Summary of Contents for OPTIMUM Maschinen OPTIgrind GBS 75
Page 1
Safety Operating manual Technical specification Version 1.0.1 Delivery, interdepartmental transport, assembly and commissioning Operation Maintenance Belt grinder Appendix Part no. Ersatzteile - Spare parts 3321155 3321160 GBS 150 GBS 75...
Page 2
If you have any further questions after reading these operating instructions and you are not able to solve your problem with a help of these operating instructions, please contact your special- ised dealer or directly the company OPTIMUM. Optimum Maschinen Germany GmbH Dr.- Robert - Pfleger - Str. 26 D-96103 Hallstadt...
Page 3
Safety Glossary of symbols provides further instructions calls on you to act listings This part of the operating instructions explains the meaning and use of the warning notes included in these operating instructions, defines the intended use of the belt grinder, ...
If the belt grinder is used in any way other than described above, modified without authoriza- tion of Optimum Maschinen Germany GmbH, then the belt grinder is being used improperly. We will not be held liable for any damages resulting from any operation which is not in accord- ance with the intended use.
We expressly point out that the guarantee will expire, if any constructive, technical or proce- dural changes are not performed by the company Optimum Maschinen Germany GmbH. WARNING! Risk of injury caused by flying workpieces. Injuries caused by sharp-edged workpieces.
Page 6
and strictly follow these operating instructions. Always disconnect the belt grinder from the electrical power supply before performing cleaning or maintenance tasks. CAUTION! The belt grinder may only be operated with the support plate clamped. Operation with a dismantled or unclamped plate can lead to dangerous conditions for the operator. Make sure that the gap between the support plate of the workpiece and the belt grinder is as small as possible.
be duly qualified, and strictly follow these operating instructions. In the event of improper use there may be a risk to personnel, the grinding machine and other property and the functionality of the belt grinder may be compromised. User positions The operator position is in front of the belt grinder or next to the belt grinder.
Disconnecting and securing the belt grinder Disconnect the mains plug before starting maintenance and repairs. 1.10 Emissions The noise emission of the belt grinder is in the range of 82 to 85 dB(A). If the belt grinder is installed in an area where various machines are in operation, the noise exposure (immission) on the operator of the belt grinder at the working place may exceed 85 dB(A).
Page 9
Delivery, interdepartmental transport, assembly and commissioning Notes on transport, installation, commissioning Improper transport, installation and commissioning is liable to accidents and can cause damage or malfunctions to the machine for which we do not assume any liability or guarantee. Transport the scope of delivery secured against shifting or tilting with a sufficiently dimen- sioned industrial truck or a crane to the installation site.
Store packed and unpacked parts only under the intended environmental conditions. Follow the instructions and information on the transport box. Consult Optimum Maschinen Germany GmbH if the machine and accessories are stored for more than three months or are stored under different environmental conditions than those spec- ified here.
Page 11
The GU2 from Optimum Maschinen Germany GmbH is the ideal extraction unit. This suction device has 60mm suction hoses, where both suction connections of the belt grinder can be connected at the same time.
Page 12
Dimensions 3.6.1 GBS 75 1070 Center of gravity GBS75 | GBS150 Delivery, interdepartmental transport, assembly and commissioning Translation of original instruction Version 1.0.1 - 2020-10-14...
Page 13
Dimensions 3.7.1 GBS 150 1070 Center of gravity Delivery, interdepartmental transport, assembly and commissioning GBS75 | GBS150 Version 1.0.1 - 2020-10-14 Translation of original instruction...
First commissioning ATTENTION! Before commissioning the machine, all bolts, fastenings and protections must be checked and retightened as necessary! CAUTION! Danger from the use of unsuitable sanding belts. Only use abrasive belts with the correct width and length. WARNING! First commissioned of the belt grinder by inexperienced personnel constitute a risk to personnel and equipment.
Switching on the machine CAUTION! Only press the emergency-stop button in a genuine emergency. You may not use the emergency stop button to stop the machine during normal operation. The service life of the emergency stop switch is not designed to stop the machine during normal operation. 4.2.1 Switching on ...
Surface grinding Open the lid at the top and fold it back. Place the workpiece on top of the sanding belt, place it against the counter stop and press it down. Contact rollers grinding Place the workpiece on the workpiece support and by rocking grind and/or deburr the work- piece.
Page 17
Turn the tension lever (3) out to release the tension of the sanding belt. Lift the sanding belt (4) off the rollers and insert a new sanding belt. Operation GBS75 | GBS150 Version 1.0.1 - 2020-10-14 Translation of original instruction...
Repair Optimum Maschinen Germany GmbH accepts no liability nor does it guarantee against damage and operating malfunctions resulting from failure to observe these operating instructions. Use only perfect and suitable tools, only original spare parts or serial parts expressly approved by Optimum Maschinen Germany GmbH for repairs.
Neither are the following items covered by liability or warranty claims: - Wearing parts and components which are subject to normal and intended wear, such as V-belts, ball bearings, lighting, filters, seals, etc. - Non reproducible software errors Any services, which OPTIMUM GmbH or one of its agents performs in order to fulfil any additional warranty are neither an acceptance of the defects nor an acceptance of its obli- gation to compensate.
6.3.3 Disposal of electrical and electronic components Please make sure that the electrical components are disposed of professionally and according to the statutory provisions. The device is composed of electrical and electronic components and must not be disposed of as household waste. According to the European Directive regarding electrical and electronic used devices and the implementation of national legislation, used power tools and electrical machines need to be collected separately and supplied to an environmentally friendly recycling centre.
EC Declaration of Conformity Machinery Directive 2006/42/EC Annex II 1.A The manufacturer / Optimum Maschinen Germany GmbH retailer: Dr.-Robert-Pfleger-Str. 26 D - 96103 Hallstadt hereby declares that the following product, Product designation: Belt grinder Designation of the machine: GBS 75...
Ersatzteile - Spare parts Ersatzteilbestellung - Ordering spare parts Bitte geben Sie folgendes an - Please indicate the following : Seriennummer - Serial No. Maschinenbezeichnung - Machines name Herstellungsdatum - Date of manufacture Artikelnummer - Article no. Die Artikelnummer befindet sich in der Ersatzteilliste.
Page 23
GBS75 | GBS150 GBS75 | GBS150 DE | EN Version 1.0.1 - 2020-10-14 Originalbetriebsanleitung...