Advertisement
RP5-GM4101 Illustration / Schematic
Vehicle
Connections
RP5-GM4101 Installation Steps
SET RADIO SELECT SWITCH
Alpine
1
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting
before plugging the interface into the vehicle.
2. Make all connections as described in the chart on page 1.
3.
Plug the CMX chime module in if necessary (If the vehicle chimes when the radio is removed the CMX is not necessary). PLEASE NOTE:
In order to get the best possible sound out of the CMX please mount it in a place free and clear of any obstructions, preferably as close as
possible to the bottom of the dash pointing down toward the floor of the vehicle.
4.
The Mute loop (if not cut) will turn the accessory output off when an OnStar or Bluetooth call is made or received. If the aftermarket radio
has a mute input cut this loop and connect the outer brown wire to the mute input.
5.
Connect the SWC wire according to the chart on page 5 (aftermarket radio MUST support a wired remote input).
6.
If you wish to reassign functions to the SWC follow the programming instructions in the next section.
7.
Connect the proper AUX cables depending if your vehicle has the MyLink or standard non-touchscreen radios equipped with a USB port.
8.
Connect the supplied USB retention cable. MyLink radios will have a mini USB cable behind the radio. In this case the USB-GM1 cable (sold
separately) can be used. The supplied cable will need to be ran to the back of the factory USB port located at the rear of the center console.
RP5-GM4101 Default Steering Wheel Control Programming
IMPORTANT!
The interface comes pre-programmed for the functions listed in the chart below and does not require programming unless you
wish to re-assign the SWC functions or utilize short press long press dual command functionality. The SWC can always be restored to default
settings by pressing the program button on the side of the interface once and waiting for the timeout.
The Mute/End button has two functions. Pressing this button for less than 1.5 seconds will initiate the mute command. Pressing this button for
more than 1.5 seconds will initiate the end command. This dual function button can also be reprogrammed to whatever features the customer
chooses.
Default SWC Button Assignments
Volume +
Volume -
Source
Track +
Track -
Answer/Voice
Mute/End
Pacific Accessory Corporation
Wiring
JVC
Kenwood
2
3
Other =
Advent, BOYO, Dual, Jensen, Lightning Audio, Rockford Fosgate & Visteon
Alpine
JVC
Volume +
Volume +
Volume -
Volume -
Source
Source
Track +
Track +
Track -
Track -
Answer/OnStar
Answer/OnStar
Activation
Activation
Mute/Factory
Mute/Factory
Bluetooth End
Bluetooth End
PAC
| 866-931-8021 | support@pac-audio.com
®
©2016 Pacific Accessory Corporation
Aftermarket
Radio
Connections
Clarion /
Pioneer/Other
Nakamichi
4
Clarion/
Kenwood
Pioneer
Nakamichi
Volume +
Volume +
Volume +
Volume -
Volume -
Volume -
Source
Source
Source
Track +
Search +
Track +
Track -
Search -
Track -
Answer/OnStar
Answer/OnStar
Answer/OnStar
Activation
Activation
Activation
Mute/Factory
Mute/Factory
Mute/Factory
Bluetooth End
Bluetooth End
Bluetooth End
www.pac-audio.com
RPK5-GM4101
x3
Complete Radio Replacement Kit with
Integrated Climate Control Retention for
2010-2015 Chevrolet Camaro
SWC Connection
SWC Connection
Sony
7
8
Sony
Fusion
Volume +
Volume +
Volume -
Volume -
Source
Source
Track +
Track +
Track -
Track -
Answer/OnStar
Answer/OnStar
Activation
Activation
Mute/Factory
Mute/Factory
Bluetooth End
Bluetooth End
See above chart for
different radio type
connections
Fusion
9
PAC is an AAMP power brand
Rev. 113016
Page 5
Advertisement
