Operation - EINHELL RT-SM 330 U Operating Instructions Manual

Anleitung_RT_SM_330_U_SPK1:_
GB
lever (3) latches into place.
The clamping device (8) can be fitted on the left
or right of the fixed saw table (18).
Undo the locking screws for the workpiece
support (30).
Guide the limit stop (9) over a holding bar (10)
and install it on the fixed saw table (18),
tightening the appropriate locking screw (30).
Mount the second holding bar (10) on the
opposite side of the saw and secure with the
appropriate locking screw (30).
When the locking screw (22) is loosened, you can
tilt the machine head (4) to the left by up to 45°.
If the machine is used without the base frame the
tipping guard (26) must be pulled out. This
prevents it tipping over to the rear.
6.3 Assemble the base frame and bolt the saw to
the base frame (Fig. 5-10)
First screw the 2 short upper angle brackets (E)
(Please note: The upper angle brackets have oval
holes (for fastening the saw), first bolt them
loosely from the inside to the top of the feet (A).
Then screw the 2 longer upper angle brackets (C)
to the feet from the outside so that the oval holes
coincide with the mounting holes on the saw.
Place the base frame on the 4 feet (A) and
loosely screw the 2 long (B) and 2 short (D) struts
to the 4 feet.
Align the base frame and tighten all the screws.
Place the saw on the base frame so that the 4
oval holes on the base frame coincide with the
mounting holes on the saw.
Secure all 4 bolts on the base frame so that they
are tight.
6.4 Fitting the dust extraction device (Fig. 13-19)
Mount the dust extraction nozzle (38) in the outlet
opening under the cutting arm.
Mount the big end of the angle piece (35) on the
back of the crosscut and miter saw at the outlet
opening. The angle piece has to point to the side
or down.
On the angle piece you can either attach the dust
bag (23) or a suction hose for drawing off the saw
dust.
Mount the second angle piece on the upper dust
extraction socket (35) and plug on the suction
hose (32).
With the Y-piece (34) you can join together the
upper and lower suction hose. Plug the hose with
adaptor (37) on the outlet of the Y-piece. You can
now connect a suitable dust extractor to the
adaptor.
20
12.01.2009 17:11 Uhr Seite 20
6.5 Final adjustment of the stop for crosscut 90°
(Fig. 1-2, 20-22)
Fasten the turntable (17) in 0° position.
Undo the securing screw (22) and tilt the machine
head (4) as far to the right as possible using the
handle (1).
Place the 90° angular stop (a) between the saw
blade (7) and the turntable (17).
Retighten the counter nut (c) to secure this
setting.
Finally check the position of the pointer (20) on
the scale (19). If necessary undo the pointer (20)
with a Philips screwdriver, set it to the 0° position
on the scale (19) and tighten the retaining screw
again.
An angular stop is not supplied.
6.6 Final adjustment of the stop for meter cut 45°
(Fig. 1-2, 23)
Fasten the turntable (17) in 0° position.
Undo the securing screw (22) and tilt the machine
head (4) to the right to an angle of 45° using the
handle (1).
Place the 45° stop angle (f) between the blade (7)
and the turntable (17).
Undo the counter nut (e) and adjust the
adjustment screw (f) until the angle between the
saw blade (7) and the turntable (17) is 90°.
An angular stop is not supplied.

7. Operation

7.1 Crosscut 90° and turntable 0° (Fig. 1 – 3, 24)
For cutting widths up to 100 mm it is possible to fix
the saw's drag function in its rear position with the
fixing screw for drag guide (25). If the cutting width
exceeds 100 mm you must ensure that the fixing
screw for the drag guide (25) is undone and that the
machine head (4) can be moved.
Move the machine head (4) to its upper position.
Use the handle (1) to push back the machine
head (4) and fix it in this position if required
(dependent on the cutting width).
Place the piece of wood to be cut at the stop rail
(11) and on the turntable (17).
Lock the material with the clamping device (8) on
the fixed saw bench (18) to prevent the material
from moving during the cutting operation.
Push down the release lever (3) to release the
machine head (4).
Press the ON/OFF switch (2) to start the motor.
If the drag guide (24) is fixed: Move the machine
head (4) downwards evenly and with gentle
pressure using the handle (1) until the saw blade
(7) has cut through the workpiece.