technical Specification All measurements are in inches [mm]. 31.68 53.73 1365 95.65 2429 51.00 1295 3M™ SCP700 Series Mobile Stand 31.50 95.64 2429 35.50 7.39 © 3M 2010. All Rights Reserved. - Page 21 3M™ SCP700 Series Mobile Stand Assembly and Installation Guide Intentionally blank © 3M 2010. All Rights Reserved.
- Page 22 meetings@mmm.com...