Page 1 Satellite User’s Guide If you need assistance: Toshiba’s Support Web site pcsupport.toshiba.com Toshiba Customer Support Center Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see page 183 in this guide.
Page 2 TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA,...
Page 3 Only Peripherals complying with the FCC Class B limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's ports.
Page 4: Industry Canada Requirement
This device must accept any interference received, including interference that may cause undesired operation. Contact either: Toshiba’s Support Web site at pcsupport.toshiba.com. Or call the Toshiba Customer Support Center: Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273 Industry Canada Requirement This Class B digital apparatus complies with Canadian ICES-003.
Page 5: Telephone Company Procedures
Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba, or the Toshiba Customer Support Center within the United States at (800) 457-7777 or Outside the United States at (949) 859-4273. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
Page 6 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. Instructions for IC CS-03 Certified Equipment NOTICE: The Industry Canada label identifies certified equipment.
Page 7: Wireless Interoperability
Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: The IEEE 802.11 Standard on Wireless LANs (Revision A/B/G), as defined and approved by the Institute of Electrical and Electronics Engineers.
Page 8: Wireless Lan And Your Health
The radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Page 9 Canada – Industry Canada (IC) This device complies with RSS 210 of Industry Canada. The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population;...
Page 10 This Directive applies to EU member countries only and does not apply to end users in other countries such as the United States. Although the initial emphasis is in Europe, Toshiba is already working with design engineers, suppliers, and other partners to determine appropriate worldwide product life cycle planning and end-of-life strategies for our products.
Page 11 VCCI Class B Information Modem Warning Notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Page 12 2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment.
Page 13: Device Authorization
FH: This equipment uses FH-SS modulation. The interference range of this equipment is less than 10m. This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-15-1048 Direct Dial: 03-3457-4850...
Page 14 Approved Countries/Regions for the Intel Link 5100/5300 Series This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Andorra Austria Belgium Brazil Cambodia Chile Costa Rica...
Page 15 Qatar Russia San Marino Singapore South Africa Sweden Taiwan Ukraine Uruguay Venezuela Zimbabwe Approved Countries/Regions for the Atheros Wireless Wi-Fi Link AR5B95 Series This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Page 16 Nigeria Peru Portugal Romania Senegal Slovak Republic South Korea Sweden Thailand Ukraine Yemen Approved Countries/Regions for the Atheros Wireless Wi-Fi Link AR5B93 Series This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Page 17 Philippines Puerto Rico Russia Serbia Slovenia Sri Lanka Thailand Ukraine Yemen Approved Countries/Regions for use for the Atheros AR5BXB72 2.4 + 5GHz 11n minicard This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. NOTE This device works on passive scan only.
Page 18 Sweden UAE (United Arab Emirates) Uruguay Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ For private usage outside buildings across public grounds over less than Belgique: 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m.
Page 19 Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries European Community Countries Austria Belgium, France, Switzerland/Liechtenstein Denmark, Finland, Germany, Greece, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Sweden, UK Iceland, Spain O: allowed x: forbidden To remain in conformance with European spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply.
Page 20 Approved Countries/Regions for use for the Atheros AR5BXB63 11g minicard This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Argentina Azerbaijan Brazil Chile Costa Rica...
Page 21 Approved Countries/Regions for the Realtek This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Albania Austria Bangladesh Bosnia and Herzegovina Canada Colombia Cyprus Ecuador...
Page 22 Approved Countries/Regions for use for the ® Intel PRO/Wireless 3945ABG Network Connection This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. NOTE An adhoc mode is available in Ch1-Ch11(802.11b/g).
Page 23 11a, 11b, 11g and 11n wireless are based on IEEE 802.11a, 802.11b, 802.11g and 802.11n respectively. The IEEE 802.11n specification has not been finalized and is currently in draft release. The TOSHIBA 11a/b/g/n Wireless LAN Adapters are based on the Draft Release, Version 1.0, of the IEEE 802.11n specification.
Page 24: Bluetooth Wireless Technology Interoperability
Always use Bluetooth cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA computer product support on Web site http://www.toshiba-europe.com/computers/tnt/ bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for...
Page 25: Bluetooth Wireless Technology And Your Health
Approved Countries/Regions for use (Bluetooth technology) ® Bluetooth Card from Toshiba equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Argentina Belgium...
Page 26: Regulatory Statements
The radiated output power of the Bluetooth Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 27 Never attempt to disassemble, adjust or repair an optical drive. You could damage the drive. You would also be exposed to laser light or other safety hazards, resulting in serious injury. Always contact an authorized Toshiba service provider, if any repair or adjustment is required.
Page 28 Copyright This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
Page 29 Systems Incorporated in the United States and/or other countries. Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Toshiba is under license. Other trademarks and trade names are those of their respective owners.
Page 30: Table Of Contents
Contents Introduction... 38 This guide ...40 Safety icons ...41 Other icons used...41 Your computer’s features and specifications ...42 Other documentation ...42 Service options ...42 Chapter 1: Getting Started... 43 Selecting a place to work ...43 Setting up a work environment ...43 Keeping yourself comfortable ...44 Precautions...44 Important information on your computer’s...
Page 31 Turning on the power ...51 Setting up your software...52 Registering your computer with Toshiba ...52 Adding optional external devices...53 Adding memory (optional) ...53 Installing a memory module ...54 Removing a memory module...59 Checking total memory ...61 Recovering the Internal Storage Drive ...62 Recovering to out-of-box state (recommended recovery method)...63...
Page 32 Contents Using the Shut Down command ...84 Using and configuring Hibernation mode ...86 Using and configuring Sleep mode ...89 Closing the display panel ...92 Customizing your computer’s settings...92 Caring for your computer...92 Cleaning the computer ...92 Moving the computer...93 Using a computer lock ...93 Chapter 2: Learning the Basics...
Page 33 Setting battery notifications ...120 Conserving battery power ...121 Power Plans...122 Using a hot key to set the Power Plan...123 Using TOSHIBA eco Mode ...124 Changing the main battery ...125 Removing the battery from the computer ...125 Inserting a charged battery ...127 Taking care of your battery ...128...
Page 34 Using the Bridge Media Adapter Slot ...144 Inserting memory media...145 Removing memory media...145 Using the i.LINK Using the eSATA/USB combo port...146 Chapter 5: Utilities...147 TOSHIBA Assist ...148 Connect...149 Secure...150 Protect & Fix ...151 Optimize...152 TOSHIBA Application Installer...153 Setting passwords ...154 the Internet ...140...
Page 35 Deleting a user password...157 TOSHIBA Face Recognition Utility...158 TOSHIBA PC Diagnostic Tool Utility...159 TOSHIBA HDD Protection Utility ...160 TOSHIBA SD™ Memory Card Format Utility ...161 Mouse Utility ...162 TOSHIBA Hardware Setup...163 USB Sleep and Charge Utility ...165 Starting the USB Sleep and Charge Utility...165 USB Sleep and Charge ...165...
Page 36 Wireless networking problems...202 DVD operating problems...204 Develop good computing habits ...205 Data and system configuration backup in the If you need further assistance...211 Before you contact Toshiba ...211 Contacting Toshiba ...211 Other Toshiba Internet Web sites...212 Toshiba’s worldwide offices...212 ®...
Page 37 Appendix A: Hot Keys/TOSHIBA Cards ... 214 Hot Key Cards ...214 Using the Hot Key Cards ...215 Application Cards...216 Using the Application Cards...217 Card Case...218 Hot key functions ...218 Volume Mute ...219 Lock (Instant security) ...220 Power plan ...221 Sleep mode ...222 Hibernation mode ...223...
Page 38: Introduction
You can wake the computer from Sleep mode by pressing the power button. See the “Mobile Computing” section of the Toshiba User’s Guide for more information on using power management settings to...
Page 39 (RoHS), which restricts use of lead, cadmium, mercury, hexavalent chromium, PBB, and PBDE. Toshiba requires its computer component suppliers to meet RoHS requirements and verifies its suppliers’ commitment to meeting RoHS requirements by conducting component sampling inspections during the product design approval process.
Page 40: This Guide
Toshiba’s Web site at pcsupport.toshiba.com. While Toshiba has made every effort at the time of publication to ensure the accuracy of the information provided herein, product specifications, configurations, prices, system/component/options availability are all subject to change without notice.
Page 41: Safety Icons
Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Page 42: Your Computer's Features And Specifications
To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com. If you have a problem or need to contact Toshiba, see Goes Wrong” on page System icons 183.
Page 43: Chapter 1: Getting Started
Chapter 1 Getting Started This chapter provides tips for using your computer effectively, summarizes how to connect components, and explains what to do the first time you use your computer. The “Instruction Manual for Safety and Comfort,” that is shipped with your computer, contains important safety information.
Page 44: Keeping Yourself Comfortable
Extreme heat, cold, or humidity. Liquids and corrosive chemicals. Keeping yourself comfortable The Toshiba Instruction Manual for Safety and Comfort, included with your computer, contains helpful information for setting up your work environment and tips for working comfortably throughout the day.
Page 45 Avoid prolonged physical contact with the underside or surface of the computer. Computer base and palm rest can become hot! Avoid prolonged contact to prevent heat injury to skin. Read the “Avoid extended contact between computer base/palm rest and skin” section in the “Instruction Manual for Safety and Comfort”...
Page 46: Important Information On Your Computer's Cooling Fan
Getting Started Setting up your computer Important information on your computer’s cooling fan Your computer may have a CPU cooling fan that cools the CPU by drawing outside air into the computer. Always make sure your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Sleep mode).
Page 47: Connecting To A Power Source
TOSHIBA Battery Charger (that may have been provided with your computer), or use AC adaptors and battery chargers specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the computer possibly resulting in serious injury.
Page 48 Getting Started Connecting to a power source To connect AC power to the computer: Connect the power cord/cable to the AC adaptor. (Sample Illustration) Connecting the power cord/cable to the AC adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
Page 49: Charging The Main Battery
The computer’s main battery light gives you an indication of the main battery’s current charge: Glows amber while the main battery is being charged (AC adaptor connected) Glows white when the main battery is fully charged Is unlit when the main battery has discharged, the battery is not charging, or the AC adaptor is not plugged into the computer or AC outlet Flashes amber when the main battery charge is low and it...
Page 50: Using The Computer For The First Time
Getting Started Using the computer for the first time NOTE Battery life and charge time may vary depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel Facing the front of the computer, locate the center of the display panel.
Page 51: Turning On The Power
Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology.
Page 52: Setting Up Your Software
Product registration can be completed by either visiting the Toshiba Web site at http://www.register.toshiba.com, or by double-clicking the Toshiba Resources icon on your desktop and then double-clicking Toshiba Registration. Failure to complete Product Registration will not diminish Customer rights under the Toshiba standard limited Warranty.
Page 53: Adding Optional External Devices
Adding optional external devices NOTE Before adding external devices or memory, Toshiba recommends setting up your software. See After starting your computer for the first time you may want to: Add more memory (see page Connect a mouse (see Connect a full-size keyboard (see keyboard”...
Page 54: Installing A Memory Module
Getting Started Adding memory (optional) Installing a memory module Memory modules can be installed in the memory module slots on the base of the computer. You will need a small Phillips screwdriver for this procedure. If the computer has been running recently, the memory module(s) may be hot.
Page 55 If the computer is on, begin at step 1; otherwise, skip to step 3. Click Start, and then click the arrow next to the lock button in the lower-right corner of the Start menu. The Shut Down menu appears. Start (Sample Image) Shut Down menu Click Shut Down.
Page 56 Getting Started Adding memory (optional) Using a small Phillips screwdriver, loosen the captive screw that secures the memory module slot cover. (Sample Illustration) Removing the memory module slot cover Remove the memory module slot cover. Place the screw and the cover in a safe place so that you can retrieve them later.
Page 57 NOTE If your system has the memory modules stacked on top of one another, you must remove the top module first before removing/installing the bottom module. NOTE For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A.
Page 58 Getting Started Adding memory (optional) Once the module’s connector is fully inserted into the socket, press downward on the top edge of the module to seat the module into the latches at the sides of the socket. These latches should “snap” into place securely with the corresponding cutouts in the side of the module.
Page 59: Removing A Memory Module
Replace the memory module slot cover and secure it using the screw. Re-insert the main battery. For more information on inserting the main battery, see Turn the computer right side up. Reconnect the cables. Restart the computer. TECHNICAL NOTE: You must have at least one memory module installed for the computer to work.
Page 60 Getting Started Adding memory (optional) NOTE The following screen may appear when you turn on the power: If “Start Windows If one of the Safe Mode options is highlighted, it is best to press to go into Safe Mode, then shut down and restart the system, at Enter which time Windows When Safe Mode is suggested, this could be a sign that you may...
Page 61: Checking Total Memory
Gently lift the memory module to a 30-degree angle and slide it out of the slot. (Sample Illustration) Removing the memory module Replace the memory module slot cover and secure it using the screw. Re-insert the main battery. For more information on inserting the main battery, see Turn the computer right side up.
Page 62: Recovering The Internal Storage Drive
Getting Started Recovering the Internal Storage Drive NOTE From time to time, Windows “Windows feature to prevent programs or people from doing things on your computer without your permission. If you were trying to perform the action, click Continue; otherwise, click Cancel. If unsure, cancel and try again.
Page 63: Recovering To Out-Of-Box State (Recommended Recovery Method)
For more information on creating recovery media, see page The Toshiba Recovery Wizard also provides the option of erasing your internal storage drive, without restoring the information on the drive. See more information.
Page 64 Click Yes to continue. (Sample Image) Warning screen When the Toshiba Recovery Wizard opens and the Selecting a process screen displays, select Recovery of Factory Default Software and then click Next. (Sample Image) Selecting a Process screen...
Page 65: Recovering To A Custom Size Partition
The Recovery of Factory Default Software screen appears. Select Recover to out-of-box state. (Sample Image) Recovery of Factory Default Software screen Click Next. A confirmation message displays reminding you that all data will be lost during the recovery process. Be sure to save your work to external media before proceeding.
Page 66 Getting Started Recovering the Internal Storage Drive The “Recover to a custom size partition” option restores your C: drive to its out-of-box state, and allows you to specify the size for the C: partition. You can resize and recover the C: drive using the utilities stored on your computer’s internal storage drive or using recovery media, if you have created recovery discs.
Page 67 Recovering the Internal Storage Drive When the Toshiba Recovery Wizard opens and the Selecting a process screen displays, select Recovery of Factory Default Software and then click Next. (Sample Image) Selecting a Process screen The Recovery of Factory Default Software screen appears.
Page 68: Recovering Without Changing The Internal Storage Drive Partitions
Getting Started Recovering the Internal Storage Drive Click Next to begin the recovery. When the process is complete, a message displays indicating that the C: drive has been recovered. Press any key on the keyboard to restart the computer. Recovering without changing the internal storage drive partitions Recovering without changing the internal storage drive partitions deletes all information stored on the C: drive.
Page 69 Click Yes to continue. (Sample Image) Warning screen When the Toshiba Recovery Wizard opens and the Selecting a process screen displays, select Recovery of Factory Default Software and then click Next. (Sample Image) Selecting a Process screen...
Page 70: Creating Recovery Media
If your optical disc drive is not a writable drive, contact Toshiba Customer Support to obtain the Recovery media for your system. The Toshiba Customer Support Center in the United States is (800) 457-777; outside the United States it is (949) 859-4273.
Page 71: Restoring From Recovery Media
To create recovery DVDs: Click Start, All Programs, TOSHIBA, Recovery, and then Recovery Disc Creator. Select DVD (to create Recovery media on DVD). Select the items you want to copy to DVD by clicking the check box next to each item’s Name—recovery files, applications (original bundled drivers and applications), or both the recovery files and applications.
Page 72 A warning screen appears, stating that when the recovery is executed all data will be deleted and rewritten. Click Yes to continue. When the Toshiba Recovery Wizard opens and the Selecting a Process screen displays, select Recovery of Factory Default Software and then click Next.
Page 73: Erasing The Internal Storage Drive
“Recovering the Internal Storage Drive” on page To delete all data and partitions from the internal storage drive: Access the Toshiba Recovery Wizard on your internal storage drive or on your recovery DVDs. To access the Recovery Wizard on your internal storage drive: Press and hold the 0 (zero) key while powering on the computer.
Page 74 Getting Started Erasing the Internal Storage Drive Choose one of the following options on the Erase the hard disk screen: Delete all data and partitions from the hard disk—This option deletes all of the data on the internal storage drive without overwriting the drive.
Page 75: Checking The Internal Storage Drive Operating Status
Highlight the hard disk drive in the Volume list to display its status in the lower portion of the screen. Installing drivers and applications The Toshiba Application Installer allows you to reinstall the drivers and applications that were originally bundled with your computer. To reinstall drivers and applications: Click Start, All Programs, Toshiba, Recovery, and then TOSHIBA Application Installer.
Page 76: Scrolling With The Touchpad
Getting Started Using the TouchPad™ NOTE Because the TouchPad is much smaller than the display screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad in the preferred direction. Once you have positioned your cursor, you can click it into place by either double-tapping the TouchPad or clicking the control buttons.
Page 77: Using External Display Devices
Using external display devices Your computer comes with a built-in display, but you can also connect the following types of external display devices to the video ports described below: An HDMI™-compatible television or VCR/DVD player via the HDMI Out port An external monitor or projector via the RGB (monitor) port RGB (monitor) port (Sample Illustration) Side of system...
Page 78 HDMI™-CEC (Consumer Electronics Control) is a standard in the CE Industry which allows devices to work together over an HDMI cable. Toshiba computers with HDMI-CEC include a Toshiba utility (that may need to be installed) dedicated to take advantage of...
Page 79: Directing The Display Output When You Turn On The Computer
Directing the display output when you turn on the computer Once you have connected an external display device, you can choose to use the internal display only, the external device only, or both simultaneously. NOTE Some modes are only available with the appropriate device attached and turned on.
Page 80: Adjusting The Quality Of The External Display
Getting Started Using an external keyboard Adjusting the quality of the external display To obtain the best picture quality from your television (or other video display device), you may need to adjust the video settings. See the video device documentation for additional configuration steps.
Page 81: Setting Up A Printer
If your printer does not support Plug and Play, you can set up the printer as described in To connect a printer to your computer: Connect the printer cable to the printer and then connect the other end to one of the computer’s USB ports. Plug the printer’s power cable into a live AC outlet.
Page 82: Turning Off The Computer
Getting Started Turning off the computer Turning off the computer Pressing the power button before shutting down the Windows operating system could cause you to lose your work. Make sure the system indicator panel’s storage drive light and the drive-in-use light are off.
Page 83 Hibernation mode Hibernation mode shuts the computer down completely, but it first saves the current state of the computer to the internal storage drive. Since Hibernation mode does not require power to maintain the saved information, system settings are retained indefinitely. Factors to consider when choosing Hibernation: While in Hibernation mode, the computer uses no main battery power.
Page 84: Using The Shut Down Command
Getting Started Turning off the computer Restarting from Sleep takes less time and consumes less main battery power than restarting after turning off the computer using the Hibernation or Shut down commands. When starting up again, the computer returns to the mode in which you left it, including all open programs and files you were using.
Page 85 Turning off the computer more quickly You can also turn off the computer by pressing the power button. To use this method, you first need to activate it using the Power Options feature. By default, pressing your computer’s power button puts the computer into Sleep mode.
Page 86: Using And Configuring Hibernation Mode
Getting Started Turning off the computer Lid close action Set this option to Shut down if you want the computer to shut down when you close the display panel. Power button action Set this option to Shut down if you want the computer to shut down when you press the power button.
Page 87 Click Hibernate. The computer saves the state of all open programs and files, turns off the display, and then turns off. Configuring Hibernation mode options You can place the computer into Hibernation mode by either pressing the power button or closing the display panel. You can also specify an amount of time after which the computer automatically goes into Hibernation mode.
Page 88 Getting Started Turning off the computer Select Hibernate for the options you want. NOTE These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power. Lid close action Set this option to Hibernate if you want the computer to go into Hibernation mode when you close the display panel.
Page 89: Using And Configuring Sleep Mode
Using and configuring Sleep mode To turn off the computer using the Sleep command: Click Start, and then click the arrow next to the Lock button in the lower-right part of the Start menu. The Shut Down menu appears. Start (Sample Image) Shut Down menu Click Sleep.
Page 90 Getting Started Turning off the computer Click Change plan settings under the power plan to be customized. The Edit Plan Settings window appears. (Sample Image) Edit Plan Settings screen To change the amount of time after which the computer enters Sleep mode: Under Put the computer to sleep, select the desired amount of time in both the On battery and Plugged in...
Page 91 Click Change advanced power settings. The Advanced settings tab of the Power Options window appears. (Sample Image) Advanced settings tab of Power Options screen Click Power buttons and lid to display the actions that you can configure. Select Sleep for the options you want. NOTE These options can be set separately for how they operate while the computer is running on battery power or while connected to AC...
Page 92: Closing The Display Panel
Getting Started Customizing your computer’s settings Once the computer is configured, you can place it into Sleep mode by either pressing the power button or closing the display panel, depending on the Sleep options set. Starting again from Sleep mode To start up the computer from Sleep mode, press the power button until the ON/OFF light glows white.
Page 93: Moving The Computer
You may want to secure your computer to a heavy object such as your desk. The easiest way to do this is to purchase an optional computer lock cable. For more information on purchasing a cable lock, visit accessories.toshiba.com. (Sample Illustration) Computer lock cable To secure the computer: Wrap the cable through or around some part of a heavy object.
Page 94 Getting Started Caring for your computer Insert the cable’s locking end into the security lock slot on your computer, then engage the locking device. The computer is now securely locked. (Sample Illustration) Attaching security lock cable...
Page 95: Chapter 2: Learning The Basics
Chapter 2 Learning the Basics This chapter gives some computing tips and provides important information about basic features. Computing tips Save your work frequently. Your work stays in the computer’s temporary memory until you save it to the internal storage drive. If the network you are using goes down and you must restart your computer to reconnect, or your battery runs out of charge while you are working, you will lose all work since you last saved.
Page 96 Learning the Basics Computing tips Back up your files to external media on a regular basis. Label the backup copies clearly and store them in a safe place. It is easy to put off backing up because it takes time. However, if your internal storage drive suddenly fails, you will lose all the data on it unless you have a separate backup copy.
Page 97: Using The Keyboard
Using the keyboard Your computer’s keyboard contains character keys, control keys, function keys, and special Windows (Sample Illustration) Keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: The space bar creates a space character instead of just passing over an area of the page.
Page 98: Special Windows ® Keys
Learning the Basics Starting a program key, function keys marked with icons execute specific functions on the computer. For example, more information, see ® Special Windows keys (Sample Illustration) Special Windows Your computer’s keyboard has one key and one button that have special functions in Windows Windows Application key—Has a similar function as the secondary...
Page 99: Starting A Program From The Start Menu
Starting a program from the Start menu When you install a program, the operating system usually puts an icon in the All Programs menu. To start a program that has an icon in the All Programs menu, follow these steps, which use the ®...
Page 100: Starting A Program Using The Start Search Field
Learning the Basics Starting a program In the left part of the window, click the line that ends in “Local Disk (C:).” In the left part of the window, under the Local Disk C: icon, double-click the folder containing the program, in this case Program Files.
Page 101: Saving Your Work
Saving your work Before you turn off the computer using the Shut Down command, save your work on the internal storage drive, diskette, flash media, or optical disc. This is one of the most important rules of computing. When you turn off the computer using the Sleep or Hibernate commands, your work should be there when you resume.
Page 102: Printing Your Work
Learning the Basics Printing your work HINT: To make another copy of the file you are currently working with, click File, and then Save As, and give the new file a different name. File names The Windows contain up to 260 characters and can include spaces. Some applications do not support long file names and require file names limited to no more than eight characters.
Page 103: Backing Up Your Work
In your Windows The program displays a Print dialog box. (Sample Image) Print dialog box Specify the print parameters. For example, the range of pages and number of copies to print. Click Print. Backing up your work Back up all the files you create in case something happens to your computer.
Page 104: Restoring Your Work
Learning the Basics Using the optical drive Restoring your work To restore information from your backup media to your internal storage drive, use the Restore page in the backup program. Look in the online Help or your operating system documentation for information on restoring files.
Page 105: Optical Drive Components
Optical drive components The optical drive is located on the side of the computer. The Media control buttons are located above the keyboard and can be accessed when the display panel is open. Depending on the type of drive on your computer, the procedure to insert and remove optical discs may differ.
Page 106: Media Control Buttons
Learning the Basics Using the optical drive Media control buttons The media control buttons located on the system control panel above the keyboard let you mute the sound and play audio CDs or DVD movies when the computer is on. Previous track button Play/Pause button Media button...
Page 107: Removing A Disc (Slot-Type Drive)
If the disc is dusty, clean it as described in discs” on page With the label facing up, carefully place the disc partially into the slot until the disc stops or the drive starts pulling the disc in. (Sample Illustration) Positioning the disc in the drive Use only standard (12 cm) CD or DVD Discs.
Page 108: Inserting An Optical Disc (Tray-Type Drive)
Learning the Basics Using the optical drive Inserting an optical disc (tray-type drive) (Available on certain models) To insert an optical disc into the drive: Make sure the computer is turned on. The drive will not open if the computer’s power is off. Make sure the drive’s in-use indicator light is off.
Page 109 If you insert the disc incorrectly, it may jam the drive. If this happens, contact Toshiba support for assistance. Push the disc tray in by pressing gently on the center of the tray until it clicks into place.
Page 110: Playing An Audio Cd
Play pre-recorded and recorded optical media. Read/write data and multi-media files to recordable optical media. For more information regarding supported optical media formats please refer to your computer’s detailed specifications at pcsupport.toshiba.com. ® Player and use it to select and...
Page 111: Removing A Disc With The Computer On (Tray-Type Drive)
Due to manufacturing and quality variations in third party optical media (e.g., CD or DVD) or optical media players/recorders, in certain cases, your Toshiba optical drive may not record on certain optical media that bear the applicable logo, or play back optical media recorded by other computers or optical media recorders.
Page 112: Caring For Optical Discs
Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect. These sites provide information about Toshiba products, give help with technical questions and keep you up to date with future upgrades.
Page 113: Chapter 3: Mobile Computing
It has a number of other features that enhance its energy efficiency. Many of these energy-saving features have been preset by Toshiba. We recommend you leave these features active, allowing your computer to operate at its maximum energy efficiency, so that you...
Page 114: Running The Computer On Battery Power
This is normal for all batteries. To purchase a new battery pack, see the accessories information included with your computer or visit the Toshiba Web site at accessories.toshiba.com. Use only batteries designed to work with your Toshiba computer.
Page 115: Power Management
Never leave batteries in the battery charger for more than a week at a time. Doing so may reduce the potential charge of the battery. Always use the battery charger specified by Toshiba. You can order a Toshiba battery charger from Toshiba’s Web site at accessories.toshiba.com.
Page 116: Charging The Main Battery
Mobile Computing Charging batteries Charging the main battery To charge the main battery while it is in your computer, plug the computer into a live electrical outlet. The battery charges whether the computer is on or off. TECHNICAL NOTE: The recharging of the battery cannot occur when your computer is using all of the power provided by the AC adaptor to run applications, features, and devices.
Page 117: Monitoring Main Battery Power
To recharge the RTC battery, plug the computer into a live electrical outlet and leave the computer powered on for 24 hours. NOTE It is seldom necessary to charge the RTC battery because it charges while the computer is on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date or stop working.
Page 118 Mobile Computing Monitoring main battery power HINT: Be careful not to confuse the battery light ( light ( the keyboard). When the ON/OFF light or power button light flashes amber, it indicates that the system is suspended (using the Windows operating system Sleep command).
Page 119: Determining Remaining Battery Power
Determining remaining battery power Wait at least 16 seconds after turning on the computer before trying NOTE to monitor the remaining battery power. The computer needs this time to check the battery’s remaining capacity and perform its calculations. Move the cursor over the power icon in the Notification Area, see “Finding your way around the desktop”...
Page 120: Setting Battery Notifications
Mobile Computing Monitoring main battery power Setting battery notifications You can set two notifications. Each notification can be set to alert you when a specified percentage of remaining battery power has been reached. You can also set the computer to enter Sleep mode or Hibernation mode or to completely power down when the notification goes off.
Page 121: Conserving Battery Power
Conserving battery power How long a fully charged battery pack lasts when you are using the computer depends on a number of factors, such as: How the computer is configured How much you use the internal storage drive, optical drive, diskette drives, or other optional devices Where you are working, since operating time decreases at low temperatures...
Page 122: Power Plans
Mobile Computing Monitoring main battery power Power Plans You can choose a predefined Power Plan or select your own combination of power options. To do this: Click Start, Control Panel, Mobile PC, and then Power Options. The Windows (Sample Image) Windows Select an appropriate plan for your work environment or create your own custom plan.
Page 123: Using A Hot Key To Set The Power Plan
Click Save Changes to save the plan changes you have performed. By default the three power plans Balanced, eco, and High Performance are satisfactory for most people and do not need to be edited. The eco plan is the best used for maximum battery time. The High Performance plan will give you the shortest battery time, but the highest performance from your computer.
Page 124: Using Toshiba Eco Mode
(Sample Illustration) Locating the eco utility button The TOSHIBA eco Utility monitors your power savings from using eco Mode by tracking real-time power consumption and accumulated savings over time. To learn how to access the utility, “TOSHIBA eco Utility”...
Page 125: Changing The Main Battery
Changing the main battery When your main battery has run out of power, you have two options: plug in the AC adaptor or install a charged main battery. Never short circuit the battery pack by either accidentally or intentionally bringing the battery terminals in contact with another conductive object.
Page 126 Mobile Computing Changing the main battery Slide the battery release lock to the unlocked position. (Sample Illustration) Unlocking the battery release lock Slide the battery release latch to release the battery. Pull the discharged battery out of the computer. (Sample Illustration) Removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately.
Page 127: Inserting A Charged Battery
Inserting a charged battery To insert a battery: Wipe the terminals of the charged battery with a clean cloth to ensure a good connection. Insert the charged battery into the slot until the latch clicks. The battery pack has been designed so that you cannot install it with reverse polarity.
Page 128: Taking Care Of Your Battery
If a battery is leaking or damaged, replace it immediately. Use protective gloves when handling a damaged battery. To replace the main battery, use an identical battery that you can purchase through the Toshiba Web site at accessories.toshiba.com. A reverse polarity condition should be avoided with all batteries.
Page 129: Maintaining Your Battery
Maintaining your battery Fully discharging your battery pack will allow better accuracy of the battery meter. To fully discharge your battery pack: Periodically, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges.
Page 130 If you cannot find the information you need elsewhere, call Toshiba at: (800) 457-7777. In addition, Toshiba’s recycling initiatives include recycling programs, events and consumer promotions. For details, visit www.ToshibaDirect.com, select Recycling &...
Page 131: Traveling Tips
Never leave your computer on a sunny ledge or in a place where it could get wet or covered in dust. Always travel with the computer in a carrying case. Toshiba offers a choice of carrying cases for the computer. They all provide plenty of extra space for manuals, power cords, and compact discs.
Page 132: Chapter 4: Exploring Your Computer's Features
Chapter 4 Exploring Your Computer’s Features In this chapter, you will explore some of the special features of your computer. Exploring the desktop The desktop is the launching pad for everything you can do in the ® Windows operating system. You use its features to start programs, find documents, set up system components, and perform most other computing tasks.
Page 133: Finding Your Way Around The Desktop
Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, Taskbar, Notification Area, and background pattern. Icons Start button (Sample Image) Windows Icons An icon represents a folder, file, or program that can be quickly activated by double-clicking the icon.
Page 134 Exploring Your Computer’s Features Exploring the desktop Your desktop may contain other icons depending on your configuration. See Windows information on each icon and how to use it. Start button You use the Start button to: Start programs Open documents Adjust system settings Find files Access Windows...
Page 135: Setting Up For Communications
Setting up for communications To connect to the Internet, use an online service, or communicate across the telephone lines with another computer, you need: A browser or communications program An Internet Service Provider (ISP) or online service if you plan to use the Internet A way to connect to the ISP (for example modem/ ®...
Page 136: Connecting A Modem To A Telephone Line
Exploring Your Computer’s Features Setting up for communications Accessing a network To access a network: At the office, connect an Ethernet cable to the Network port (RJ45) on your computer. For specific information about connecting to the network, consult your network administrator. Many hotels, airports, and offices offer Wi-Fi computer has Wi-Fi their Wi-Fi...
Page 137 Before you can communicate using the modem, you need to connect it to a telephone line. Your computer’s built-in modem port provides an RJ-11 jack, allowing you to connect the modem to a standard voice-grade telephone line. Plug one end of a telephone cable (purchased separately) into the modem port on the side of the computer.
Page 138: An Overview Of Using The Internet
Exploring Your Computer’s Features An overview of using the Internet An overview of using the Internet The following sections give a quick introduction to the Internet and some of its exciting features, under these headings: The Internet The World Wide Web Internet Service Providers Connecting to the Internet Surfing the Internet...
Page 139: Connecting To The Internet
Connecting to the Internet To connect to the Internet, you need: A modem and telephone line, or a LAN connection A Web browser An Internet Service Provider (ISP) account Once you have established an ISP account, you can connect to the Internet.
Page 140: Uploading To, And Downloading Files From, The Internet
Exploring Your Computer’s Features An overview of using the Internet Internet chat rooms A chat room is a Web site that offers a place where people with similar interests and ideas communicate in real-time, one-on- one or in groups, by typing messages which are instantly viewed by others on their computer screens.
Page 141: Exploring Audio Features
Exploring audio features You can use your computer to record sounds using the computer’s internal microphone (available on certain models) or an optional external microphone. You can listen to sound files or audio CDs using the built-in speakers, headphones, or external speakers. Recording sounds You may record sounds using the computer’s internal microphone (available on certain models) or by connecting an optional external...
Page 142: Using The Web Camera
Exploring Your Computer’s Features Using the Web Camera TECHNICAL NOTE: When using amplified speakers, use speakers that require an external power source. Other types of speakers will be inadequate to produce sound from the computer. To play back sound files through external speakers or headphones: Locate the headphone jack on the computer.
Page 143: Using An Expresscard
Using an ExpressCard The ExpressCard slot also supports hot swapping, which allows you to replace one ExpressCard with another while the computer is on. Inserting an ExpressCard Before you insert an ExpressCard comes with the card to see if you need to do anything before you insert it.
Page 144: Using The Bridge Media Adapter Slot
To use a micro or mini SD card, an SD adapter is required. The Bridge Media Adapter slot may also support other types of media. For a complete list of supported media, visit Toshiba’s Web site at accessories.toshiba.com. NOTE Do not use the Copy Disk function for this type of media.
Page 145: Inserting Memory Media
Inserting memory media The following instructions apply to all types of supported media devices. Turn the media so that the contacts (metal areas) are face down. Push the media into the adapter until it locks in place. (Sample Illustration) Inserting memory media When inserting memory media, do not touch the metal contacts.
Page 146: Using The I.link ® Port
Exploring Your Computer’s Features Using the i.LINK Do not remove memory media while data is being written or read. Even when the Windows to the media might still be in progress and your data could be destroyed. Wait for the indicator light to go out. ®...
Page 147: Chapter 5: Utilities
TOSHIBA Assist TOSHIBA Application Installer Supervisor password User password TOSHIBA Face Recognition Utility TOSHIBA PC Diagnostic Tool Utility TOSHIBA HDD Protection Utility TOSHIBA SD™ Memory Card Format Utility Mouse Utility TOSHIBA Hardware Setup...
Page 148: Toshiba Assist
TOSHIBA PC Health Monitor ConfigFree® TOSHIBA Assist The TOSHIBA Assist provides quick access to computer functions and allows you to customize a range of computer settings. To access TOSHIBA Assist, click Start, All Programs, Toshiba, Utilities, and then TOSHIBA Assist.
Page 149: Connect
The TOSHIBA Assist offers four categories of options: Connect Secure Protect & Fix Optimize Connect The features available in this category are: ConfigFree Bluetooth (Sample Image) TOSHIBA Assist window – Connect tab ® Connectivity Doctor ® Settings Utilities TOSHIBA Assist...
Page 150: Secure
Utilities TOSHIBA Assist Secure The features available in this category are: Supervisor password User password (Sample Image) TOSHIBA Assist window – Secure tab...
Page 151: Protect & Fix
Protect & Fix The features available in this category are: TOSHIBA PC Diagnostic Tool Utility TOSHIBA HDD Protection Utility (Sample Image) TOSHIBA Assist window – Protect & Fix tab Utilities TOSHIBA Assist...
Page 152: Optimize
TOSHIBA Assist Optimize The features available in this category are: TOSHIBA SD™ Memory Card Format Utility Mouse Utility TOSHIBA Hardware Setup TOSHIBA Zooming Utility TOSHIBA Button Support TOSHIBA Accessibility TOSHIBA Face Recognition Utility (Sample Image) TOSHIBA Assist window – Optimize tab...
Page 153: Toshiba Application Installer
TOSHIBA Application Installer The TOSHIBA Application Installer allows you to reinstall the drivers and applications that were originally bundled with your computer. To reinstall drivers and applications: Click Start, All Programs, Toshiba, Recovery, and then TOSHIBA Application Installer. Click Next.
Page 154: Setting Passwords
When you set a password, you must enter the password before you can work on your computer again. Toshiba supports several types of passwords on your computer: An instant password—Secures your open programs and files when leaving the computer temporarily.
Page 155: Using A Supervisor Password
Toshiba is not responsible for any losses that may occur to you, your organization or others as a result of the inability to access your computer.
Page 156: Using A User Password
Toshiba is not responsible for any losses that may occur to you, your organization or others as a result of the inability to access your...
Page 157: Deleting A User Password
To register a password for the power-on password functions: Click Start, All Programs, Toshiba, Utilities, and then TOSHIBA Password Utility. The TOSHIBA Password Utility window appears. (Sample Image) TOSHIBA Password Utility window Click Registered. Enter your password, and then enter it again to verify.
Page 158: Toshiba Face Recognition Utility
Toshiba does not guarantee that the face recognition utility will accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of the face recognition software or utility.
Page 159: Toshiba Pc Diagnostic Tool Utility
Refer to the online Help documentation within the application for additional help. NOTE The TOSHIBA PC Diagnostic Tool utility may show tests for features you do not have. This is normal and does not indicate a problem. To use the TOSHIBA PC Diagnostic Tool utility:...
Page 160: Toshiba Hdd Protection Utility
Utilities TOSHIBA HDD Protection Utility TOSHIBA HDD Protection Utility The TOSHIBA HDD Protection Utility controls your computer’s hard disk drive (HDD) protection feature, which parks the HDD whenever motion is detected on the computer. Using this utility, you can enable or disable hard disk drive (HDD) protection, and set the motion detector’s sensitivity level for AC power and battery...
Page 161: Toshiba Sd™ Memory Card Format Utility
This utility is used to format SD Adapter slot. To format an SD memory card using this utility: Click Start, All Programs, Toshiba, Utilities, and then SD Memory Card Format. The TOSHIBA SD Memory Card Format screen appears. (Sample Image) TOSHIBA SD Memory Card Format screen Select the drive corresponding to the SD memory card.
Page 162: Mouse Utility
To access the Mouse utility: Click Start, Control Panel, and then Mouse under Hardware and Sound, or click the Mouse icon in the Optimize tab of TOSHIBA The Mouse Properties screen appears. (Sample Image) Mouse Properties screen The settings you can change are divided into these categories:...
Page 163: Toshiba Hardware Setup
Windows system. To access it: Click Start, All Programs, Toshiba, Utilities, and then HWSetup, or click the TOSHIBA Hardware Setup icon in the Optimize tab of The TOSHIBA Hardware Setup screen appears. (Sample Image) TOSHIBA Hardware Setup screen – General tab...
Page 164 Utilities TOSHIBA Hardware Setup Button Setting—Lets you set the conditions for the power button and/or the other buttons. (Sample Image) TOSHIBA Hardware Setup screen - Button Setting tab options Display—Allows you to change the default settings for the built-in display NOTE When the computer restarts, it remembers the last configuration.
Page 165: Usb Sleep And Charge Utility
“USB Sleep and Charge function.” It also displays the remaining battery capacity. Starting the USB Sleep and Charge Utility To start this utility, click Start, All Programs, Toshiba, Utilities, and then USB Sleep and Charge. USB Sleep and Charge...
Page 166 Utilities USB Sleep and Charge Utility You can use the "USB Sleep and Charge function" to charge certain USB compatible external devices such as mobile phones or portable digital music players. However, the "USB Sleep and Charge function" may not work with certain external devices even if they are compliant with the USB specification.
Page 167: Enabling Usb Sleep And Charge
Metal paper clips or hair pins/clips will generate heat if they come into contact with USB ports. Do not allow USB ports to come into contact with metal products, for example when carrying the computer in your bag. Enabling USB Sleep and Charge This utility can be used to enable or disable the “USB Sleep and Charge function”...
Page 168: Battery Settings
Adobe Acrobat Icons on the desktop To access the TOSHIBA Zooming Utility: Click Start, All Programs, Toshiba, Utilities, and then TOSHIBA Zooming Utility. The TOSHIBA Zooming Utility Properties screen appears. (Sample Image) TOSHIBA Zooming Utility Properties screen Select the desired option(s).
Page 169: Toshiba Button Support
To zoom in, hold down the down the key and press For more information about how to use the TOSHIBA Zooming Utility, right-click the click Help. TOSHIBA Button Support TOSHIBA Button Support allows you to customize the Mute and Media buttons.
Page 170: Toshiba Accessibility
Utilities TOSHIBA Accessibility TOSHIBA Accessibility The TOSHIBA Accessibility utility allows you to use the create a hot key combination with one of the function keys without pressing the two keys simultaneously as is usually required. Using Accessibility lets you make the press it once, release it, and then press a function key to activate the hot key function.
Page 171: Fingerprint Authentication Utility
Toshiba does not guarantee that the fingerprint utility will accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of the fingerprint software or utility.
Page 172: Fingerprint Logon
Utilities Fingerprint Authentication Utility Fingerprint Logon The fingerprint utility enables logon to your computer using fingerprints. During user enrollment, fingerprint samples are saved and associated with the user’s Windows user attempts to log on again, the user’s fingerprint is read and compared with the user’s enrolled fingerprints;...
Page 173: Fingerprint Reader Limitations
Avoid the following finger conditions for enrollment or recognition as they may result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate. Soaked or swollen finger (e.g., after taking bath) Injured finger Wet finger Soiled or oily finger Extremely dry skin condition on finger Observe the following to improve the fingerprint recognition success rate.
Page 174: Toshiba Eco Utility
Toshiba does not guarantee that the fingerprint reader will recognize the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility.
Page 175: Toshiba Service Station
TOSHIBA Service Station The TOSHIBA Service Station helps you keep your new computer running at its best by notifying you when updated software, firmware, documentation or other information is available for your computer. If you have enabled the TOSHIBA Service Station, it will alert you when updates are available, and you can then choose to install the updates if you wish.
Page 176: Toshiba Pc Health Monitor
This information is used to identify and provide a notification of system conditions that may affect the performance of your Toshiba computer. It may also be used to help diagnose problems should the computer require service by Toshiba or Toshiba's authorized service providers.
Page 177: Enabling The Toshiba Pc Health Monitor
Once enabled, you may disable the TOSHIBA PC Health Monitor at any time by uninstalling the software via Add/Remove Programs in the Windows all collected information from the internal storage drive.
Page 178 TOSHIBA PC Health Monitor Click Next to continue. The Windows User Account Control screen displays. Click Continue. The PC Health Monitor and TOSHIBA Service Station software terms of use display. Read the displayed information carefully. Choose one of the following options: Accept both...
Page 179: Configfree
Click Start, All Programs, Toshiba, and then ConfigFree. Double-click the ConfigFree icon Press the TOSHIBA Assist button (if applicable to your system) to open the TOSHIBA Assist, and then click the ConfigFree icon. Click the ConfigFree icon then click the desired utility.
Page 180: Configfree ® Utilities
Utilities ConfigFree® NOTE If your computer is not connected to a network, the ConfigFree icon in the Notification Area is displayed with an “X.” ® ConfigFree Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network connection problems. Using Connectivity Doctor, you can view detailed network information by simply moving the mouse pointer.
Page 181 Profile Settings The Profile Settings utility lets you save network settings in ® “profiles.” ConfigFree network settings and devices. You can switch network settings simply by selecting the profile with the desired settings. If you visit a client company occasionally, for example, you can set up a profile to match that environment and connect to the network.
Page 182 Utilities ConfigFree® Click Open Settings. The ConfigFree Profile Settings window appears. (Sample Image) ConfigFree Profile Settings window Click Add to start the Create Profile Wizard.
Page 183: Chapter 6: If Something Goes Wrong
This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter.
Page 184: Problems When You Turn On The Computer
If Something Goes Wrong Problems when you turn on the computer Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. Select the program you want to close, then click End Task. Closing the failed program should allow you to continue working.
Page 185 Problems when you turn on the computer If you are using an AC adaptor, verify that the computer is receiving power from the external power source by looking at the AC power light. If the indicator is glowing, the computer is connected to a live external power source.
Page 186 Try turning the computer on again. If the computer starts normally, the AC adaptor may be defective and will need to be replaced (see the Toshiba Web site at accessories.toshiba.com). If the AC power light starts flashing, remove the battery, and continue with the steps below.
Page 187: The Windows Operating System Is Not Working
The Windows Verify that the AC adaptor is the correct unit for your computer model. The computer may not be able to start from an AC adaptor that is rated for less current (amperage) than the computer requires, even if the rated voltage is correct, and the plug fits correctly in the DC-IN socket.
Page 188: Internet Problems
If Something Goes Wrong The Windows Safe Mode with Command Prompt Enable Boot Logging Enable low-resolution video (640x480) Last Known Good Configuration (advanced) Directory Services Restore Mode Debugging Mode Disable automatic restart on system failure Disable Driver Signature Enforcement Start Windows When you highlight each option using the arrow keys, Windows displays information about each option at the bottom after Description.
Page 189: The Windows Operating System Can Help You
Click one of the options listed in the window and then follow the on-screen instructions. You can connect to Support Online by clicking Microsoft Customer Support or by going to Toshiba support at pcsupport.toshiba.com. Resolving a hardware conflict If you receive an error message telling you there is a device driver conflict or a general hardware problem, try using Windows and Support to troubleshoot the problem first.
Page 190: Fixing A Problem With Device Manager
If Something Goes Wrong Resolving a hardware conflict The device most recently connected to the system is the one most likely to be causing a conflict. Resolving conflicts There are several things you can do to resolve hardware conflicts: Get the most recent drivers from the manufacturer. Disable the device.
Page 191: Memory Problems
The Resources tab, which lists resources assigned to the monitor, optional external optical drive, optional external diskette drive, and other power-using functions. This tab does not appear if the device is not using resources. The Driver tab, which displays the drivers being used by the device.
Page 192: Power And The Batteries
If Something Goes Wrong Resolving a hardware conflict NOTE For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. Power and the batteries Your computer receives its power through the AC adaptor and power cord/cable or from the system batteries (battery, optional...
Page 193: Keyboard Problems
After a period of time, the battery will lose its ability to perform at maximum capacity and will need to be replaced. This is normal for all batteries. To purchase a new battery pack, see your accessories information included with your computer, or visit the Toshiba Web site at accessories.toshiba.com.
Page 194: Display Problems
If Something Goes Wrong Resolving a hardware conflict Display problems Here are some typical display problems and their solutions: The screen is blank. Display Auto Off may have gone into effect. Press any key to activate the screen. You may have activated the instant password feature by pressing simultaneously.
Page 195 To change the number of colors displayed: Right-click in a blank area of the Windows Click Personalize, and then Display Settings. Change the Colors option and click OK. For more information see Windows A message displays saying that there is a problem with your display settings and that the adapter type is incorrect or the current settings do not work with your hardware.
Page 196: Disk Or Internal Storage Drive Problems
If Something Goes Wrong Resolving a hardware conflict Disk or internal storage drive problems Problems with the internal storage drive or with a diskette drive usually show up as an inability to access the drive or as sector errors. Sometimes a drive problem may cause one or more files to appear to have garbage in them.
Page 197: Optical Drive Problems (Tray-Type Drive Only)
Your data files are damaged or corrupted. Refer to your software documentation for file recovery procedures. Many software packages automatically create backup files. You may also be able to recover lost data using utility software. Consult your network administrator. Some programs run correctly but others do not. This is probably a configuration problem.
Page 198: Sound System Problems
For more information regarding supported optical media formats, refer to the complete detail specifications for your computer at pcsupport.toshiba.com. If the problem is with an optical data disc, refer to the software’s documentation and check that the hardware configuration meets the program’s needs.
Page 199 the ExpressCard for information about using the card under the operating system. ® ExpressCard checklist Make sure the card is inserted properly into the slot. Make sure all cables are securely connected. Occasionally a defective ExpressCard control. If another computer with a ExpressCard slot is available, try the card in that machine.
Page 200: Printer Problems
If Something Goes Wrong Resolving a hardware conflict Hot swapping (removing one ExpressCard another without turning the computer off) fails. Follow this procedure before you remove an ExpressCard Click the Safely Remove Hardware icon in the Notification Area. The Safely Remove Hardware screen appears. Click Safely remove for the device you want to swap.
Page 201: Modem Problems
Run the printer’s self-test to check for any problem with the printer itself. Make sure you installed the proper printer drivers as shown in “Setting up a printer” on page 81 with the printer. You may have connected the printer while the computer is on. Disable Sleep mode, turn off the computer, and turn off the printer.
Page 202: Wireless Networking Problems
To determine if your computer has an internal Wi-Fi the device list in Device Manager (part of the Windows Panel, Hardware and Sound). Some Toshiba models may have a Wireless antenna ON/OFF switch even though they do not have an...
Page 203 Resolving a hardware conflict Verify that the network connection is configured to obtain its Internet Protocol (IP) address dynamically: Click Start, and then Network. Click View Status. Click Details. Verify that the DHCP Enabled setting is set to Yes. Click Close. Use IPCONFIG to verify that the computer has a useful IP address—one other than the private address of 169.254.xxx.xxx assigned by Windows...
Page 204: Dvd Operating Problems
“Checking device properties” on page 190 on using Device Manager to view the optical drive properties. Check the Toshiba Web site for new information on optical drives and their operation. A blank screen appears while watching a DVD-ROM movie or title.
Page 205: Develop Good Computing Habits
Click Save changes. The screen saver runs while you are watching a movie or title. If the screen saver is enabled, it runs on top of any movie or title you are watching. To disable the screen saver: Right-click on the desktop and click Personalize in the menu. Select None for the screen saver.
Page 206: Data And System Configuration Backup In The Windows
If Something Goes Wrong Develop good computing habits Get familiar with all the user’s guides provided with your computer, as well as the manuals that come with the programs and devices you purchase. Your local computer store or book store sells a variety of self-help books you can use to supplement the information in the manuals.
Page 207 An external hard drive is recommended in case the internal storage drive fails. No additional software is required. Most of the optical drives built into recent Toshiba If Something Goes Wrong Develop good computing habits operating system.
Page 208 If Something Goes Wrong Develop good computing habits portable computer models can write to (or ‘burn’) as well as read from optical discs. External optical disc writers are also widely available. Follow these steps to back up your computer or files to optical discs, or a storage drive: NOTE You cannot back up the computer while running on battery power.
Page 209 Develop good computing habits Back up your critical data (see entire computer with the Windows page 207). Have your factory Restore/Reconfiguration CD(s) on hand in case you need any files from them (available on certain models). Do not guess—follow directions carefully! It is often necessary to run an installation utility first—before connecting a new hardware item to the computer.
Page 210: Hibernation Mode
If Something Goes Wrong Develop good computing habits Cannot use the “USB Sleep and Charge function.” The setting of “USB Sleep and Charge function” may be Disabled. Change the setting to Enabled. Some external devices may not be able to use the “USB Sleep and Charge function”.
Page 211: If You Need Further Assistance
Go to the Tech Support Center, select your particular model from the list and go to the Detailed Specifications for that model. For the number of a Toshiba dealer near you in the United States, call: (800) 457-7777. Contacting Toshiba If you still need help and suspect that the problem is hardware- related, Toshiba offers a variety of resources to help you.
Page 212: Other Toshiba Internet Web Sites
Information about what you were doing when the problem occurred Exact error messages and when they occurred For technical support, call the Toshiba Customer Support Center: Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273 Other Toshiba Internet Web sites toshiba.com...
Page 213 Spain United States Toshiba America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 United States For more information on additional Toshiba worldwide locations, please visit: www.toshiba.co.jp/index.htm. If Something Goes Wrong Toshiba’s worldwide offices Germany Toshiba Europe GmbH Leibnizstraße 2...
Page 214: Appendix A: Hot Keys/Toshiba Cards
Appendix A Hot Keys/TOSHIBA Cards Hot keys and TOSHIBA Cards provide a quick way to modify selected system functions and to launch applications. There are two types of TOSHIBA Cards: Hot Key Cards and Application Cards. Hot Key Cards The Hot Key Cards are used to set or modify the following system...
Page 215: Using The Hot Key Cards
To use the Hot Key Cards: Press and hold the The TOSHIBA Cards appear along the top of the screen. (Sample Image) Hot Key Card display Double-click the Card for the system function to be modified.
Page 216: Application Cards
TOSHIBA Zooming utility For more information, refer to Zooming Utility” on page Disc Creator utility This Application Card launches the TOSHIBA Disc Creator utility. TOSHIBA Hardware Setup utility For more information, refer to Hardware Setup” on page TOSHIBA Button Support utility For more information, refer to Support”...
Page 217: Using The Application Cards
Using the Application Cards To launch an application using the Application Cards: Press and hold the The TOSHIBA Cards display at the top of the screen. (Sample Image) TOSHIBA Card display Click the “stacked” card on the far right of the display. The Application Cards are hidden under this card.
Page 218: Card Case
The Card Case feature allows you to choose which cards appear in the Application Card display (see page 217). To use the Card Case: Click Start, All Programs, Toshiba, Utilities, and then Settings for Flash Cards. (Sample Image) Enabling and Disabling Application Cards Click the Open cards case button.
Page 219: Volume Mute
Volume Mute This TOSHIBA Card or hot key enables/disables volume mute on your computer. When volume mute is enabled, no sound will come from the speakers or headphones. Selecting this Card or pressing the hot key displays the following options:...
Page 220: Lock (Instant Security)
Hot Keys/TOSHIBA Cards Hot key functions Lock (Instant security) This TOSHIBA Card or hot key blanks the display. Selecting this Card or pressing the hot key displays the following options: (Sample Image) Security options hot key function activates instant security. The user...
Page 221: Power Plan
Hot Keys/TOSHIBA Cards Hot key functions Power plan This TOSHIBA Card or hot key displays the power plans and cycles through the power plans. The properties of each power plan, and the power plans that are displayed by this function, are set in the Power Options window.
Page 222: Sleep Mode
Hot Keys/TOSHIBA Cards Hot key functions Sleep mode This TOSHIBA Card or hot key places the computer into Sleep mode. For more information about Sleep mode, please see and configuring Sleep mode” on page Selecting this Card or pressing the hot key displays the...
Page 223: Hibernation Mode
Hibernation mode This TOSHIBA Card or hot key places the computer into Hibernation mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page Selecting this Card or pressing the hot key displays the...
Page 224: Output (Display Switch)
Hot Keys/TOSHIBA Cards Hot key functions Output (Display switch) This TOSHIBA Card or hot key cycles through the power- on display options (only the first option is available when you do not have an external monitor attached) (the last option is available only if you are in Extended Display Mode).
Page 225: Display Brightness
To swap sides, select Swap Image Display. Display brightness This TOSHIBA Card decreases or increases the screen brightness. This hot key decreases the screen brightness. This hot key increases the screen brightness.
Page 226: Disabling Or Enabling Wireless Devices
Hot Keys/TOSHIBA Cards Hot key functions Disabling or enabling wireless devices This TOSHIBA Card or hot key enables/disables the optional wireless devices installed in your computer. The wireless modes are: Selecting this Card or pressing the hot key displays the...
Page 227: Disabling Or Enabling The Touchpad
Disabling or enabling the TouchPad™ This TOSHIBA Card or hot key enables/disables the TouchPad. For more information on using the TouchPad, see the TouchPad™” on page Selecting this Card or pressing the hot key displays the following options: (Sample Image) Disable or Enable TouchPad options...
Page 228: Zoom (Display Resolution)
Hot Keys/TOSHIBA Cards Hot key functions Zoom (Display resolution) This TOSHIBA Card or hot key switches screen resolution. Selecting this Card or pressing the hot key displays the following options: [Space bar] (Sample Image) Screen resolution options Cycle through the screen resolutions, then select the desired...
Page 229: Keyboard Hot Key Functions
Keyboard hot key functions This hot key turns the TOSHIBA Zooming Utility to zoom-out. This hot key turns the TOSHIBA Zooming Utility to zoom-in. This hot key turns the backlit keyboard off and on. (Available on certain models) Hot Keys/TOSHIBA Cards...
Page 230: Appendix B: Power Cord/Cable Connectors
Appendix B Power Cord/Cable Connectors Your computer ships with the correct power supply for the country of purchase. This appendix shows the shapes of the typical AC power cord/cable connectors for various parts of the world. UL approved United Kingdom BS approved Australia AS approved...
Page 231: Glossary
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide. BIOS CD-ROM CD-RW CMOS COM1 COM2 DIMM alternating current basic input/output system bits per second compact disc compact disc read-only memory compact disc rewrite memory...
Page 232 Glossary DSTN DVD-ROM digital versatile (or video) disc read-only memory EPROM HTML IEEE LPT1 MIDI PCMCIA SCSI disk operating system dots per inch dual supertwist nematic digital versatile (or video) disc enhanced capabilities port erasable programmable read-only memory file allocation table Federal Communications Commission gigabyte hard disk drive...
Page 233 SDRAM SRAM SVGA Terms The following terms may appear in this user’s guide. active-matrix display — A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology. Also known as a “TFT display,” in its simplest form there is one thin film transistor (TFT) for each cell.
Page 234 Glossary baud rate — The speed at which a communication device, such as a printer or modem, transmits information. Baud rate is the number of signal changes per second (not necessarily the same as bits per second). See also bits per second. BIOS (basic input/output system) —...
Page 235 central processing unit (CPU) — The chip that functions as the “brain” of the computer. It takes information from outside sources, such as memory or keyboard input, processes the information, and sends the results to another device that uses the information. character —...
Page 236 Glossary default — The setting selected by a program when the user does not specify an alternative setting. device — A component attached to the computer. Devices may be external (outside the computer’s case) or internal (inside the computer’s case). Printers, disk drives, and modems are examples of devices.
Page 237 double-click — To press and release the pointing device’s primary button rapidly twice without moving the pointing device. In the Windows button, unless otherwise stated. double-density diskette — A 3.5-inch diskette that can hold up to 720 KB of information (half the capacity of a high-density diskette). See also diskette, high-density diskette.
Page 238 Glossary file — A collection of related information, saved on disk with a unique name. A file may be a program, information used by a program, or a document. See also document. file allocation table (FAT) — The section of a storage drive that keeps track of the location of stored files.
Page 239 Hibernation — A feature of many Toshiba computers that saves to the internal storage drive the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned off.
Page 240 Glossary liquid crystal display (LCD) — A type of display that uses a liquid substance between two transparent electrode panels. When an electric current passes through the electrodes, the molecules in the liquid form a crystalline pattern that polarizes the light passing through it.
Page 241 network — A collection of computers and associated devices that are connected by communications facilities. A network allows you to share data and peripheral devices, such as printers, with other users and to exchange electronic mail. non-interlaced — A method of refreshing a computer screen, in which each pixel of every line is refreshed as the electron beam scans across and down the screen.
Page 242 Glossary Plug and Play — Generally, refers to the computer’s ability to automatically configure itself to work with peripheral devices. When capitalized, refers to a standard that, when followed by a device manufacturer, allows a computer to configure itself automatically to work with the device. pointing device —...
Page 243 RJ11 — A modular connector used on most U.S. telephone systems and direct-connect modems. The RJ11 connector is a 6-wire connector. ROM (read-only memory) — Non-volatile memory that can be read but not written to. Non-volatile here means that information in ROM remains whether or not the computer is receiving power.
Page 244 Glossary TFT display — See active-matrix display. universal serial bus (USB) — USB is a serial bus that supports a data transfer rate of up to 480 Mbps (480 million bits per second). USB can connect up to 127 peripheral devices through a single all- purpose USB port.
Page 245: Index
221 power plan hot key 123 real-time clock (RTC) 114 remaining power 119 removing 125 safety precautions 128 BIOS Setup see TOSHIBA Hardware Setup Bridge Media Adapter inserting memory media 145 removing memory media 145 button power 51 start 134...
Page 246 Index changing main battery 125 character keys 97 charging the battery 49 checking device properties 190 click 76 communications network connection 136 set up 135 compact discs handling 106 inserting 107 removing 107 computer caring for 92 cleaning 92 moving 93 non-system disk or disk error message 186 not accessing disk drives 185...
Page 247 eject button optical drive 105 eject, optical drive 105 ENERGY STAR® 38 error messages device driver conflict 189 general hardware problem 189 non-system disk or disk error 186 problem with display settings/ current settings not working with hardware 195 warning resume failure 185 Error-checking 196 eSATA connecting to the eSATA/USB...
Page 248 Index Hot key functions 218 hot key power plan 123 http 138 i.LINK port fast data transfer 146 icon 133 desktop 133 moving to desktop 133 recycle bin 133 safety 41 inserting CDs and DVDs 107 ExpressCards® 143 installation memory module 54 installing main battery 125 memory modules 53...
Page 249 195 checking device properties 190 computer hangs when ExpressCard® inserted 199 computer will not power up 184 contacting Toshiba 211 corrupted/damaged data files 197 Device Manager 190 disk drive is slow 196 display is blank 194 ExpressCard®...
Page 250 Index hot swapping fails 200 not recognized 200 ExpressCard® checklist 198 ExpressCard® slot appears dead external display not working 195 external monitor 194 faulty memory 191 hardware conflict 189 high-pitched noise 198 Internet bookmarked site not found 188 Internet connection is slow 188 keyboard not responding 185 missing files/trouble accessing a...
Page 251 Index TOSHIBA Face Recognition Utility TOSHIBA Hardware Setup 163 TOSHIBA HDD Protection Utility Toshiba online resources 112 TOSHIBA PC Diagnostic Tool Utility TOSHIBA PC Health Monitor 176 TOSHIBA SD™ Memory Card Format Utility 161 TOSHIBA Service Station 175 TOSHIBA Zooming Utility 168 TouchPad™...
Page 252 Index video cables 77 video display device connecting 77 video projector adjusting display 80 warranty standard limited warranty 42 Web 138 Web Camera using 142 Web sites 211 Wi-Fi® wireless networking 135 Windows® Explorer 99 Windows® operating system Help and Support 189 problem solving 187 Windows®...

Toshiba A500-ST5602 User Manual

Chapter 1: Getting Started

Chapter 2: Learning the Basics

Chapter 3: Mobile Computing

Chapter 4: Exploring Your Computer's Features

Chapter 5: Utilities

Chapter 6: If Something Goes Wrong

Appendix A: Hot Keys/Toshiba Cards

Appendix B: Power Cord/Cable Connectors

Quick Links

Related Manuals for Toshiba A500-ST5602

Summary of Contents for Toshiba A500-ST5602