Advertisement
Assembly of the PAC HVAC control assembly (cont.)
3.4 - Secure the knobs to the circuit
board using the same screws shown in
disassembly step # 7. The screws will pass
through the circuit board and thread into the
knobs via the holes defined below.
RP5-GM4101 Introduction & Features
The RP5-GM4101 interface allows the replacement of a factory radio in the 2010-2015 Chevrolet Camaro. Using this
interface will retain factory features such as OnStar, Bluetooth, steering wheel controls (SWC), AUX Audio, USB and
warning chimes when the original radio is removed. Use of this interface also allows you to program two radio functions
to each SWC button by using short press long press dual command functionality. The RP5-GM4101 also provides data
bus driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS), illumination, reverse trigger
and parking brake.
RP5-GM4101 Important Notes
1. Once the radio has been removed, the vehicle settings which are normally selected through the factory radio can be accessed using the
PAC Interface Updating Device (PAC-UP) along with downloading and installing the PAC Vehicle Settings program (for windows PC) from:
http://www.pac-audio.com/firmware/RP/index.html.
2. As in most radio replacements where the car has a separate Bluetooth module it is recommended that the phone(s) be "Unpaired" with the
factory Bluetooth. This way the phone will always pair to the new radio.
3. The Answer/Voice & End/Mute buttons can be set to do the factory OnStar functions or given the ability to control the aftermarket radio. This
option can be found in the PAC Vehicle Settings program mentioned above in note one. The default setting for these buttons is to control the
factory OnStar. If these buttons are set to control the aftermarket radio, OnStar can still be accessed by using the mirror controls.
4. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the interface into the
vehicle (see below for setting chart).
5. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless you wish to
re-assign the SWC functions or utilize the short press long press dual command functionality. The SWC can always be restored to default
settings by pressing and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to flash 4 times.
6. The LED will flash whenever a SWC button is pressed.
RP5-GM4101 Wiring Connection Chart
Aftermarket Radio Connections
Yellow
Battery +12v
Black
Red
Accessory Output
White
Front Left + input
White / Black
Front Left - input
Grey
Front Right + input
Grey / Black
Front Right - input
Green
Rear Left + input
Green / Black
Rear Left - input
Purple
Rear Right + input
Purple / Black
Rear Right - input
Blue
Blue / White
Amplifier Remote Turn
Pacific Accessory Corporation
Light Green
Pink
Ground
Orange / White
Purple / White
Brown Loop
SWC Connector
Blue / Yellow
3.5mm Jack
Not Used
On
PAC
| 866-931-8021 | support@pac-audio.com
®
©2016 Pacific Accessory Corporation
3.5 - Slide the white fasteners onto the two
black posts at the top of the PAC HVAC
Parking Brake Output (-)
Vehicle Speed Output
Illumination Output (+)
Reverse Output (+)
Mute Loop -
See Note
Installation Step 4 on Page 6
Kenwood, or Newer JVC
Alpine, JVC, Clarion,
Pioneer, Sony, Boyo,
Dual, Lightning Audio,
Visteon, Jensen or Advent
www.pac-audio.com
RPK5-GM4101
Complete Radio Replacement Kit with
Integrated Climate Control Retention for
2010-2015 Chevrolet Camaro
control assembly.
Antenna Adapter
Blue
Power Antenna output from
aftermarket radio
RCA Connectors
Red
AUX Audio Retention Right
White
AUX Audio Retention Left
RCA Connector
(Grey connector)
Yellow
Reverse Camera
3.5
Connector
mm
3.5mm Jack
AUX retention for 2010-
2012 vehicles equipped
with a factory USB port.
(Main Connector)
(Black connector)
PAC is an AAMP power brand
Rev. 113016
Page 4
Advertisement
