Honeywell 7800 Series Product Data page 20

7800 SERIES S7800B DISPLAY MODULE
Table 4. Fault Message and Recommended Troubleshooting (continued) .
Fault Code
Fault 110 The configuration jumpers
Internal Fault differ from stored values.
Fault 111 Relay Module configuration
Internal Fault jumper test failure.
Fault 112 Relay Module self-test
Internal Fault failure.
Fault 113 Relay Module self-test
Internal Fault failure.
Fault 114 Relay Module self-test
Internal Fault failure.
Fault 117 Relay Module self-test
Internal Fault failure.
Fault 118 Relay Module self-test
Internal Fault failure.
Fault 119 Relay Module self-test
Internal Fault failure.
Fault 120 Relay Module self-test
Internal Fault failure.
Fault 121 Relay Module self-test
Internal Fault failure.
Fault 122 Relay Module self-test
Internal Fault failure.
Fault 123 Relay Module self-test
Internal Fault failure.
Fault 125 Relay Module self-test
Internal Fault failure.
Fault 126 Relay Module self-test
Internal Fault failure.
Fault 127 Safety relay feedback
Internal Fault circuit was in an improper
state.
Home and Building Control
Honeywell Inc.
Honeywell Plaza
P.O. Box 524
Minneapolis MN 55408-0524
Honeywell Latin American Region
480 Sawgrass Corporate Parkway
Suite 200
Sunrise FL 33325
65-0219—1 G.R. Rev. 12-97
65-0219—1
System Failure
1. Inspect the jumper connections. Assure that they match the original
selection and that clipped jumpers have been completely removed.
2. Reset and sequence the 7800.
3. If fault persists, replace the relay module.
4. Configuration jumpers must be selected prior to 200 hours of
operation. If configuration jumpers are changed after 200 hours of
operation, lockout 110 will occur.
1. Inspect the jumper connections. Assure that they match the original
selection and that clipped jumpers have been completely removed.
2. Reset and sequence the 7800.
3. If fault persists, replace the relay module.
1. Reset and sequence the 7800.
2. If fault persists, replace the relay module.
1. Reset and sequence the 7800.
2. If fault persists, replace the relay module.
1. Reset and sequence the 7800.
2. If fault persists, replace the relay module.
1. Reset and sequence the 7800.
2. If fault persists, replace the relay module.
1. Reset and sequence the 7800.
2. If fault persists, replace the relay module.
1. Reset and sequence the 7800.
2. If fault persists, replace the relay module.
1. Reset and sequence the 7800.
2. If fault persists, replace the relay module.
1. Reset and sequence the 7800.
2. If fault persists, replace the relay module.
1. Reset and sequence the 7800.
2. If fault persists, replace the relay module.
1. Reset and sequence the 7800.
2. If fault persists, replace the relay module.
1. Reset and sequence the 7800.
2. If fault persists, replace the relay module.
1. Reset and sequence the 7800.
2. If fault persists, replace the relay module.
1. Reset and sequence the 7800.
2. If fault persists, replace the relay module.
Home and Building Control
Honeywell Limited-Honeywell Limitée
155 Gordon Baker Road
North York, Ontario
M2H 3N7
Honeywell Europe S.A.
3 Avenue du Bourget
B-1140 Brussels
Belgium
Printed in U.S.A. on recycled
paper containing at least 10%
post-consumer paper fibers.
Recommended Troubleshooting
Honeywell Asia Pacific Inc.
Room 3213-3225
Sun Hung Kai Centre
No. 30 Harbour Road
Wanchai
Hong Kong
20 www.honeywell.com/bbc