Honeywell Chronotherm CM67 Manual

Installer Set-Up Mode - Settings Table
Installer Set-Up Factory Setting
Parameters
Number /
Abbreviation
(Press + or -
key to change)
Display Description
Optimisation 1:0P 0 Optimisation disabled
Minimum ON Time 2:0t 1 1 minute minimum ON time
AM-PM / 24hr Display 3:Cl 0 24 hr clock display
4:At 0 No accessory module
Accessory Module Type
plugged in
5:rP 1 Time / Temperature profile
RESET Time / Temperature
Program set to factory default
Changes to 0 when one of the
time/temp profiles are changed
You must now press the PROG 2 key to enter the next section
Heat / Cool Operation 6:HC 1 Heating Operation
7:Eh 0 Applications < 3A
Electric Heat
Pump Exercise 8:PE 0 Pump Exercise Disabled
Cycle Rate 9:Cr 6 6 cycles per hour (cph) for
gas boilers, zone valves and
fan-coil
Second Temperature 10:SS 0 No sensor fitted
Sensor
Upper Temperature Limit 11:UL 30 30°C Upper Temp. Limit
Lower Temperature Limit 12:LL 5 5°C Lower Temp. Limit
Temperature Offset 13:tO 0 No offset
Pressure Offset 14:PO 0 No offset
(needed for Weatherstation
accessory only)
Proportional Band Width 15:Pb 1.5 1.5°C Proportional Band
Return all Set-Up Features 16:FS 1 All settings held are the
factory defaults. Changes to
to Factory Settings
0 when one of the parameter
values are changed
Notes
1) When the Installer Set-Up Mode is initiated, only Category 1 (
are accessible.
Category 2 ( 2) Set-Up Features are accessed by pressing the PROG. 2 key.
2) Remember to always press the INFO button to confirm that you want to store your new
Installer Set-Up setting.
3) To exit the Installer Set-Up Mode move the slider to the AUTOmatic or MANual position.
Home Comfort & Systems
Honeywell Control Systems Ltd.
Newhouse Industrial Estate
Motherwell, ML1 5SB
Scotland
Optional Setting Installer Set-Up
Category
(Press keys PROG 1
or 2 to select)
1 2
Display/Setting Description
1 Optimisation enabled 1
2 to 5 2 - 2 minutes 1
3 - 3 minutes
4 - 4 minutes
5 - 5 minutes
1 12 hr AM / PM clock display 1
1, 2 1 - Auto Time Setting Module 1
2 - Weatherstation Module
0 Time / Temperature are as 1
programmed
1 To restore the factory profile
set to 1
0 Cooling Operation 2
1 Applications 3 - 8A 2
1 Pump Exercise Enabled 2
3, 9, 12 3 - 3 cph 2
9 - 9cph
12 - 12 cph
1, 2 1 - Outside Temperature 2
Sensor fitted
2 -Remote Temp. Sensor fitted
21 to 29 21°C to 29°C adjustment in 2
1°C steps
6 to 16 6°C to 16°C adjustment in 1°C 2
steps
-3 to +3 -3°C to +3°C adjustment in 2
0.1°C steps
-99 to +99 -99 mbar to +99 mbar 2
adjustment in 1 mbar steps
1.6 to 3.0 1.6°C to 3.0°C adjustment in 2
0.1°C steps
0 Settings are as modified 2
above
To restore the factory profile
1 set to 1
1) Set-Up Features
This product has been designed with your
environment in mind! Please respect this by
disposing of all packaging, used parts and
eventually the product itself in an environ-
mentally friendly manner.
honeywell
http://europe.hbc.honeywell.com
1
3 4 a
4 c
6
honeywell
Chronotherm
Installation
2
4 b
3mm
3mm
max.
max.
5
1.0-2.5mm²
42009636-005 R3